1.1 These test methods are intended for use in determining the total, neutral, and combined acid sulfate in mineral-tanned leather. 1.2 The values stated in SI units are to be regarded as standard....
2006-10-01
1.1 These test methods cover the determination of the operating capacity of particulate cation-exchange materials when used for the removal of calcium, magnesium, and sodium ions from water. It is...
2008-02-06
1.1 This practice covers procedures commonly used in the paint industry to formulate paints and coating materials. It describes procedures for calculating formulation valu...
2010-02-01
1.1 This test method covers the procedure to be used to determine the force-draw and let-down curves for archery bows. 1.2 The values stated in inch-pound units are to be regarded as the standard. ...
2007-12-05
1.1 This guide establishes essential and desirable data elements for fiber-reinforced composite materials for two purposes: to establish the material identification component of data-reporting requ...
2005-10-01
1.1 This practice provides guidelines for acoustic emission (AE) examinations of seamless pressure vessels (tubes) of the type used for distribution or storage of industrial gases. 1.2 This practic...
2009-02-01
1.1 This specification covers requirements for epoxy thermosetting molding compounds. It provides for their identification, quality control, and purchase in such a manner that the This s...
2004-10-01
1.1 This test method covers a procedure to determine the insulation resistance of a photovoltaic (PV) array (or its component strings), that is, the electrical resistance between the array's intern...
2010-09-17
1.1 This test method covers the determination of the shock-attenuation characteristics of protective headgear for football. 1.2 The values stated in SI units are to be regarded as standard. No oth...
2010-10-15
1.1 This test method covers the determination of the resistance of organic coatings to abrasion produced by the Taber Abraser on coatings applied to a plane, rigid surface, such as a meta...
1.1 This specification covers uncoated, indented, low-relaxation steel wire for use as prestressing tendons in concrete railroad ties. 1.2 The values stated in either inch-pound units or SI units ...
2011-05-20
1.1 A binary chemical compatibility chart also called inter-reactivity chart, documents the hazards associated with the mixing of pairs of materials. This guide provides an aid for
2006-04-01
1.1 This practice covers three types of laboratory weathering exposure procedures for evaluating the effect of actinic radiation, heat, and moisture on sealants. 1.2 The exposure sources used in th...
1.1 This practice describes continuous sample conditioning by hydrogen ion exchange and measurement by electrolytic conductivity. It is commonly known as cation conductivity measurement in the pow...
2011-09-16
1.1 This test method provides a means of determining the book bulk and bulking number of printing paper under a specified pressure.1.2 For thickness of single sheets or small packs of sheets, see T...
2007-09-05
2010-08-01
1.1 This guide provides guidelines for widths and lengths of pressure-sensitive tape, including tolerances and labeling in the inch-pound and SI systems. It is not intended for tapes used for medi...
1.1 This test method covers the removal of pentanes and lighter hydrocarbons from gasolines, naphthas, and similar petroleum distillates to prepare samples suitable for the determi
2008-03-12
1.1 This test method covers a general procedure for the determination of elemental content in polyolefins by wavelength-dispersive X-ray fluorescence (WDXRF) spectrometry, in mass fraction ranges t...
1.1 This specification2 covers minimum-wall-thickness, seamless medium-carbon steel, boiler t This specification covers seamless medium-carbon steel boiler and superheater tubes. The spe...
2002-09-10
1.1 This specification covers ethyl acrylate (99 % grade) for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for pur...
2009-06-01
1.1 This test method covers the determination of the hydroperoxide content expressed as hydroperoxide number of aviation turbine, gasoline and diesel fuels. <div class="S
1.1 This test method covers the determination of oil and grease in produced and waste water samples over the concentration range outlined in Table 1 that can be extracted with an infrared-amenable ...
2011-12-16
1.1 This test method covers accelerated testing for compressive creep properties using the Stepped Isothermal Method (SIM). <p class="subsec1"
2008-05-14
Dissipation factor, permittivity and dc volume resistivity are properties of communication cable fillers and filler components that are controlled in order that the cable's electrical performance f...
1999-04-10
1.1 This test method covers establishing the moisture-penetration resistance relationships of fine-grained soils as determined by the soil penetrometer. 1.2 The values stated in inch-pound units ar...
2011-04-15
1.1 This practice covers a procedure for determining the conformance of geosynthetic properties to standard specifications. 1.2 This standard does not purport to address all of the safety concerns, if
2011-10-14
1.1 This specification covers the establishment of the minimum requirements for the design, testing, and quality assurance of fixed-pitch or ground adjustable propellers for light sport aircraft....
1.1 These test methods cover the determination of specific resistance (resistivity) of liquid paints, solvents, and other fluids in the range of 0.6 to 2640 MΩ-cm.
2008-10-08
1.1 This guide lists the responsibilities of the end user and the infrared thermographer when examining electrical and mechanical systems. 1.2 This guide outlines the specific content required to ...
1999-12-10
1.1 This specification covers nickel-chromium-molybdenum-columbium alloys (UNS N06625 and UNS N06852) and nickel-chromium-molybdenum-silicon alloy (UNS N06219)* in the form of cold-worked se...
2007-02-07