1.1 This specification covers the requirements for chromium-carbon bearing quality stainless steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary Requirements of an opt...
2009-10-01
1.1 This specification covers four types of moderately volatile hydrocarbon solvents, mainly aliphatic in composition and normally petroleum distillates. These solvents are used pr This ...
2007-09-05
1.1 This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque s...
2011-09-16
1.1 This practice shall apply to all fuel alcohol manufacturing facilities (FAMF) as defined in Terminology E 1705. This specification is primarily intended for, but not exclusively limited to ferm...
2006-02-01
2009-09-01
1.1 This test method specifies a laboratory procedure for the determination of the water retention curve (or moisture storage capacity) of porous building materials at very high relative humidity (...
2009-05-01
1.1 This test method covers a procedure for detecting the presence of acetone in methanol in amounts greater than 0.003 weight %. 1.2 The values stated in SI units are to be regarded as standard. N...
2005-01-01
2011-06-01
1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels. This test method uses a Ford Ranger 2.3 L...
2004-05-01
1.1 This test method provides an indirect measurement of the viscosity of clay slurries using a funnel (Marsh Funnel) and a graduated cup of specific dimensions. This test method provides a practic...
1.1 This test method covers the determination of dielectric strength of solid electrical insulating materials under simulated-lightning impulse conditions. <div class="Se
2004-03-01
1.1 This practice establishes criteria for the design, manufacture, and operations of bumper boats. These are boats used to bump into each other intentionally as directed by drivers as a form of en...
2011-05-20
1.1 This test method covers the X-ray emission spectrometric analysis of limestone, quicklime, hydrated lime, and hydraulic lime using wavelength dispersive instruments.
2006-02-15
1.1 This test method covers the quantitative determination of the susceptibility of metallic materials to hydrogen embrittlement, when exposed to high pressure gaseous hydrogen. 1.2 The values stat...
2006-04-01
1.1 This test method covers two procedures for the determination of the pour point temperatures of crude oils down to −36°C. Procedure A provides a measure of the maxim
1.1 This practice covers the technical training and experience of laboratory testing personnel and identifies the minimum technical requirements for laboratory equipment used in testing of hydrauli...
2009-06-01
1.1 This test method covers obtaining, preparing, and testing cores drilled from shotcrete for length, compressive strength, or splitting tensile strength determinations.</div
1.1 This specification covers nickel-chromium-iron-molybdenum-tungsten alloy UNS N06920 in the form of rolled plate, sheet, and strip for general corrosion service. 1.2 The following products...
2007-02-07
1.1 Purpose—The purpose of this document is to provide a standard guide for estimating costs and liabilities for environmental matters. Many possible
2006-11-01
1.1 This specification covers performance requirements for head protection used for training and competition in martial arts such as karate, wushu, and taekwondo, where normal contact between par...
2009-11-01
1.1 This test method covers the mechanical performance of insulating varnishes after exposure to various chemicals. 1.2 The values stated in SI units are to be regarded as standard. No other units ...
2005-09-01
1.1 This test method is intended for use in determining the unconfined tension creep and creep rupture behavior of geosynthetics at constant temperature when subjected to a sustain
1.1 This specification covers zinc-5 % aluminum-mischmetal (Zn-5A1-MM) alloy-coated steel chain-link fence fabric, Zn-5A1-MM alloy-coated, before weaving. 1.2 The values stated in inch-pound units ...
2010-09-17
1.1 This fire-test-response test methods describe small-scale laboratory procedures for determining the comparative burning characteristics of solid plastic materials that, due to specimen thinness...
1.1 These alternative test methods cover the indicator procedure for determining the total, primary, secondary, and tertiary amine values of fatty amines. These procedures are not applicable to fat...
1992-01-01
2007-03-20
1.1 This practice covers a procedure that is used to determine the fusion temperature of dry electrostatic heat-fixing toners using a micro hot stage. 1.2 This standard does not purport to address al
2006-06-01
1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products. 1.2 This test method provides corrosion resul...
1.1 This specification covers seamless pipe and tube of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS ...
2011-04-15
1.1 This test method covers the measurement of a longitudinal profile of a travelled surface using a static level for the purpose of obtaining a road roughness index. This test method is suitable f...
2005-06-01
1.1 This practice covers procedures for conducting laboratory corrosion tests in soils to evaluate the corrosive attack on engineering materials. 1.2 This practice covers specimen selection and pre...
2004-11-01
1.1 These test methods cover the fracture toughness, KIc, determination of advanced ceramics at ambient temperature. The methods determine KIpb (precracked beam t
2011-03-18
1.1 This fire-test-response standard determines fire properties related to piloted ignition of a vertically oriented specimen exposed to an external graduated radiant heat flux as shown in . This t...
2011-07-01