21305 träffar på

Standard · ASTM ASTM C655M Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) 1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construct... Språk Publicerad 2011-03-18 Upphävd 2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM C726 Standard Specification for Mineral Wool Roof Insulation Board 1.1 This specification covers the composition and physical properties of mineral wool insulation board used above structural roof decks in building construction. The mineral wool roof insulation a... Språk Publicerad 2011-10-14 Upphävd 2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM C1044 Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode 1.1 This practice covers the determination of the steady-state heat flow through the meter section of a specimen when a guarded-hot-plate apparatus or thin-heater apparatus is used in the single-si... Språk Publicerad 2007-10-10 Upphävd 2012-03-01

PDF · 533 SEK

Standard · ASTM ASTM D36/D36M Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) 1.1 This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C [86 to 315°F] using the ring-and-ball apparatus immersed Språk Publicerad 2009-12-15 Upphävd 2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM D167 Standard Test Method for Apparent and True Specific Gravity and Porosity of Lump Coke 1.1 This test method covers the determination of apparent specific gravity (Sections to ) and true specific gravity (Sections 2 to 9) of lump coke larger than 25-mm (1-in.) size and calculating po... Språk Publicerad 2004-04-01 Upphävd 2012-02-01

PDF · 468 SEK

Standard · ASTM ASTM D2013/D2013M Standard Practice for Preparing Coal Samples for Analysis 1.1 This practice covers the reduction and division of gross or divided samples, and the preparation of composite samples, up to and including the individual portions for laboratory analysis. 1... Språk Publicerad 2011-09-16 Upphävd 2012-04-01

PDF · 611 SEK

Standard · ASTM ASTM D3180 Standard Practice for Calculating Coal and Coke Analyses from As-Determined to Different Bases 1.1 This practice gives formulas to enable analytical data to be expressed on various different bases in common use. Such bases are: as received, dry, equilibrium moisture, dry ash free, and others... Språk Publicerad 2007-09-05 Upphävd 2012-04-01

PDF · 468 SEK

Standard · ASTM ASTM D3302/D3302M Standard Test Method for Total Moisture in Coal 1.1 This test method covers the measurement of the total moisture in coal as it exists at the site, at the time, and under the conditions it is sampled. It is applicable to coals as mined, process... Språk Publicerad 2010-01-01 Upphävd 2012-04-01

PDF · 533 SEK

Standard · ASTM ASTM D6354 Standard Guide for Sampling Plan and Core Sampling of Carbon Cathode Blocks Used in Aluminum Production 1.1 This sampling guide was developed for carbon cathode blocks used in the production of aluminum, and details procedures for taking test samples from single cathode blocks. It covers equipment an... Språk Publicerad 2008-10-15 Upphävd 2012-04-15

PDF · 468 SEK

Standard · ASTM ASTM D6374 Standard Test Method for Volatile Matter in Green Petroleum Coke Quartz Crucible Procedure 1.1 This test method covers the determination of the volatile matter produced by pyrolysis or evolved when petroleum coke is subjected to the specific conditions of the test method. 1.2 The interla... Språk Publicerad 2004-11-01 Upphävd 2012-04-15

PDF · 468 SEK

Standard · ASTM ASTM D6560 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products 1.1 This test method covers a procedure for the determination of the heptane insoluble asphaltene content of gas oil, diesel fuel, residual fuel oils, lubricating oil, bitumen, and crude petroleum ... Språk Publicerad 2005-11-01 Upphävd 2012-04-15

PDF · 533 SEK

Standard · ASTM ASTM D7736 Standard Test Method for Determination of Acids and Glycol Esters in Ethylene Glycol 1.1 This test method covers the determination of free acids and glycol esters in ethylene glycol by titration. 1.2 This test method is for used on ethylene glycol used for the manufacture of engine... Språk Publicerad 2012-02-24 Upphävd 2012-04-01

PDF · 468 SEK

Standard · ASTM ASTM E202 Standard Test Methods for Analysis of Ethylene Glycols and Propylene Glycols 1.1 These test methods cover the chemical and physical analysis of the commonly available grades of ethylene glycol, diethylene glycol, triethylene glycol, propylene glycol, and dipropylene glycol... Språk Publicerad 2010-10-15 Upphävd 2012-04-01

PDF · 611 SEK

Standard · ASTM ASTM E253 Standard Terminology Relating to Sensory Evaluation of Materials and Products - Språk Publicerad 2011-08-25 Upphävd 2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM E411 Standard Test Method for Trace Quantities of Carbonyl Compounds with 2,4-Dinitrophenylhydrazine 1.1 This test method covers the determination of total carbonyl in the range from 0.5 to 50 g calculated as CO.1.2 This test method is intended to be general and does not include steps for sample p... Språk Publicerad 2005-03-01 Upphävd 2012-04-01

