Standard Svensk standard · SS-ISO/ASTM 51631:2020

Praxis för användning av kalorimetriska dosimetrisystem för mätning av stråldoser och för kalibrering av dosimetrar vid elektronstrålar (ISO/ASTM 51631:2020, IDT)

Status: Gällande

Köp denna standard

Standard Svensk standard · SS-ISO/ASTM 51631:2020

Praxis för användning av kalorimetriska dosimetrisystem för mätning av stråldoser och för kalibrering av dosimetrar vid elektronstrålar (ISO/ASTM 51631:2020, IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 635 SEK
standard ikon pdf

PDF

Pris: 635 SEK
standard ikon

Papper

Pris: 1 016 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ
Omfattning
This practice covers the preparation and use of semiadiabatic calorimetric dosimetry systems for measurement of absorbed dose and for calibration of routine dosimetry systems when irradiated with electrons for radiation processing applications. The calorimeters are either transported by a conveyor
past a scanned electron beam or are stationary in a broadened beam.
This document is one of a set of standards that provides recommendations for properly implementing dosimetry in radiation processing, and describes a means of achieving compliance with the requirements of ISO/ASTM Practice
52628 for a calorimetric dosimetry system. It is intended to be read in conjunction with ISO/ASTM Practice 52628.
The calorimeters described in this practice are classified as Type II dosimeters on the basis of the complex effect of influence quantities. See ISO/ASTM Practice 52628.
This practice applies to electron beams in the energy range from 1.5 to 12 MeV.
The absorbed dose range depends on the calorimetric absorbing material and the irradiation and measurement conditions. Minimum dose is approximately 100 Gy and maximum dose is approximately 50 kGy.
The average absorbed-dose rate range shall generally be greater than 10 Gy·s-1.
The temperature range for use of these calorimetric dosimetry systems depends on the thermal resistance of the calorimetric materials, on the calibration range of the temperature sensor, and on the sensitivity of the measurement device.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine
the applicability of regulatory limitations prior to use.
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations
issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Ämnesområden

Strålningsmätning (17.240)


Köp denna standard

Standard Svensk standard · SS-ISO/ASTM 51631:2020

Praxis för användning av kalorimetriska dosimetrisystem för mätning av stråldoser och för kalibrering av dosimetrar vid elektronstrålar (ISO/ASTM 51631:2020, IDT)
Prenumerera på standarden - Läs mer Dölj
Pris: 635 SEK
standard ikon pdf

PDF

Pris: 635 SEK
standard ikon

Papper

Pris: 1 016 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ

Produktinformation

Språk: Engelska

Framtagen av: Kärnenergi, SIS/TK 405

Internationell titel: Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimeter calibrations (ISO/ASTM 51631:2020, IDT)

Artikelnummer: STD-80020614

Utgåva: 1

Fastställd: 2020-03-13

Antal sidor: 16