Standard Svensk standard · SS-EN 14758-1:2012

Plaströrsystem - Självfallsledningar för avloppssystem i mark - PP-MD - Del 1: Specifikationer för rör, rördelar och systemet

Status: Gällande

Köp denna standard

Standard Svensk standard · SS-EN 14758-1:2012

Plaströrsystem - Självfallsledningar för avloppssystem i mark - PP-MD - Del 1: Specifikationer för rör, rördelar och systemet
Prenumerera på standarden - Läs mer Dölj
Pris: 1 045 SEK
standard ikon pdf

PDF

Pris: 1 045 SEK
standard ikon

Papper

Pris: 1 672 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ
Omfattning
This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non- pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also specifies the test parameters for the test methods referred to in this European Standard.
This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours.
NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This European Standard is applicable to PP-MD pipes with or without an integral socket.
NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13.
NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.

Ämnesområden

Rör Allmänt (23.040.01) Utvändiga avloppssystem (93.030)


Köp denna standard

Standard Svensk standard · SS-EN 14758-1:2012

Plaströrsystem - Självfallsledningar för avloppssystem i mark - PP-MD - Del 1: Specifikationer för rör, rördelar och systemet
Prenumerera på standarden - Läs mer Dölj
Pris: 1 045 SEK
standard ikon pdf

PDF

Pris: 1 045 SEK
standard ikon

Papper

Pris: 1 672 SEK
standard ikon pdf + standard ikon

PDF + papper

Fler alternativ Färre alternativ

Produktinformation

Språk: Engelska

Framtagen av: Plaströrssystem, SIS/TK 156/AG 02

Internationell titel: Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system

Artikelnummer: STD-85770

Utgåva: 2

Fastställd: 2012-03-09

Antal sidor: 44

Ersätter: SS-EN 14758-1:2005+A1:2009