21328 träffar på

Standard · ASTM ASTM D1635

Standard Test Method for Flexural Strength of Soil-Cement Using Simple Beam with Third-Point Loading

1.1 This test method covers the determination of the flexural strength of soil-cement by the use of a simple beam with third-point loading. Note 1—For methods of molding soil-cement speci...

Språk

Publicerad

2006-05-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM D4945

Standard Test Method for High-Strain Dynamic Testing of Piles

1.1 This dynamic test method covers the procedure for applying an axial impact force with a pile driving hammer or a large drop weight that will cause a relatively high strain at the top of an indi...

Språk

Publicerad

2008-10-01

Upphävd

2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM D5967

Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). This te...

Språk

Publicerad

2011-09-16

Upphävd

2012-04-15

PDF · 767 SEK

Standard · ASTM ASTM D6121

Standard Test Method for Evaluation of Load-Carrying Capacity of Lubricants Under Conditions of Low Speed and High Torque Used for Final Hypoid Dri...

1.1 This test method is commonly referred to as the L-37 test. This test method covers a test procedure for evaluating the load-carrying, wear, and extreme pressure properties of a gear lubrican...

Språk

Publicerad

2011-12-16

Upphävd

2012-04-15

PDF · 611 SEK

Standard · ASTM ASTM D6984

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine

1.1 This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening, varnish deposition, oi...

Språk

Publicerad

2011-08-25

Upphävd

2012-04-15

PDF · 858 SEK

Standard · ASTM ASTM E1014

Standard Guide for Measurement of Outdoor A-Weighted Sound Levels

1.1 This guide covers the measurement of A-weighted sound levels outdoors at specified locations or along particular site boundaries, using a general purpose sound-level meter. 1.2 Three distinct t...

Språk

Publicerad

2008-08-06

Upphävd

2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM E1503

Standard Test Method for Conducting Outdoor Sound Measurements Using a Digital Statistical Sound Analysis System

1.1 This test method covers the measurement of outdoor sound levels at specific locations using a digital statistical sound analysis system and a formal measurement plan.1.1.1 This test method prov...

Språk

Publicerad

2007-02-07

Upphävd

2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM F1334

Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners

1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister, combination vacuum cleaners, and central vacuum cleaner motorized nozzles inten...

Språk

Publicerad

2012-02-24

Upphävd

2012-06-01

PDF · 533 SEK

Standard · ASTM ASTM F1868

Standard Test Method for Thermal and Evaporative Resistance of Clothing Materials Using a Sweating Hot Plate

1.1 This test method covers the measurement of the thermal resistance and the evaporative resistance, under steady-state conditions, of fabrics, films, coatings, foams, and leathers, including mult...

Språk

Publicerad

2009-02-15

Upphävd

2012-06-01

PDF · 533 SEK

Standard · ASTM ASTM F2012

Standard Consumer Safety Performance Specification for Stationary Activity Centers

1.1 This consumer safety performance specification covers performance requirements, test methods and marking requirements to promote safe use of a stationary activity center by an occupant. 1.2 Thi...

Språk

Publicerad

2012-02-24

Upphävd

2012-06-01

PDF · 533 SEK

Standard · ASTM ASTM F2479

Standard Guide for Specification, Purchase, Installation and Maintenance of Poured-In-Place Playground Surfacing

1.1 This guide covers information with regard to the design, manufacture, installation, and maintenance of poured-in-place playground surfaces. Note 1—This document is a g

Språk

Publicerad

2012-02-24

Upphävd

2012-05-15

PDF · 533 SEK

Standard · ASTM ASTM D5469

Standard Guide for Application of New Spray Applied Polyurethane Foam and Coated Roofing Systems

1.1 This guide covers the application of new roofing systems consisting of spray applied polyurethane foam insulation, elastomeric protective coatings, and optional mineral granules. This guide doe...

Språk

Publicerad

2005-05-01

Upphävd

2012-06-01

PDF · 533 SEK

Standard · ASTM ASTM D4479

Standard Specification for Asphalt Roof Coatings—Asbestos-Free

1.1 This specification covers asbestos-free asphalt roof coatings of brushing or spraying consistency.1.2 The following precautionary caveat pertains only to the test method portion, Section 8, of ...

Språk

Publicerad

2007-09-05

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM E967

Standard Practice for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers

1. Scope 1.1 This test method describes the temperature calibration of differential thermal analyzers and differential scanning calorimeters over the temperature range from 40 to +2500 C.1.2 1.3 T...

