1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements. 1.2 When refere...
2010-03-01
1.1 This test method covers drop test procedures to measure rope rescue belay system performance. It applies only to belay systems consisting of an untensioned rope connecting the load to an anchor...
2005-07-01
1.1 This test method covers the determination of the heat capacity of liquids and solids. It is applicable to liquids and solids that are chemically compatible with stainless steel, that have a va...
2009-10-01
1.1 This test method covers a suitable means of obtaining the thermal neutron fluence rate, or fluence, in well moderated nuclear reactor environments where the use of cadmium, as a thermal neutron...
2010-01-01
1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of allo...
2006-05-01
1.1 This specification covers aluminum-alloy (Note 1) die forgings, hand forgings, and rolled ring forgings as shown in Table 2, Table 3 and Table 4in Section 10 for heat-treatable alloy forgings s...
2009-09-01
1.1 This guide covers the evaluation and selection of escort vessels that are to be used to escort ships transiting confined waters. The purpose of the escort vessel is to limit the uncontrolled mo...
2009-11-01
1.1 This practice is intended to assist in the preparation of formal plans for contamination control, especially of aerospace critical surfaces. Requirements may be established at the systems level...
2009-04-01
1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) plastic hot- and cold-water tubing and distribution systems components made in one standard dimension ...
2010-09-17
1.1 This specification establishes requirements for safety covers for swimming pools, spas, hot tubs, and wading pools (hereinafter referred to as pools, unless otherwise specified). When correctly...
1991-01-01
1.1 This specification covers solid precast segmental concrete masonry units made from hydraulic cement, water, and suitable mineral aggregates, with or without the inclusion of other materials. ...
2012-02-24
1.1 This test method covers qualitative determination of the acid resistance of ceramic decorations on returnable beer and beverage containers, to assure the necessary durability of the decoration....
2004-10-01
1.1 This specification covers electronic instruments intended for intermittent monitoring of patient temperatures. 1.2 This specification does not cover infrared thermometers. Specification This sp...
1.1 This practice covers the selection and proportioning of soils and emulsified or cutback asphalts and the fabrication of 100-mm [4-in.] diameter by 65-mm [2.5-in.] high test specimens. 1.2 All o...
2012-03-23
1.1 This specification covers the requirements for titanium alloy forgings for surgical implants, in the alpha plus beta condition, when the material forged conforms to Specifications This specific...
2012-01-20
1.1 This test method covers the determination of the apparent viscosity of hot melt adhesives and coating materials compounded with additives and having apparent viscosities up to 200 000 millipas...
1.1 This test method determines the quantity of linear units of a foam sealant having a specified bead diameter that may be obtained from a single can of aerosol product. Four (4) cans are require...
1.1 This test method covers the determination of total carbon (TC), inorganic carbon (IC), and total organic carbon (TOC) in water in the range from 10 to 1000 μg/L of carbon. This meth...
1.1 This dye-penetrant test method covers a means of evaluating solid fiberglass all-roving reinforced pultruded rod or bar stock for longitudinal wicking. There are generally three mechanisms that...
1.1 This practice covers a policy (“the policy”) for digital certificates that support the authentication, authorization, confidentiality, integrity, and nonrepudiatio
2002-11-10
1.1 This specification covers a wrought alloy containing gold and copper in the form of wire, rod, strip, and tubing for electrical contacts. 1.2 The values stated in inch-pound units are to be re...
2006-06-01
1.1 These test methods cover procedures used in determining the ash content of adhesives. This standard is intended as a replacement for Method 4032.1 of Federal Test Method Standard 175B, &...
2005-10-01
1.1 This specification covers flexible crosslinked chlorinated polyolefin heat-shrinkable tubing used for electrical insulating purposes. It is supplied in an expanded form and will shrink to the ...
2011-09-16
1.1 This guide covers minimum requirements for the scope of performance of a water rescuer I who may be responsible for the initial on scene evaluation, performing land based water rescues, and pro...
2007-12-05
1.1 These test methods cover the testing of silicone fluids for use in transformers, capacitors, and electronic assemblies as an insulating or cooling medium, or both. These method
2004-12-01
1.1 The sound isolation between two spaces in a building is determined by a combination of the direct transmission through the nominally separating building element (as normally measured in a labor...
1.1 This test method determines and standardizes an unextended and extended capacity for backpacks and related bags. Related bags include lumbar packs, soft rucksacks, internal and external frame p...
1.1 These methods offer a means for controlling the effectiveness of the etchant which is normally used for preparing the surface of aluminum alloys for subsequent adhesive bonding. As the etchant ...
2004-04-01
1.1 This test method covers the determination of the tensile properties of “as produced” elastomeric yarns made from natural rubber, spandex or other elastomers, using
2007-01-01
1.1 This specification covers refined antimony in ingot, pig, or cake form. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathemati...
2007-01-11