21295 träffar på

Standard · ASTM ASTM A820/A820M Standard Specification for Steel Fibers for Fiber-Reinforced Concrete 1.1 This specification covers minimum requirements for steel fibers intended for use in fiber-reinforced concrete. Five types of steel fibers for this purpose are defined as pieces of smooth or def... Språk Publicerad 2011-11-18

PDF · 468 SEK

Standard · ASTM ASTM C830 Standard Test Methods for Apparent Porosity, Liquid Absorption, Apparent Specific Gravity, and Bulk Density of Refractory Shapes by Vacuum Pressure 1.1 These test methods cover the determination of the following properties of refractory shapes: 1.1.1 Apparent porosity, 1.1.2 Liquid absorption, 1.1.3 Apparent specific gravity, an Språk Publicerad 2006-06-01

PDF · 533 SEK

Standard · ASTM ASTM D1640 Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature 1.1 These test methods cover the determination of the various stages and rates of film formation in the drying or curing of organic coatings normally used under conditions of ambient room temp... Språk Publicerad 2003-12-01

PDF · 468 SEK

Standard · ASTM ASTM D4039 Standard Test Method for Reflection Haze of High-Gloss Surfaces 1.1 This test method describes a procedure for using two specular gloss measurements to obtain a haze index for high-gloss nonmetallic specimens (1-4). It is particularly useful for evaluatin... Språk Publicerad 2009-06-01

PDF · 468 SEK

Standard · ASTM ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings 1.1 This test method covers the determination of the resistance of either thermoplastic or reinforced thermosetting resin pipe, tubing, or fittings to hydraulic presssure in a short time period. Pr... Språk Publicerad 2005-05-01

PDF · 468 SEK

Standard · ASTM ASTM C969M Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric) 1.1 This practice covers procedures for testing installed precast concrete pipe sewer lines using either water infiltration or exfiltration acceptance limits to demonstrate the integrity of the in... Språk Publicerad 2002-08-10

PDF · 468 SEK

Standard · ASTM ASTM E1386 Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Solvent Extraction 1.1 This practice covers the procedure for removing small quantities of ignitable liquid residue from samples of fire debris using solvent to extract the residue. 1.2 This practice is suitable fo... Språk Publicerad 2011-05-20

PDF · 468 SEK

Standard · ASTM ASTM D6493 Standard Test Methods for Softening Point of Hydrocarbon Resins and Rosin Based Resins by Automated Ring-and-Ball Apparatus 1.1 These test methods are intended for determining the softening point of hydrocarbon resins, rosin based resins and similar materials by means of an automated ring-and-ball apparatus. Portions ... Språk Publicerad 2011-09-16

PDF · 533 SEK

Standard · ASTM ASTM F1675 Standard Practice for Life-Cycle Cost Analysis of Plastic Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits 1.1 This practice establishes a procedure for using life cycle cost (LCC) analysis techniques to evaluate alternative drainage system designs, using plastic pipe that satisfy the same functional r... Språk Publicerad 2009-08-01

PDF · 533 SEK

Standard · ASTM ASTM C1311 Standard Specification for Solvent Release Sealants 1.1 This specification describes the properties of a one-component solvent release sealant for use in building construction. These sealants are generally formulated to withstand a maximum joint mov... Språk Publicerad 2010-03-01

PDF · 468 SEK

Standard · ASTM ASTM D4122 Standard Practice for Carbon Black-Evaluation of an Industry Reference Black 1.1 This practice covers guidelines for the production and testing for uniformity of a lot of carbon black to be used as an Industry Reference Black (IRB). 1.2 The values stated in SI units are to... Språk Publicerad 2010-02-15

PDF · 533 SEK

Standard · ASTM ASTM D7201 Standard Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in the Workplace, by Phase Contrast Microscopy (with an Opt... 1.1 This practice describes the determination of the concentration of fibers, expressed as the number of such fibers per millilitre of air, using phase contrast microscopy and optionally transmiss... Språk Publicerad 2006-06-01

PDF · 767 SEK

Standard · ASTM ASTM D4655 Standard Test Methods for Sulfates in Leather (Total, Neutral, and Combined Acid) 1.1 These test methods are intended for use in determining the total, neutral, and combined acid sulfate in mineral-tanned leather. 1.2 The values stated in SI units are to be regarded as standard.... Språk Publicerad 2006-10-01

PDF · 468 SEK

Standard · ASTM ASTM D4759 Standard Practice for Determining the Specification Conformance of Geosynthetics 1.1 This practice covers a procedure for determining the conformance of geosynthetic properties to standard specifications. 1.2 This standard does not purport to address all of the safety concerns, if Språk Publicerad 2011-10-14

