1.1 This practice covers sampling and analysis procedures for the investigation of specified populations of wood and wood-based structural products referred to in this standard as products. Appropr...
2011-04-15
1.1 These practices for the calibration of mechanical soil compactors are for use in checking and adjusting mechanical devices used in laboratory compacting of soil and soil-aggregate in accordance...
2010-09-17
1.1 This specification covers aluminum-alloy 6201-T81 (hard: solution heat-treated, cold worked, and artificially aged) round wire for electrical purposes.This specification covers alumi...
2007-12-05
1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I physically removes the matrix by digestion or ignition by one of seven proced...
2011-12-16
1.1 This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The reference radiogr...
2011-09-16
1.1 This standard provides a general method of selecting effective constituents for detection monitoring programs at RCRA Waste Disposal Facilities. The process described in this standard presents ...
2004-05-01
1.1 This specification defines the chemical and physical requirements for boron carbide powder intended for a variety of nuclear applications. Because each application has a different need for imp...
2009-07-01
1.1 This test method covers procedures for detecting pores, cracks, or other voids that may be present in otherwise impermeable whiteware ceramics, or as porosity in underfired ware. No
2007-09-05
1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1).This specification deals with figure-9 deep-section g...
2007-05-09
1.1 These test methods cover testing of single filament steel wires that are used to reinforce hose products. By agreement, these test methods may be applied to similar filaments used for reinforc...
2011-05-20
1.1 This specification covers the general requirements for materials used in rubber seals of flat-plate solar collectors, except vertically mounted passive collectors. Particular applications may n...
2005-12-01
1.1 This test method covers the determination of the force necessary to separate the dip tube from the body of a mechanical pump dispenser (spray or flow types). 1.2 This standard does not purport to
2005-10-01
1.1 This test method covers the determination of alpha-particle-emitting isotopes of uranium in water by means of chemical separations and alpha pulse-height analysis (also known as alpha-particle ...
2009-02-01
1.1 This test method furnishes a way of measuring, in the laboratory, the performance of a foaming chemical to be used in producing foam (air cells) for making cellular concrete. 1.2 This test met...
2004-11-01
1.1 This test method covers the Calculated Cetane Index formula, which represents a means for directly estimating the ASTM cetane number of distillate fuels from API gravity and mid-boiling point. ...
2007-02-07
1.1 This practice describes procedures for testing geonet products for chemical resistance with liquid wastes, prepared chemical solutions, or leachates, or both, derived from soli
2005-06-01
1.1 This specification covers the requirements for electrodeposited tin-nickel alloy coatings from aqueous solutions intended for the corrosion protection of fabricated articles of iron, steel, zi...
2004-04-01
1.1 This specification covers round, aluminum-clad steel core wire with two designations of tensile strengths, AW2 (Normal Strength) and AW3 (High Strength). 1.2 The values stated in either SI unit...
2011-03-18
1.1 A traffic paint film freshly applied to a roadway, air strip, or parking lot may be exposed to rain of varying intensities shortly after application. This practice was designed to det...
2009-06-01
1.1 These test methods cover the determination of the fineness of frit in wet- or dry-milled porcelain enamels and other ceramic coatings for metals by means of the No. 200 (75-μm) or No...
2010-06-18
1.1 This specification covers and is intended to reduce strangulation and vehicular dragging hazards associated with drawstrings on children's upper outerwear. 1.2 The type of clothing covered by t...
2009-10-01
1.1 This specification covers high calcium, dolomitic and magnesian-hydrated lime for use in asphalt cement or bituminous pavement. This specification covers high calcium, dolomitic and ...
1.1 This test method covers determining the density and taxonomic classification of phytoplankton. It is applicable both to relatively sparse or dense phytoplankton concentrations,
1.1 This specification covers the procedure for longitudinal Charpy V-notch testing of structural steel and contains two frequencies of testing. The impact properties of steel can vary within the ...
1.1 This guide covers the evaluation of chitosan salts suitable for use in biomedical or pharmaceutical applications, or both, including, but not limited to, tissue-engineered medical products (TEM...
1.1 This guide covers procedures for irradiation of dried spices, herbs, and vegetable seasonings for microbiological control. Generally, these items have moisture content of 4.5 to 12 % and are ...
2004-01-01
1.1 These test methods cover bend testing for ductility of materials. Included in the procedures are four conditions of constraint on the bent portion of the specimen; a guided-bend test using a ma...
2009-04-01
1.1 This test method describes the steps necessary for the preparation and determination of impurity metals in uranium metal and uranium compounds by DC arc emission spectroscopy. 1.2 The method is...
1.1 These test methods cover plant manufacturing procedures for measuring the thickness of flat sandwich cores. Permissible core material forms include those with continuous bonding surfaces (such ...
2011-06-17
1.1 This specification covers minimum performances and specification criteria for an air barrier (AB) material or system for framed walls of low-rise buildings. The intended users are purchasers o...