PDF · 468 SEK

Standard · ASTM ASTM E557 Standard Guide for The Installation of Operable Partitions 1.1 This guide describes options of intructions recommended to be considered in preparation for, and application and installation of, operable partitions and, to some extent, in the design of the b... Språk Publicerad 2000-09-10 Upphävd 2012-04-01

PDF · 533 SEK

Standard · ASTM ASTM E557 Standard Guide for The Installation of Operable Partitions 1.1 This guide describes options of intructions recommended to be considered in preparation for, and application and installation of, operable partitions and, to some extent, in the design of the b... Språk Publicerad 2007-02-07 Upphävd 2012-04-01

PDF · 533 SEK

Standard · ASTM ASTM E1064 Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration 1.1 This test method covers the determination of water from 0 to 2.0 % mass in most liquid organic chemicals, with Karl Fischer reagent, using an automated coulometric titration procedure. Use of t... Språk Publicerad 2008-08-06 Upphävd 2012-04-01

PDF · 468 SEK

Standard · ASTM ASTM E2253 Standard Method for Enthalpy Measurement Validation of Differential Scanning Calorimeters 1.1 This test method provides procedures for validating enthalpic measurements of differential scanning calorimeters (DSC) and analytical methods based upon the measurement of enthalpy or heat by D... Språk Publicerad 2008-09-01 Upphävd 2011-12-01

PDF · 533 SEK

Standard · ASTM ASTM F1344 Standard Specification for Rubber Floor Tile 1.1 This specification covers requirements for the compound and physical characteristics of rubber floor tile. 1.2 The values stated in inch-pound units are to be regarded as standard. The values g... Språk Publicerad 2004-03-01 Upphävd 2010-05-01

PDF · 468 SEK

Standard · ASTM ASTM F1344 Standard Specification for Rubber Floor Tile 1.1 This specification covers requirements for the compound and physical characteristics of rubber floor tile. 1.2 The values stated in inch-pound units are to be regarded as standard. The values g... Språk Publicerad 2010-08-20 Upphävd 2012-05-15

PDF · 468 SEK

Standard · ASTM ASTM F1717 Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model 1.1 These test methods cover the materials and methods for the static and fatigue testing of spinal implant assemblies in a vertebrectomy model. The test materials for most combinations of spinal i... Språk Publicerad 2011-09-16 Upphävd 2012-05-15

PDF · 611 SEK

Standard · ASTM ASTM F1859 Standard Specification for Rubber Sheet Floor Covering Without Backing 1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering without backing. 1.2 The values stated in inch-pound units are to be reg... Språk Publicerad 2010-06-18 Upphävd 2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM F1860 Standard Specification for Rubber Sheet Floor Covering With Backing 1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain inter... Språk Publicerad 2010-06-18 Upphävd 2012-05-01

PDF · 468 SEK

Standard · ASTM ASTM F2169 Standard Specification for Resilient Stair Treads 1.1 This specification covers resilient treads made of rubber and vinyl for interior use.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parenthese... Språk Publicerad 2008-03-01 Upphävd 2012-05-15

PDF · 468 SEK

Standard · ASTM ASTM A416/A416M Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed Concrete 1.1 This specification covers two types and two grades of seven-wire, uncoated steel strand for use in pretensioned and post-tensioned prestressed concrete construction. The two types of stran... Språk Publicerad 2010-08-20 Upphävd 2012-04-01

PDF · 533 SEK

Standard · ASTM ASTM A609/A609M Standard Practice for Castings, Carbon, Low-Alloy, and Martensitic Stainless Steel, Ultrasonic Examination Thereof 1.1 This practice covers the standards and procedures for the pulse-echo ultrasonic examination of heat-treated carbon, low-alloy, and martensitic stainless steel castings by the longitudinal-beam ... Språk Publicerad 2008-01-09 Upphävd 2012-05-01

PDF · 533 SEK

Standard · ASTM ASTM B26/B26M Standard Specification for Aluminum-Alloy Sand Castings 1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1. 1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications. 1... Språk Publicerad 2012-02-24 Upphävd 2012-05-01

PDF · 611 SEK

Standard · ASTM ASTM B108/B108M Standard Specification for Aluminum-Alloy Permanent Mold Castings 1.1 This specification covers aluminum-alloy permanent mold castings designated as shown in Table 1. 1.2 This specification is not intended for aluminum-alloy permanent mold castings used in aeros... Språk Publicerad 2012-02-24 Upphävd 2012-05-01

PDF · 611 SEK

Standard · ASTM ASTM B917/B917M Standard Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes 1.1 This practice covers, when specified by material specification or purchase order, the heat treatment of aluminum alloy castings from all casting processes. 1.1.1 The heat treatment of aluminum ... Språk Publicerad 2011-09-16 Upphävd 2012-05-01

PDF · 611 SEK

• < Föregående
• 424
• 425
• 426
• 427
• 428
• 429
• 430
• 431
• 432
• 433
• Nästa >