1.1 This test method describes the determination of the ash content of pulp, paper, and paper products by ignition at two different temperatures:1.1.1 Method A—Ash content upon ignition a...
1997-12-10
2009-09-01
1.1 This test method employs the signal-to-noise ratio to determine the sensitivity of a fluorescence measuring system in testing for the limit of detection (LOD) of quinine sulfate dihydrate in so...
2009-10-01
1.1 This test method covers the sampling, preparation of specimens, and determination of the absorption of architectural cast stone. 1.2 This test method describes two procedures: (1) cold wate
2003-04-10
1.1 This test method covers the use of an Image Quality Indicator (IQI) system to determine the relative quality of radiographic images produced by direct, thermal neutron radiographic examination...
2005-06-01
1.1  This specification covers joints for plastic pipe systems intended for drain, and gravity sewerage pipe at internal or external pressures less than 25-ft head using flexible w This ...
2008-03-12
1.1 These test methods cover the determination of acidity or alkalinity of all types of water. Three test methods are given as follows: <td align="left"
2011-05-20
1.1 This test method covers the distillation of industrial aromatic hydrocarbons and related materials of relatively narrow boiling ranges from 30 to 250°C. 1.2 The values sta
2011-09-16
1.1 This guide covers the selection of procedures commonly used to establish a measurement of horizontal position during investigations of surface water bodies that are as follows
2007-09-05
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below. This specification...
1.1 This test method covers the determination of the total amount of olefins in blended motor gasolines and gasoline blending stocks by supercritical-fluid chromatography (SFC). Results are express...
2011-04-15
1.1 This test method covers a laboratory procedure for determining the strength and characteristics of the peel properties of a cured-in-place elastomeric joint sealant, single- or multicomponent, ...
2010-10-15
1.1 These test methods cover the performance of pallets and related structures, functioning as skids, bases, platforms, and bins in materials handling and shipping. Their use facilitates the protec...
1998-01-01
1.1 This specification covers elastomeric flexible hinge finger total joint implants, used with and without metal grommets in the reconstruction of the metacarpophalangeal (MCP) and proximal interp...
2003-11-01
1.1 This test method covers procedures for testing freshwater organisms in the laboratory to evaluate the toxicity of contaminants associated with whole sediments. Sediments may be collected from ...
2005-03-01
1.1 This specification covers high hardenability modifications of high-carbon bearing quality steel to be used in the manufacture of antifriction bearings. 1.2 Supplementary requirements of an o...
1.1 This specification covers apparatus used in Test Method D95 and other simil This specification covers the design and dimensional requirements for the assembly that comprise the laboratory appar...
2007-11-01
1.1 This test method describes calibration of the length change (deflection) measurement or thermal expansion of thermomechanical analyzers (TMA) within the temperature range from -150 to 1000 &am...
1.1 This test method covers the quantitative determination of the volatile matter (including water) present in vinyl chloride resins.1.2 The values stated in SI units are to be regarded as standard...
2011-10-14
1.1 This test method covers a routine standardized procedure for determining the linear drying shrinkage of concrete masonry units or related concrete units under specified accelerated drying cond...
1.1 These test methods describe the use of the Karl Fischer (KF) titration for determination of water in halogenated organic solvents and mixtures thereof. Water concentrations from 2 to 1000 ppm ...
2006-06-01
1.1 This test method covers procedures for conducting laboratory bench-scale friction tests of materials, coatings, and surface treatments intended for use in piston rings and cylinder liners in di...
2011-06-17
1.1 This test method covers procedures for testing concrete pipe sewerlines, when using the negative air pressure (vacuum) test method to demonstrate the integrity of the installed material and the...
2002-08-10
1.1 This test method covers the determination of the creep of molded concrete cylinders subjected to sustained longitudinal compressive load. This test method is limited to concrete in which the m...
1.1 This test method covers procedures for measurement of the solubility of organic compounds in water. Three procedures are described which will work over a variety of solubility ranges. These pro...
2008-02-01
2013-03-15
1.1 This practice describes a procedure for developing precautionary labels for ceramic art materials and provides hazard and precautionary statements based upon knowledge that exists in the scien...
2010-08-20
1.1 This test method covers the determination of the percentage of mature fibers in a sample of loose, chemically untreated cotton fibers, whether taken before processing or unravelled from a texti...
1.1 This test method covers the determination of the concentration of technetium-99 in urine using inductively coupled plasma-mass spectrometry (ICP-MS). This test method can be used to support ura...
2006-01-01
2011-06-01
1.1 This practice covers typical equipment and methods for collecting samples of consolidated solids in drums or similar containers. These methods are adapted specifically for samp
2007-01-11
1.1 This specification covers pearlitic malleable iron castings for general engineering usage at temperatures from normal ambient to approximately 750°F [400°C]. This specific...
2009-05-01
1.1 This practice covers methods for testing the physical properties of mechanical (passive) security seals. Where appropriate, the various tests include particular apparatus or procedural specific...
2004-09-01