Standard Svensk standard · SS-ISO/IEC 7811-7:2021

Transaktionskort - Teknik för dataregistrering - Del 7: Magnetremsa med hög koercivitet och hög densitet (ISO/IEC 7811-7:2018,IDT)

Status: Gällande

Köp denna standard

Standard Svensk standard · SS-ISO/IEC 7811-7:2021

Transaktionskort - Teknik för dataregistrering - Del 7: Magnetremsa med hög koercivitet och hög densitet (ISO/IEC 7811-7:2018,IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 919 SEK
standard ikon pdf

PDF

Pris: 919 SEK
standard ikon

Papper

Pris: 1 470,40 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ
Omfattning
This document is one of a series of standards describing the characteristics for identification cards as
defined in the definitions clause and the use of such cards for international interchange.
This document specifies requirements for a high coercivity magnetic stripe (including any protective
overlay) on an identification card and encoding technique. It takes into consideration both human and
machine aspects and states minimum requirements.
Coercivity influences many of the quantities specified in this document but is not itself specified. The
main characteristic of the high coercivity magnetic stripe is its improved resistance to erasure. This is
achieved with minimal probability of damage to other magnetic stripes by contact while retaining read
compatibility with magnetic stripes as defined in ISO/IEC 7811-2.
This document provides for a card capacity of approximately 10 times that of a card conforming to
ISO/IEC 7811-6. The number of tracks has been increased to 6, each track being approximately half
the width of tracks conforming to ISO/IEC 7811-6, located so that readers designed to read these
high density tracks will also be able to read cards conforming to ISO/IEC 7811-2 and ISO/IEC 7811-6.
Data is encoded in 8 bit bytes using the MFM encoding technique. Data framing is used to limit error
propagation and error correction techniques further improve reliability of reading.
It is the purpose of the ISO/IEC 7811 series of standards to provide criteria to which cards shall perform.
No consideration is given within these standards to the amount of use, if any, experienced by the card
prior to test. Failure to conform to specified criteria is negotiated between the involved parties.
ISO/IEC 10373-2 specifies the test procedures used to check cards against the parameters specified in
this document.
NOTE Numeric values in the SI and/or Imperial measurement system in this document may have been
rounded off and are consistent with, but not exactly equal to each other. Using either system is correct but
intermixing or reconverting values can result in errors. The original design was made using the Imperial
measurement system.

Ämnesområden

Identifieringskort och tillhörande läsarenheter (35.240.15)


Köp denna standard

Standard Svensk standard · SS-ISO/IEC 7811-7:2021

Transaktionskort - Teknik för dataregistrering - Del 7: Magnetremsa med hög koercivitet och hög densitet (ISO/IEC 7811-7:2018,IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 919 SEK
standard ikon pdf

PDF

Pris: 919 SEK
standard ikon

Papper

Pris: 1 470,40 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ

Produktinformation

Språk: Engelska

Framtagen av: Personlig identifiering, SIS/TK 448

Internationell titel: Identification cards - Recording technique - Part 7: High coercivity, high density magnetic stripe (ISO/IEC 7811-7:2018,IDT)

Artikelnummer: STD-80027908

Utgåva: 1

Fastställd: 2021-02-26

Antal sidor: 32