21299 träffar på

Standard · ASTM ASTM F1897

Standard Specification for Leg Protection for Chain Saw Users

1.1 This specification specifies minimum requirements for the design, performance, testing, and certification of protective garments and protective devices designed to provide cut resistance protec...

Språk

Publicerad

2004-10-01

Upphävd

2008-06-15

PDF · 533 SEK

Standard · ASTM ASTM F2157

Standard Specification for Synthetic Surfaced Running Tracks

1.1 This specification establishes the minimum performance requirements and classification when tested in accordance with the procedures outlined within this specification. All documents referencin...

Språk

Publicerad

2002-06-10

Upphävd

2008-06-15

PDF · 611 SEK

Standard · ASTM ASTM D4612

Standard Practice for Calculating Thermal Diffusivity of Rocks

1.1 This practice involves calculation of the thermal diffusivity from measured values of the mass density, thermal conductivity, and specific heat at constant pressure. It is applicable for any ma...

Språk

Publicerad

2003-06-10

Upphävd

2008-07-01

PDF · 468 SEK

Standard · ASTM ASTM D4623

Standard Test Method for Determination of In Situ Stress in Rock Mass by Overcoring Method-USBM Borehole Deformation Gage

1.1 This test method covers the determination of the ambient local stresses in a rock mass and the equipment required to perform in situ stress tests using a three-component borehole deformation ga...

Språk

Publicerad

2005-11-01

Upphävd

2008-07-01

PDF · 611 SEK

Standard · ASTM ASTM D4644

Standard Test Method for Slake Durability of Shales and Similar Weak Rocks

1.1 This test method covers the determination of the slake durability index of a shale or other similar rock after two drying and wetting cycles with abrasion.1.2 All observed and calculated values...

Språk

Publicerad

2004-02-01

Upphävd

2008-07-01

PDF · 468 SEK

Standard · ASTM ASTM E4

Standard Practices for Force Verification of Testing Machines

1.1 These practices cover procedures for the force verification, by means of standard calibration devices, of tension or compression, or both, static or quasi-static testing machines (which may, or...

Språk

Publicerad

2007-01-01

Upphävd

2008-12-01

PDF · 533 SEK

Standard · ASTM ASTM D6246

Standard Practice for Evaluating the Performance of Diffusive Samplers

1.1 This practice covers the evaluation of the performance of diffusive samplers of gases and vapors for use over sampling periods from 4 to 12 h and for wind speeds less than 0.5 m/s. Such samplin...

Språk

Publicerad

2002-10-10

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM D6966

Standard Practice for Collection of Settled Dust Samples Using Wipe Sampling Methods for Subsequent Determination of Metals

1.1 This practice covers the collection of settled dust on surfaces using the wipe sampling method. These samples are collected in a manner that will permit subsequent extraction and determination ...

Språk

Publicerad

2003-10-01

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM E223

Standard Test Methods for Analysis of Sulfuric Acid

1.1 These test methods cover the analysis of sulfuric acid.1.2 The analytical procedures appear in the following order:SectionsTotal Acidity8 to 16Baum Gravity</T

Språk

Publicerad

2002-10-10

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM E1014

Standard Guide for Measurement of Outdoor A-Weighted Sound Levels

1.1 This guide covers the measurement of A-weighted sound levels outdoors at specified locations or along particular site boundaries, using a general purpose sound-level meter.1.2 Three distinct ty...

Språk

Publicerad

2000-01-01

Upphävd

2008-03-01

PDF · 533 SEK

Standard · ASTM ASTM E1054

Standard Test Methods for Evaluation of Inactivators of Antimicrobial Agents

1.1 These methods are used to determine the effectiveness of procedures and agents for inactivating (neutralizing, quenching) the microbiocidal properties of antimicrobial agents and to ensure that...

Språk

Publicerad

2002-05-10

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM F484

Standard Test Method for Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds

1.1 This test method covers determination of the crazing effect that a liquid or semi-liquid test compound will have on transparent acrylic plastic material that is under bending stress.1.2 Three t...

Språk

Publicerad

2002-05-10

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM F502

Standard Test Method for Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces

1.1 This test method covers determination of the effects of cleaning solutions and liquid cleaner concentrates on painted aircraft surfaces (Note 1). Streaking, discoloration, and blistering may be...

Språk

Publicerad

2002-08-10

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM B888

Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts

1.1 This specification establishes the requirements for copper alloy strip for use in the manufacture of electrical connectors or spring contacts produced from one of the following Copper Alloy UNS...

Språk

Publicerad

2006-03-15

Upphävd

2008-04-01

PDF · 611 SEK

Standard · ASTM ASTM C1631

Standard Specification for Cellular Polypropylene Thermal Insulation

1.1 This specification covers the types, physical properties, and dimensions of cellular polypropylene intended for use as thermal insulation for temperatures from - 150 to + 240°F (-101 t...

