Includes Amendment No. 1 (1988).
1993-08-30
2004-06-08
Describes recognized thermal classes for the insulation of electrotechnical products. Considers the thermal evaluation of insulation materials and systems, their interrelationship and the influence...
1984-01-01
2004-06-07
Gives methods of test for the materials defined in IEC 60893-1.
1992-05-31
2003-06-24
Describes two test methods, A and B, for assessing the electric strength of insulating liquids in a divergent field when subjected to standard lightning impulses. Method A is based on a step proced...
1987-03-30
Gives test procedures and calculations for the determination of volume and surface resistivity. Establishes recommendations for: values of voltage and time of application; nature and geometry of el...
1980-01-01
Applies to all types of insulating liquids used in medium and high voltage equipment. Not necessarily adapted to liquids with values of PDIV greater than 70 kV. This publication has the status of a...
1993-10-08
Describes the equipment, arrangement and procedures for measurement of electrostatic charge caused by contact and relative motion between materials and presents examples of model experiment to simu...
2000-07-31
Covers the protection from electrostatic discharge (ESD) damage of all electronic devices (components, assemblies and sub-assemblies) with voltage sensitivity of not lower than 100 V throughout the...
1999-02-26
Provides methods for measuring magnetically hard materials, at elevated temperatures. Magnetically hard materials (permanent magnet materials) are classified in IEC 60404-1 and their properties are...
1999-10-20
Contains the definitions and designations related to, and the general requirements to be fulfilled by, industrial, rigid, moulded, laminated tubes of rectangular cross-section and rods of rectangul...
2002-05-23
Gives the requirements for heat-shrinkable (low and high shrink ratio) polytetrafluorethylene (PTFE) sleeving. It is normally available in expanded internal diameter sizes up to 12 mm in three wall...
2002-06-12
Gives the requirements for glass textile fibre sleeving, uncoated, constructed from a braid of E-type yarn. The sleeving is annealed by heat treatment to assist in maintaining a circular cross-sect...
Gives the requirements for sleeving constructed from polyethylene terephthalate yarn, lightly impregnated with resin to provide mechanical stability. This sleeving has been found suitable for use a...
Gives the requirements for sleeving having the property of expanding its internal diameter when compressed longitudinally and thereafter returning to its initial diameter after release of the compr...
Gives the requirements for three types of E-type glass sleeving using either braided or knitted construction, with a continuous silicone elastomer coating and differentiated by their breakdown volt...
Describes test methods for measuring the rate of dissipation of static charge of insulating and static dissipative materials and products. It includes a generic description of test methods and deta...
2002-06-14
Contains the requirements for polypropylene film tapes with a pressure-sensitive adhesive. Materials which conform to this specification meet established levels of performance. However, the selecti...
2003-05-19
Contains the requirements for pressure-sensitive adhesive tapes made with various backing materials with both sides covered with a pressure-sensitive adhesive. Materials which conform to this spec...
This standard gives the requirements for four types of heat-shrinkable polyolefin sleevings suitable for use at temperatures up to 135 C. Type A Flame retarded, shrink ratio 2:1, Type B Not flame ...
2006-01-12
This standard gives the requirements for two types of heat-shrinkable, not flame retarded, polyolefin sleeving with a nominal shrink ratio of 3:1 and with thick and medium wall. This sleeving has b...
This standard is applicable to heat shrinkable moulded shapes in a range of configurations and materials suitable for insulation, environmental sealing, mechanical protection and strain relief for ...
Covers the determination of the coefficient of starting and sliding friction of plastic film and sheeting when sliding over itself or other substances. The slip properties which are related to the ...
1979-01-01
Describes test procedures for evaluation of the thermal endurance of electrical insulating materials, based on the combined use of sensitive analytical methods for the determination of test acceler...
1991-06-28
Describes the voltage endurance graph, lists test methods illustrating their limitations, and gives guidance for evaluating the a.c. voltage endurance of insulating materials from the results of th...
1993-09-30
2007-08-15
Describes an empirical test procedure intended to indicate the presence of contaminants such as water and solid suspended matter, and the advisability of carrying out drying and filtration treatmen...
1995-08-08
Includes a list of existing published procedures which is not exhaustive.
1990-06-15
2005-08-01
Gives precise instructions, as well as numerical examples. Supersedes the second edition of IEC 60216-3 (1980) and the second edition of IEC 60216-4 (1980).
1990-08-15
2002-02-21