1.1 This test method describes a laboratory procedure for the determination of rheological (flow) properties of single- and multicomponent chemically curing sealants for use in building constructio...
2007-09-05
1.1 This practice covers a calibration technique based on the preparation of standards of known water content. This technique is applicable to the production of standards between 20 and 2000 cm3/m...
2005-11-01
1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The p...
2011-05-20
1.1 This practice covers the procedure for the separation of the vehicle from the pigment in solvent-reducible paint. 1.2 In the development of the practice the following materials were tested: w...
2010-06-01
1.1 These test methods cover the determination of the relationship between the water content and the density of soil-cement mixtures when compacted before cement hydration as prescribed. 1.2 A...
1.1 This practice covers the calculation of low-temperature properties of asphalt binders using data from the bending beam rheometer (see Test Method D 6648) (BBR) and the direct tension tester (se...
2002-07-10
2011-04-08
1.1 This specification covers minimum requirements for cellulose fibers intended for use in fiber-reinforced concrete, and other cementitious products. <div class="SectionLevel
1.1 This practice provides recommendations for the installation of buried thermoplastic pipe used in sewers and other gravity-flow applications. These recommendations are intended to ensure a stab...
1.1 This specification covers the requirements for HFC-125 as a fire–fighting medium. 1.2 This specification does not address the fire–fighting equip This specification covers...
2011-10-14
1.1 This test method covers the determination of the percent benzene in full-range gasoline. It is applicable to concentrations from 0.1 % to 5 volume %. 1.2 This test method has not been validate...
2004-11-01
1.1 This specification covers nickel-chromium-molybdenum-tungsten (UNS N06110) in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1. 1.2 The values state...
2006-06-01
1.1 This test method covers an analytical scheme using the mass spectrometer to determine the hydrocarbon types present in virgin middle distillates 204 to 343°C (400 to 650°<
2009-10-01
1.1 This practice covers the selection and application temperatures of road tar grades in the construction and maintenance of pavements. 1.2 The values stated in SI units are to be regarded as sta...
2009-12-01
1.1 This test method covers determination of the thermal endurance of film-insulated round magnet wire in air at atmospheric pressure. It is not applicable to magnet wire with fibr
2007-05-09
1.1 This specification covers a group of general requirements common to several wrought product specifications. Unless otherwise specified in the purchase order, or in an individual specification,...
2011-04-15
1.1 This specification covers post-applied coatings, pavings, and linings for corrugated steel pipe and corrugated steel structural plate pipe, pipe-arches, and arches coated, paved, or lined with ...
1.1 1.1 This test method covers a rapid and quantitative determination of the residue in emulsified asphalts using a moisture analyzer. It is applicable to all nonsolvent-containing emulsion types....
2008-03-12
1.1 This practice covers a standard procedure for the cooling of analytical solutions such as those prepared Practices D 4901, D 4905, or D 6405. The tannin analysis results
2004-04-01
1.1 This specification covers low-melting point metal alloys and solders, including bismuth–tin, bismuth–lead, bismuth–tinThis specification covers low-melting poi...
1.1 These test methods cover the determination of two of the pore size properties of membrane filters with maximum pore sizes from 0.1 to 15.0 μm. 1.2 Test Method A presents a test meth
2003-01-01
1.1 This test method covers a vehicle test procedure to evaluate the tendency of an unleaded spark-ignition engine fuel to foul electronic port fuel injectors (PFI). <div
1.1 This practice covers the selection and use of procedures for testing primers and primer surfacers. The test methods included are listed in Table 1. 1.2 The values stated in SI units are to be r...
2005-05-15
1.1 These methods cover general procedures for the calibration of radiation detectors and the analysis of radionuclides. For each individual radionuclide, one or more of these methods may apply. 1...
2010-01-01
1.1 Purpose and Application: 1.1.1 This guide summarizes the equipment, field procedures, and interpretation methods for the assessment of the electrical properties of
2005-05-01
1.1 These test methods are intended for determining the softening point of resins (including rosin and terpene resins) and similar materials by means of the ring-and-ball apparatus. Note
2004-06-01
1.1 This test method covers the determination of iron in manganese ore in the range from 2 % to 20 %. Note 1—As used in this test method (except as related to the term <s
2011-11-18
1.1 This practice is a general guide for ambient air analyzers used in determining air quality. 1.2 The actual method, or analyzer chosen, depends on the ultimate aim of the user: whether it is for...
2005-10-01
1.1 This test method provides a method for measuring the compressive strength of compacted bituminous mixtures. It is for use with specimens weighed, batched, mixed, and fabricated in the laborator...
2009-07-01
1.1 This specification covers all cast strainers and welded strainers in services up to 150 psig and 150°F (1 MPa and 65°C). For welded strainers used in services above This s...
2010-03-01
1.1 These test methods cover the determination of (1) the resistance to deformation of compacted bituminous mixtures by measuring the lateral pressure developed when applying a vertical load by me...