Språk

Publicerad

2008-09-01

PDF · 468 SEK

Standard · ASTM ASTM A203/A203M

Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel

1.1 This specification covers nickel-alloy steel plates intended primarily for welded pressure vessels. 1.2 Plates under this specification are available with four strength levels and two nickel ...

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM ISO/ASTM 51276

Standard Practice for Use of a Polymethylmethacrylate Dosimetry System

1.1 This practice covers procedures for using hermetically-sealed polymethylmethacrylate (PMMA) dosimeters for measuring absorbed dose in materials irradiated by photons or electrons in terms of ab...

Språk

Publicerad

2002-01-22

Upphävd

2010-06-01

PDF · 533 SEK

Standard · ASTM ASTM A123/A123M

Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

1.1 This specification covers the requirements for zinc coating (galvanizing) by the hot-dip process on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, ...

Språk

Publicerad

2008-11-05

Upphävd

2009-05-01

PDF · 533 SEK

Standard · ASTM ASTM A123/A123M

Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

1.1 This specification covers the requirements for zinc coating (galvanizing) by the hot-dip process on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, ...

Språk

Publicerad

2009-07-08

Upphävd

2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM A182/A182M

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

1.1 This specification covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions...

Språk

Publicerad

2008-05-14

Upphävd

2009-06-01

PDF · 611 SEK

Standard · ASTM ASTM A182/A182M

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

1.1 This specification covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions...

Språk

Publicerad

2010-05-01

Upphävd

2010-11-01

PDF · 611 SEK

Standard · ASTM ASTM A204/A204M

Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum

1.1 This specification covers molybdenum-alloy steel plates, intended particularly for welded boilers and other pressure vessels. 1.2 Plates under this specification are available in three grade...

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM A225/A225M

Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-Nickel

1.1 This specification covers manganese-vanadium-nickel alloy steel plates intended primarily for welded layered pressure vessels. 1.2 Plates under this specification are available in two grades...

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM A285/A285M

Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength

1.1 This specification covers carbon steel plates of low- and intermediate-tensile strengths which may be made by killed, semi-killed, capped, or rimmed steel practices at the producer's option....

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM A302/A302M

Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel

1.1 This specification covers manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates intended particularly for welded boilers and other pressure vessels. 1.2 Plates under this...

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM A455/A455M

Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength Manganese

1.1 This specification covers high-tensile strength carbon-manganese steel plates intended for welded pressure vessels. 1.2 This steel is usually made to a semi-killed or capped deoxidation prac...

Språk

Publicerad

2007-11-01

Upphävd

2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM A490M

Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)

1.1 This specification covers two types of quenched and tempered alloy steel, metric heavy hex structural bolts having a tensile strength of 1040 to 1210 MPa. 1.2 These bolts are intended for use ...

Språk

Publicerad

2012-02-24

Upphävd

2012-04-01

PDF · 533 SEK

Standard · ASTM ASTM A513

Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing

1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. 1.2 This specification covers mechanical tubing made from hot- or cold-rolled st...

Språk

Publicerad

2007-05-09

Upphävd

2008-10-01

PDF · 611 SEK

Standard · ASTM ASTM A531/A531M

Standard Practice for Ultrasonic Examination of Turbine-Generator Steel Retaining Rings

1.1 This practice covers the procedures to be followed when performing ultrasonic shear and longitudinal wave tests on turbine-generator retaining rings with an inside diameter to wall thickness ra...

Språk

Publicerad

2006-03-01

Upphävd

2012-03-01

PDF · 533 SEK

Standard · ASTM ASTM A582/A582M

Standard Specification for Free-Machining Stainless Steel Bars

1.1 This specification covers hot-finished or cold-finished bars, except bars for forging (Note 1). It includes rounds, squares, and hexagons in the more commonly used types of stainless free-machi...

Språk

Publicerad

2005-03-01

Upphävd

2012-03-01

PDF · 468 SEK

Standard · ASTM ASTM A612/A612M

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

1.1 This specification covers killed carbon-manganese-silicon steel plates intended for welded pressure vessels in service at moderate and lower temperatures. 1.2 The maximum thickness of plate...

Språk

Publicerad

2008-04-09

Upphävd

2012-05-01

PDF · 468 SEK

Förfina din sökning genom att visa:

...som handlar om: