21313 träffar på

ASTM D2203
Standard · ASTM ASTM D2203

Standard Test Method for Staining from Sealants

1.1 This test method covers a laboratory procedure for determining whether a sample of sealant will cause staining of the substrate when in the contact with masonry, concrete, or stone (marble, lim...

Språk

Publicerad

2008-01-09
PDF · 468 SEK
ASTM D6064
Standard · ASTM ASTM D6064

Standard Specification for HFC-227ea, 1,1,1,2,3,3,3-Heptafluoropropane (CF3CHFCF3)

1.1 This specification covers requirements for HFC-227ea as a fire-fighting medium. 1.2 This specification does not address the fire-fighting equipment or hardware that employs HFC-227ea or the con...

Språk

Publicerad

2011-10-14
PDF · 533 SEK
ASTM D769
Standard · ASTM ASTM D769

Standard Specification for Black Synthetic Iron Oxide

1.1 This specification covers the pigment commercially known as black synthetic iron oxide. 1.2 The values s This specification details the properties and requirements for the pigment commercially...

Språk

Publicerad

2001-05-10
PDF · 468 SEK
ASTM C915
Standard · ASTM ASTM C915

Standard Specification for Precast Reinforced Concrete Crib Wall Members

1.1 This specification covers open- and closed-face precast reinforced concrete crib walls intended to act as earth-retaining structures or as protection against stream encroachment. Note This sp...

Språk

Publicerad

2010-09-17
PDF · 533 SEK
ASTM D5824
Standard · ASTM ASTM D5824

Standard Test Method for Determining Resistance to Delamination of Adhesive Bonds in Overlay-Wood Core Laminates Exposed to Heat and Water

1.1 This test method provides a procedure to determine the quality of bond between an overlay and a wood core in an adhesively bonded laminate. The quality of bond is determined by measuring the re...

Språk

Publicerad

2003-04-10
PDF · 533 SEK
ASTM D7337/D7337M
Standard · ASTM ASTM D7337/D7337M

Standard Test Method for Tensile Creep Rupture of Fiber Reinforced Polymer Matrix Composite Bars

1.1 This test method outlines requirements for tensile creep rupture testing of fiber reinforced polymer matrix (FRP) composite bars commonly used as tensile elements in reinforced

Språk

Publicerad

2012-12-20
PDF · 533 SEK
ASTM F1025
Standard · ASTM ASTM F1025

Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pr...

1.1 This guide specifically addresses the design and installation of full-encirclement-type band clamps for repair of gouges, punctures, or holes, and for reinforcement of polyethylene plastic pipe...

Språk

Publicerad

2006-05-01
PDF · 468 SEK
ASTM F1264
Standard · ASTM ASTM F1264

Standard Specification and Test Methods for Intramedullary Fixation Devices

1.1 This specification is intended to provide a characterization of the design and mechanical function of intramedullary fixation devices (IMFDs), specify labeling and material requirements, provid...

Språk

Publicerad

2007-12-05
PDF · 611 SEK
ASTM F404
Standard · ASTM ASTM F404

Standard Consumer Safety Specification for High Chairs

1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair. 1.2 This consumer safety specification is i...

Språk

Publicerad

2010-11-19
PDF · 611 SEK
ASTM A1005/A1005M
Standard · ASTM ASTM A1005/A1005M

Standard Specification for Steel Line Pipe, Black, Plain End, Longitudinal and Helical Seam, Double Submerged-Arc Welded

1.1 This specification covers double submerged-arc welded, black, plain end steel pipe for use in the conveyance of fluids under pressure. Pipe in sizes NPS 16 and larger, as given in ASME B36.10, ...

Språk

Publicerad

2004-09-01
PDF · 533 SEK
ASTM D3294
Standard · ASTM ASTM D3294

Standard Specification for PTFE Resin Molded Sheet and Molded Basic Shapes

1.1 This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses ...

Språk

Publicerad

2009-11-01
PDF · 533 SEK
ASTM D5576
Standard · ASTM ASTM D5576

Standard Practice for Determination of Structural Features in Polyolefins and Polyolefin Copolymers by Infrared Spectrophotometry (FT-IR)

1.1 This practice covers infrared procedures for determining the molecular structural features in polyolefins and polyolefin copolymers. The structural features of primary concern This p...

Språk

Publicerad

2006-09-01
PDF · 468 SEK
ASTM C1182
Standard · ASTM ASTM C1182

Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation

1.1 This test method covers the determination of the particle size distribution of alumina in the range from 0.1 to 20 &#x03BC;m having a median particle diameter from 0.5 to 5.0 &#x03BC;</

Språk

Publicerad

2009-01-01
PDF · 468 SEK
ASTM F2055
Standard · ASTM ASTM F2055

Standard Test Method for Size and Squareness of Resilient Floor Tile by Dial Gage Method

1.1 This test method covers the determination of both dimensions (length and width) and squareness of resilient floor tile. This test method is intended for use with square tiles ranging from a no...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM D7048
Standard · ASTM ASTM D7048

Standard Guide for Applying Statistical Methods for Assessment and Corrective Action Environmental Monitoring Programs

1.1 The scope and purpose of this guidance is to present a variety of statistical approaches for assessment, compliance and corrective action environmental monitoring programs. Although the methods...

Språk

Publicerad

2004-05-01
PDF · 611 SEK
ASTM A751
Standard · ASTM ASTM A751

Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

1.1 These test methods, practices, and terminology cover definitions, reference methods, practices, and guides relating to the chemical analysis of steel, stainless steel, and related alloys. It in...

