1.1 This test method covers the determination of the precipitation number of steam cylinder stocks and black oils, and can be used for other lubricating oils. <div class=
2007-09-05
1.1 This practice covers guidelines for using accelerometers in test vehicles to evaluate dynamic accelerations resulting from various maneuvers such as braking, accelerating, or cornering. 1.2 Thi...
2002-10-10
1.1 This test method is used to develop test data from which the susceptibility of polyolefin geomembrane sheet material to stress cracking under a constant tensile load condition
1.1 This test method covers the detection of gross leaks in packaging. Method sensitivity is down to 250 μm (0.010 in.) with an 81 % probability (see Section 11). This test method may be...
2012-03-23
1.1 This test method covers the determination of total sulfur in liquefied petroleum gases containing more than 1 μg/g. Specimens should not contain more than 100 μg/g
2011-05-20
1.1 This test method covers the determination of the ash content of fats and oils used in the softening and stuffing of leather and in the manufacture of fatliquors and other softening and stuffing...
2006-04-01
1.1 These test methods (and references) cover the procedures for evaluating the physical properties of flat conveyor belting. Performance criteria for belting will not be detailed here, but can be ...
1.1 This specification covers lime and limestone products suitable for the following chemical and industrial uses: This specification covers lime and limestone products that are suitable for chemic...
2006-11-15
1.1 This test method covers tents for use in the sports of backpacking and mountaineering. It establishes requirements for the testing and marking of tents. 1.2 This test method may contain test me...
2001-11-10
1.1 This terminology standard covers terms that relate to the durability testing of Nonmetallic Materials using natural and artificial weathering exposure techniques. 1.2 It is the intent of this t...
2009-06-15
1.1 This practice covers a procedure for preparing test specimens from magnesia-carbon and impregnated burned basic brick. This practice generally concerns preparation of test specimens from brick...
2005-12-01
1.1 This guide prescribes a method for preparing cemented carbides for metallographic examination. 1.2&
2008-11-01
1.1 This test method is applicable to determine the pH of water samples with a conductivity of 2 to 100 μS/cm over the pH range of 3 to 11. pH measurements of water of low conductivity ...
2011-09-16
1.1 This practice describes procedures for providing exposure of thermal control materials to a simulated space environment comprising the major features of vacuum, electromagnetic radiation, charg...
2004-09-01
1.1 This test method provides an accelerated means of determining the relative sealing abilities of pipeline patching materials that are used to seal holidays in pipeline coatings on steel pipe. Th...
1998-07-10
2007-03-21
1.1 This test method covers the determination of the forms of chlorine in refuse-derived fuel-three (RDF): total chlorine, water-soluble chloride, and water-insoluble chlorine. 1.2 This test method...
1987-08-28
1.1 These test methods cover the determination of the hydrogen content of petroleum products ranging from atmospheric distillates to vacuum residua using a continuous wave, low-resolution nuclear m...
2006-05-01
1.1 This specification covers standard practice for assembly, placement and filling of double-twisted wire mesh gabions and revet mattresses used for various erosion control, soil retention or free...
2010-08-20
1.1 This test method describes the analysis of aluminum and its alloys by atomic emission spectrometry. The aluminum specimen to be analyzed may be in the form of a chill cast disk, casting, foil, ...
1.1 This specification covers welded UNS N06110 pipe in the annealed condition (temper) for general corrosion applications. 1.2 This specification covers pipe sizes in schedules shown in Table 1...
2006-06-01
1.1 This guide describes an approach for demonstrating the quality of analytical chemical measurement results from the application of a measurement system (that is, method or sequence of methods) t...
1.1 This test method covers the determination of the amount of bromine-reactive material in petroleum hydrocarbons and is thus a measure of trace amounts of unsaturates in these materials. It is a...
2009-10-01
1.1 This test method describes the determination of the ash content of pulp, paper, and paper products by ignition at two different temperatures:1.1.1 Method A—Ash content upon ignition a...
1997-12-10
2009-09-01
1.1 This practice gives suggested procedures for the characterization of atmospheric test sites. Continuous characterization can provide corrosion data, environmental data, or both which will signa...
2010-09-01
1.1 This terminology is intended for use by barbed tape specifiers and end-users to give a general understanding of the types, sizes, and configuration of barbed tape.
2008-06-01
1.1 This practice covers the procedure for calibration of instruments to be used for estimating the ferrite content of the microstructure of cast stainless steels by magnetic response or measuremen...
2010-05-17
1.1 This test method covers the measurement of the force and elongation required to dispense pressure-sensitive film tape on a 1-in. core intended for office and stationery applications from a desk...
1998-08-10
1.1 This specification covers the procedure and acceptance standards for straight-beam, pulse-echo, ultrasonic examination of rolled fully killed carbon and alloy steel plates, ½ in. [1...
2007-05-09
1.1 This specification covers ferrous earthy pigment included under the general term “ochre.” The pigment may be purchased in the dry form. This specification covers ferrous ...
2005-09-01
1.1 This practice applies to the instrumental color measurement of fluorescent specimens excited by near ultraviolet and visible radiation that results in fluorescent emission within the visible ...