PDF · 533 SEK

Standard · ASTM ASTM D3885 Standard Test Method for Abrasion Resistance of Textile Fabrics (Flexing and Abrasion Method) 1.1 This test method covers the determination of the abrasion resistance of woven or nonwoven textile fabrics using the flexing and abrasion tester. 1.2 This test method applies to most woven an... Språk Publicerad 2008-03-12

PDF · 533 SEK

Standard · ASTM ASTM D6891 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine 1.1 This test method measures the ability of crankcase oil to control camshaft lobe wear for spark-ignition engines equipped with an overhead valve-train and sliding cam followers. This test method... Språk Publicerad 2010-09-17

PDF · 858 SEK

Standard · ASTM ASTM D2413 Standard Practice for Preparation of Insulating Paper and Board Impregnated with a Liquid Dielectric 1.1 This practice covers the preparation of insulating paper and board impregnated with a liquid dielectric. Where this practice states only “paper,” the same procedure Språk Publicerad 2009-10-01

PDF · 468 SEK

Standard · ASTM ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment 1.1 This specification establishes minimum performance requirements for the impact attenuation of playground surfacing materials installed within the use zone of playground equipment. 1.2 This spec... Språk Publicerad 2009-12-01

PDF · 767 SEK

Standard · ASTM ASTM G102 Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements 1.1 This practice covers the providing of guidance in converting the results of electrochemical measurements to rates of uniform corrosion. Calculation methods for converting corrosion current dens... Språk Publicerad 2010-05-01

PDF · 533 SEK

Standard · ASTM ASTM D4469 Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in an Asphalt Pavement Mixture 1.1 This practice covers equations for calculating percent asphalt absorption by the aggregate in an asphalt paving mixture, expressed as percent of the oven-dry mass of the aggregate in the paving... Språk Publicerad 2012-02-24

PDF · 468 SEK

Standard · ASTM ASTM E2329 Standard Practice for Identification of Seized Drugs 1.1 This practice describes minimum criteria for the qualitative analysis (identification) of seized drugs. 1.2 Listed are a number of analytical techniques for the identification of seized drugs... Språk Publicerad 2011-03-18

PDF · 468 SEK

Standard · ASTM ASTM D1513 Standard Test Method for Carbon Black, Pelleted—Pour Density 1.1 This test method covers the determination of the pour density of pelleted carbon blacks. 1.2&#x00a Språk Publicerad 2005-05-01

PDF · 468 SEK

Standard · ASTM ASTM D440 Standard Test Method of Drop Shatter Test for Coal 1.1 This test method of drop shatter test2 covers the determination of the relative size stab Språk Publicerad 2007-11-07

PDF · 468 SEK

Standard · ASTM ASTM D5128 Standard Test Method for On-Line pH Measurement of Water of Low Conductivity 1.1 This test method covers the precise on-line determination of pH in water samples of conductivity lower than 100 μS/cm (see Table 1 and Table 2) over the pH range of 3 to 11 (see Fig... Språk Publicerad 2009-10-01

PDF · 611 SEK

Standard · ASTM ASTM F2199 Standard Test Method for Determining Dimensional Stability of Resilient Floor Tile after Exposure to Heat 1.1 This test method covers the determination of the change in linear dimensions of resilient floor tile after exposure to heat. 1.2 The values stated in inch-pound units shall be regarded as the s... Språk Publicerad 2009-11-15

PDF · 468 SEK

Standard · ASTM ASTM D3307 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials 1.1 This specification covers melt processable molding and extrusion materials of PFA-perfluoro(alkoxy alkane) fluorocarbon resin. The materials are copolymers of TFE-fluorocarbon resins containing... Språk Publicerad 2010-09-17

PDF · 533 SEK

Standard · ASTM ASTM C965 Standard Practice for Measuring Viscosity of Glass Above the Softening Point 1.1 This practice covers the determination of the viscosity of glass above the softening point through the use of a platinum alloy spindle immersed in a crucible of molten glass. Spindle torque, de... Språk Publicerad 2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM B103/B103M Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar 1.1 This specification establishes copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rol... Språk Publicerad 2010-05-17

PDF · 533 SEK

Standard · ASTM ASTM D5542 Standard Test Methods for Trace Anions in High Purity Water by Ion Chromatography 1.1 These test methods cover the determination of trace (μg/L) levels of fluoride, acetate, formate, chloride, phosphate, and sulfate in high purity water using ion chromatography in co... Språk Publicerad 2004-06-01

PDF · 533 SEK

Standard · ASTM ASTM G30 Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens 1.1 This practice covers procedures for making and using U-bend specimens for the evaluation of stress-corrosion cracking in metals. The U-bend specimen is generally a rectangular strip which is be... Språk Publicerad 1997-04-10

PDF · 533 SEK

• < Föregående
• 651
• 652
• 653
• 654
• 655
• 656
• 657
• 658
• 659
• 660
• Nästa >