Språk

Publicerad

2011-12-16
PDF · 533 SEK
ASTM G6
Standard · ASTM ASTM G6

Standard Test Method for Abrasion Resistance of Pipeline Coatings (Withdrawn 2007)

1.1 This test method of accelerated test is a procedure for determining the relative resistance of steel pipeline coatings to abrasion by a slurry of coarse abrasive and water. The method is intend...

Språk

Publicerad

1998-07-10

Upphävd

2007-03-22
PDF · 468 SEK
ASTM D1739
Standard · ASTM ASTM D1739

Standard Test Method for Collection and Measurement of Dustfall (Settleable Particulate Matter)

1.1 This test method covers a procedure for collection of dustfall and its measurement. This test method is not appropriate for determination of the dustfall rate in small areas affected by specifi...

Språk

Publicerad

2004-10-01
PDF · 468 SEK
ASTM D3823
Standard · ASTM ASTM D3823

Standard Practice for Determining Ticket Numbers for Sewing Threads

1.1 This practice establishes standard ticket numbers for sewing thread regardless of fiber content or type of thread. 1.2 The values stated in inch-pound units are to be regarded as the standard; ...

Språk

Publicerad

2007-01-01
PDF · 468 SEK
ASTM D1971
Standard · ASTM ASTM D1971

Standard Practices for Digestion of Water Samples for Determination of Metals by Flame Atomic Absorption, Graphite Furnace Atomic Absorption, Plasm...

1.1 Most atomic absorption and plasma emission spectroscopy, and plasma-mass spectrometric test methods require that the metals of interest be dissolved in a liquid phase before being introduced in...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM E2234
Standard · ASTM ASTM E2234

Standard Practice for Sampling a Stream of Product by Attributes Indexedby AQL

1.1 This standard establishes lot or batch sampling plans and procedures for inspection by attributes using MIL-STD-105E as a basis for sampling a steady stream of lots indexed by AQL. 1.2 Thi...

Språk

Publicerad

2009-11-01
PDF · 923 SEK
ASTM A701/A701M
Standard · ASTM ASTM A701/A701M

Standard Specification for Ferromanganese-Silicon

1.1 This specification covers a manganese-silicon alloy. 1.2 Units&#8212;The values stated in either SI units or inch-pound units are to be regarded separately as st This specification covers f...

Språk

Publicerad

2011-05-20
PDF · 468 SEK
ASTM D4093
Standard · ASTM ASTM D4093

Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials

1.1 This test method covers measurements of direction ofprincipal strains, &#x03B5;1 and &#x03B5;2, and the photoelastic retardation, &#x

Språk

Publicerad

2005-07-01
PDF · 611 SEK
ASTM D6620
Standard · ASTM ASTM D6620

Standard Practice for Asbestos Detection Limit Based on Counts

1.1 This practice presents the procedure for determining the detection limit (DL) for measurements of fibers or structures using microscopy methods. 1.2 This practice applies to samples of air th...

Språk

Publicerad

2007-01-11
PDF · 611 SEK
ASTM D3567
Standard · ASTM ASTM D3567

Standard Practice for Determining Dimensions of &ldquo;Fiberglass&rdquo; (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings

1.1 This practice covers the determination of outside diameter, inside diameter, total wall thickness, reinforced wall thickness, liner thickness (where applicable), and length dimensions of &...

Språk

Publicerad

2007-01-11
PDF · 468 SEK
ASTM D3774
Standard · ASTM ASTM D3774

Standard Test Method for Width of Textile Fabric

1.1 This test method covers the measurement of the width of fabrics, pile or napped surface width, or both. The method is applicable to full rolls, bolts of fabric, and short specimens removed from...

Språk

Publicerad

2008-07-01
PDF · 468 SEK
ASTM F420
Standard · ASTM ASTM F420

Standard Test Method for Access Depth Under Furniture of Vacuum Cleaners

1.1 This test method covers the measurement of the operational ability of the vacuum cleaner, expressed as the access depth for a given furniture clearance above the floor. 1.2 This test method ca...

Språk

Publicerad

2004-08-01
PDF · 468 SEK
ASTM F1438
Standard · ASTM ASTM F1438

Standard Test Method for Determination of Surface Roughness by Scanning Tunneling Microscopy for Gas Distribution System Components

1.1&#x00a0;The purpose of this test method is to define a method for analyzing the surface texture of the above-mentioned components using a scanning tunneling microscope (STM). STM is a

Språk

Publicerad

1999-06-10
PDF · 533 SEK
ASTM A368
Standard · ASTM ASTM A368

Standard Specification for Stainless Steel Wire Strand

1.1 This specification covers stainless steel wire strand composed of a multiplicity of round wires and suitable for use as guy wires, overhead ground wires, and similar purposes. 1.2 The values ...

Språk

Publicerad

2009-05-01
PDF · 468 SEK
ASTM D3969
Standard · ASTM ASTM D3969

Standard Test Method for Zirconium in Paint Driers by EDTA Method

1.1&#x00a0;This test method covers the titrimetric determination of zirconium in zirconium driers used in the coatings industry and utilizes the disodium salt of ethylenediaminetetraaceti

Språk

Publicerad

2006-06-01
PDF · 468 SEK
Förfina din sökning genom att visa:
...som handlar om:

Ämnesområden (0)

Avbryt

Branscher (0)

Avbryt

Syfte (0)

Avbryt

Material (0)

Avbryt
Visa varukorgen Fortsätt handla 0
Varukorgen Stäng
Annonstext