Språk

Publicerad

2005-11-01

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM F2602

Standard Test Method for Determining the Molar Mass of Chitosan and Chitosan Salts by Size Exclusion Chromatography with Multi-angle Light Scatteri...

1.1 This test method covers the determination of the molar mass of chitosan and chitosan salts intended for use in biomedical and pharmaceutical applications as well as in tissue engineered medical...

Språk

Publicerad

2008-08-06

PDF · 533 SEK

Standard · ASTM ASTM F2605

Standard Test Method for Determining the Molar Mass of Sodium Alginate by Size Exclusion Chromatography with Multi-angle Light Scattering Detection...

1.1 This test method covers the determination of the molar mass of sodium alginate intended for use in biomedical and pharmaceutical applications as well as in tissue engineered medical products (T...

Språk

Publicerad

2008-08-06

PDF · 533 SEK

Standard · ASTM ASTM B584

Standard Specification for Copper Alloy Sand Castings for General Applications

1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in . This is a composi...

Språk

Publicerad

2007-01-11

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM E1277

Standard Test Method for Chemical Analysis of Zinc-5% Aluminum-Mischmetal Alloys by ICP Emission Spectrometry

1.1 This test method covers the chemical analysis of zinc alloys having chemical compositions within the following limits:ElementConcentration Range, %Aluminum3.0-8.0</

Språk

Publicerad

2002-10-10

Upphävd

2008-03-01

PDF · 533 SEK

Standard · ASTM ASTM F1115

Standard Test Method for Determining the Carbon Dioxide Loss of Beverage Containers

1.1 The objective of this test method is to determine the carbon dioxide (CO2) loss from plastic beverage containers after a specified period of storage time. 1.2 Factors contributing to this press...

Språk

Publicerad

2008-02-01

PDF · 611 SEK

Standard · ASTM ASTM B49

Standard Specification for Copper Rod Drawing Stock for Electrical Purposes

1.1 This specification covers the requirements for rod drawing stock in diameters from 1/4 to 13/8 in. (6.4 to 35 mm) produced from electrolytic tough-pitch or oxygen-free coppers and are suitable ...

Språk

Publicerad

2004-05-01

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM B61

Standard Specification for Steam or Valve Bronze Castings

1.1 This specification establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C92200) used for component castings of valves, flanges, and fittings.1.2 The...

Språk

Publicerad

2002-12-10

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM B124/B124M

Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes

1.1 This specification establishes the requirements for copper and copper alloy rod, bar, and shapes intended for hot forging. The following coppers and copper alloys are involved: Copper UNS Nos.C...

Språk

Publicerad

2006-02-01

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM B134/B134M

Standard Specification for Brass Wire

1.1 This specification establishes requirements for round, hexagonal, octagonal, rectangular and square brass wire of UNS Alloys C21000, C22000, C22600, C23000, C23400, C24000, C26000, C27000, and ...

Språk

Publicerad

2005-10-01

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM B301/B301M

Standard Specification for Free-Cutting Copper Rod, Bar, Wire and Shapes

1.1 This specification establishes the requirements for free-cutting copper rod, bar, wire, and shapes of UNS Alloy Nos. C14500, C14510, C14520, C14700, and C18700, suitable for high-speed screw ma...

Språk

Publicerad

2004-05-01

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM C71

Standard Terminology Relating to Refractories

1.1 This terminology covers terms particularly related to refractories and encompasses raw materials, manufacture, finished products, applications, and testing procedures. 1.2 When any of the defi...

Språk

Publicerad

2008-02-06

Upphävd

2008-04-01

PDF · 533 SEK

Standard · ASTM ASTM B395/B395M

Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes

1.1 This specification establishes the requirements for condenser, evaporator, and heat exchanger U-bends that are manufactured from seamless copper and copper alloy tube. 1.2 UnitsThe values state...

Språk

Publicerad

2002-04-10

Upphävd

2008-04-01

PDF · 611 SEK

Standard · ASTM ASTM E298

Standard Test Methods for Assay of Organic Peroxides

1.1 These test methods cover the assay of organic peroxides. Two procedures are given, depending upon the ease of reduction: 1.1.1 Sodium Iodide, Room Temperature Test Method, for organic perox...

Språk

Publicerad

2001-10-10

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM E299

Standard Test Method for Trace Amounts of Peroxides In Organic Solvents

1.1 This test method covers organic solvents containing active oxygen in the range from 5 to 80 ppm or higher. By using a special reaction-absorption cell, the test method can be extended to cover ...

Språk

Publicerad

2002-12-10

Upphävd

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM E449

Standard Test Methods for Analysis of Calcium Chloride

1.1 These test methods cover the analysis of calcium chloride and solutions.1.2 Procedures are given for the determination of calcium chloride, magnesium chloride, potassium chloride, sodium chlori...

Språk

Publicerad

1996-12-10

Upphävd

2008-04-01

PDF · 533 SEK

Förfina din sökning genom att visa:

...som handlar om: