21291 träffar på

Standard · ASTM ASTM F2579 Standard Specification for Amorphous Poly(lactide) and Poly(lactide-co-glycolide) Resins for Surgical Implants 1.1 This specification covers virgin amorphous poly(lactide) homopolymer and poly(lactide-co-glycolide) copolymer resins intended for use in surgical implants. The poly(dl-lactide) homopolymers cov... Språk Publicerad 2011-05-20

PDF · 611 SEK

Standard · ASTM ASTM D6550 Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography 1.1 This test method covers the determination of the total amount of olefins in blended motor gasolines and gasoline blending stocks by supercritical-fluid chromatography (SFC). Results are express... Språk Publicerad 2011-04-15

PDF · 533 SEK

Standard · ASTM ASTM C1491 Standard Specification for Concrete Roof Pavers 1.1 This specification covers concrete roof pavers that are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials, for use as ... Språk Publicerad 2012-02-24

PDF · 468 SEK

Standard · ASTM ASTM D516 Standard Test Method for Sulfate Ion in Water 1.1 This turbidimetric test method covers the determination of sulfate in water in the range from 5 to 40 mg/L of sulfate ion (SO4&#x2212;&#x2212;). <p id=" Språk Publicerad 2011-10-14

PDF · 468 SEK

Standard · ASTM ASTM D1456 Standard Test Method for Rubber Property—Elongation at Specific Stress 1.1 This test method covers determination of the elongation of soft vulcanized rubber compounds under a specified stress. 1.2 This standard does not purport to address all of the safety concerns, if a Språk Publicerad 2010-01-01

PDF · 533 SEK

Standard · ASTM ASTM D6547 Standard Test Method for Corrosiveness of Lubricating Fluid to Bimetallic Couple 1.1 This test method covers the corrosiveness of hydraulic and lubricating fluids to a bimetallic galvanic couple. Note 1—This test method replicates Fed-Std No. 791, Meth Språk Publicerad 2005-05-01

PDF · 468 SEK

Standard · ASTM ASTM D1070 Standard Test Methods for Relative Density of Gaseous Fuels 1.1 These test methods cover the determination of relative density of gaseous fuels, including liquefied petroleum gases, in the gaseous state at normal temperatures and pressures. The test methods... Språk Publicerad 2003-05-10

PDF · 533 SEK

Standard · ASTM ASTM D5401 Standard Test Method for Evaluating Clear Water Repellent Coatings on Wood 1.1 This test method evaluates the effectiveness of clear water repellent coatings on wood before or after exterior exposure. 1.2 Intralaboratory results with this test method can be used to co... Språk Publicerad 2008-06-01

PDF · 468 SEK

Standard · ASTM ASTM C538 Standard Test Method for Color Retention of Red, Orange, and Yellow Porcelain Enamels 1.1 This test method covers only porcelain enamels containing the cadmium-sulfide or cadmium sulfo-selenide types of pigments. The purpose of the test is to detect those red, yellow, orange, and s... Språk Publicerad 2004-08-01

PDF · 468 SEK

Standard · ASTM ASTM E1078 Standard Guide for Specimen Preparation and Mounting in Surface Analysis 1.1 This guide covers specimen preparation and mounting prior to, during, and following surface analysis and applies to the following surface analysis disciplines: 1.1.1 Auger electron spectroscopy... Språk Publicerad 2009-05-01

PDF · 533 SEK

Standard · ASTM ASTM F148 Standard Test Method for Binder Durability of Cork Composition Gasket Materials 1.1&#x00a0;This test method covers three procedures for determination of the binder durability of cork-containing materials. <a nam Språk Publicerad 2002-10-10

PDF · 468 SEK

Standard · ASTM ASTM D5094/D5094M Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures 1.1 These test methods may demonstrate container/closure integrity with threaded or lug-style closures by the determination of gross leaks in rigid and semi-rigid containers (up to 4 L [1.06 g]). S... Språk Publicerad 2009-10-01

PDF · 468 SEK

Standard · ASTM ASTM D3280 Standard Test Methods for Analysis of White Zinc Pigments 1.1 These test methods cover procedures for the analysis of white zinc pigments. 1.2 The analytical procedures appear in the following order:<table summary="TABLE 1" frame="void" id="n00001"... Språk Publicerad 2004-11-01

PDF · 533 SEK

Standard · ASTM ASTM C1426 Standard Practices for Verification and Calibration of Polarimeters 1.1 Polarimeters and polariscopes used for measuring stress in glass are described in Test Methods F218, This practice covers the standards for the verification and calibration of polarimeters requ... Språk Publicerad 2009-11-01

PDF · 468 SEK

Standard · ASTM ASTM D4887/D4887M Standard Practice for Preparation of Viscosity Blends for Hot Recycled Bituminous Materials 1.1 This practice covers the procedure for preparation of hot recycled bituminous blends for testing in the laboratory. The procedure involves an iterative trial blend process followed by the pre... Språk Publicerad 2011-09-16

PDF · 468 SEK

Standard · ASTM ASTM D4614 Standard Specification for Ethyl Acetate (All Grades) 1.1 This specification covers the various grades of ethyl acetate suitable for use as solvents in paint and related coatings. 1.2 The values stated in SI units are to be regarded as standard. No ... Språk Publicerad 2011-12-16

PDF · 468 SEK

Standard · ASTM ASTM F1513 Standard Specification for Pure Aluminum (Unalloyed) Source Material for Electronic Thin Film Applications 1.1 This specification covers pure aluminum metal (unalloyed) for use in evaporation sources and sputtering targets. This material is intended as a raw material for electronic applications. The mat... Språk Publicerad 1999-12-10

PDF · 468 SEK

Standard · ASTM ASTM D2221 Standard Test Method for Creep Properties of Package Cushioning Materials 1.1 This test method covers the determination of creep properties of package cushioning materials. It is applicable to materials available in bulk, sheet, or molded form used for the cushioning of ... Språk Publicerad 2001-09-10

PDF · 533 SEK

Standard · ASTM ASTM D5051 Standard Test Method for Rubber Compounding Materials—Benzothiazyl Disulfide (MBTS)—Assay 1.1 This test method covers the determination of assay of benzothiazyl disulfide (MBTS). It is based on a titration of free iodine liberated upon reduction of MBTS, with potassium iodide (KI) in ac... Språk Publicerad 2007-01-11

PDF · 468 SEK

Standard · ASTM ASTM F610/F610M Standard Test Method for Evaluating the Quality of Molded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion Technique 1.1 This test method covers a procedure for evaluating the quality of molded poly(vinyl chloride) (PVC) plastic pipe fittings after exposure to heat. 1.2 The values stated in either SI units or i... Språk Publicerad 2010-05-17

PDF · 468 SEK

Standard · ASTM ASTM C425 Standard Specification for Compression Joints for Vitrified Clay Pipe and Fittings 1.1 This specification covers materials and test requirements for compression joints for vitrified clay pipe and fittings. See Specification C 700 for pipe specifications. The test requirements a... Språk Publicerad 2009-09-01

PDF · 468 SEK

Standard · ASTM ASTM E1034 Standard Specification for Nuclear Facility Transient Worker Records 1.1 This specification covers the required content and provides retention requirements for records needed for in-processing of nuclear facility transient workers. This specification cove... Språk Publicerad 2008-01-01

PDF · 533 SEK

Standard · ASTM ASTM C1075 Standard Practices for Sampling Uranium-Ore Concentrate 1.1 These practices are intended to provide the nuclear industry with procedures for obtaining representative bulk samples from uranium-ore concentrates (UOC) (see Specification These practices ar... Språk Publicerad 2011-04-15

PDF · 533 SEK

Standard · ASTM ASTM F793 Standard Classification of Wall Covering by Use Characteristics 1.1 This classification covers the classification of wall covering by use characteristics, that is, according to its serviceability in use, recognizing that certain wall covering is designed prima... Språk Publicerad 2010-05-17

PDF · 533 SEK

Standard · ASTM ASTM E715 Standard Specification for Gravity-Convection and Forced-Circulation Water Baths 1.1 This specification covers the performance requirements for general-purpose water baths ordinarily used in testing operations. It is applicable to gravity-convection and forced-circulation water... Språk Publicerad 2011-12-01

PDF · 468 SEK

Standard · ASTM ASTM D5009 Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions 1.1 This test method covers the evaluation and comparison of the transfer efficiency of spray-applied coatings under controlled laboratory conditions. 1.2 This test method has been shown to yield ... Språk Publicerad 2005-05-15

PDF · 468 SEK

Standard · ASTM ASTM C946 Standard Practice for Construction of Dry-Stacked, Surface-Bonded Walls 1.1 This practice covers material, workmanship, and construction procedures for applying surface bonded mortar to both sides of dry stacked concrete masonry units. It does not include grout, reinfo... Språk Publicerad 2011-04-15

PDF · 468 SEK

Standard · ASTM ASTM E964 Standard Practice for Measuring Benefit-to-Cost and Savings-to-Investment Ratios for Buildings and Building Systems 1.1 This practice covers a procedure for calculating and interpreting benefit-to-cost ratios (BCR) and savings-to-investment ratios (SIR) as an aid for making building-related decisions. 1.2 A bas... Språk Publicerad 2006-04-01

PDF · 533 SEK

Standard · ASTM ASTM D7295 Standard Practice for Sampling and Determination of Hydrogen Cyanide (HCN) in Combustion Effluents and Other Stationary Sources 1.1 This practice is used to determine the concentration of gaseous hydrogen cyanide (HCN) from any combustion device or atmosphere where cyanide may be present. While primarily designed for the me... Språk Publicerad 2011-05-20

PDF · 533 SEK

Standard · ASTM ASTM D2209 Standard Test Method for Tensile Strength of Leather 1.1 This test method covers the determination of the load required to rupture a leather test specimen having a ½-in. (12.7-mm) width. The load to rupture divided by the original unstre... Språk Publicerad 2004-09-01

PDF · 468 SEK

• < Föregående
• 624
• 625
• 626
• 627
• 628
• 629
• 630
• 631
• 632
• 633
• Nästa >