1.1 This specification covers coextruded composite drain, waste, and vent pipe (DWV). The pipe is produced in Schedule 40 IPS sizes by a coextrusion die system, in which the concentric layers are...
2012-05-16
1.1 This test method describes procedures for the assignment of the glass transition temperature of materials on heating using thermomechanical measurements under prescribed experimental conditions...
2011-09-16
1.1 This test method covers the determination of individual hydrocarbon components of spark-ignition engine fuels and their mixtures containing oxygenate blends (MTBE, ETBE, ethanol, and so forth) ...
2006-11-01
1.1 This test method describes the calculation of true vapor pressures of petroleum distillate fuels for which distillation data may be obtained in accordance with Test Method <a href="http://my...
2005-11-01
1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar. The classifications of concrete and mort...
2011-05-20
1.1 This practice covers the procedure, any necessary related apparatus, and the sampling technique to be used in determining the performance characteristics of oil/water separators subjected to c...
2003-06-10
1.1 This test method covers a practical test for the solubility of commercial chemicals used in rubber products. 1.2 It is not a true measure of solubility, since equilibrium is not approached fr...
2005-10-01
1.1 This test method describes the assessment of constant-temperature stability of chemical materials that undergo exothermic reactions. The techniques and apparatus described may be used on solids...
2009-11-01
1.1 This practice covers a uniform procedure for radioscopic examination of castings. 1.2 This practice applies only to radioscopic examination in which an image is finally presented on a display s...
2009-07-01
1.1 This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films up to 3 mm (0.1 in.) in...
2006-06-22
1.1 This test method describes a procedure for measuring the pore size characteristics of membrane filters in the range of approximately 0.05 to 300 [mu]m. 1.2 This test method uses the automated ...
1999-10-10
2008-09-24
1.1 This classification system covers the classification of rubber-grade carbon blacks by the use of a four-character nomenclature system. The first character gives some indication of the influenc...
2010-01-01
1.1 This practice covers the procedure for sorting materials using the thermoelectric method, which is based on the Seebeck effect. The procedure relates to the use of direct- and comparator-type t...
2005-07-01
1.1 This guide contains a comprehensive discussion of potential requirements for a sample chain-of-custody program and describes the procedures involved in sample chain-of-custody. The purpose of...
1999-12-10
1.1 This guide defines simple economical procedures for testing or comparing the performance of acoustic emission sensors. These procedures allow the user to check for degradation of a sensor or to...
2010-09-17
1.1 This specification covers raw tung oil derived from Aleurites fordii Hemsley.
1998-05-10
2007-03-16
1.1 This practice describes the calculation of the heat of vaporization of a liquid or the heat of sublimation of a solid from measured vapor pressure data. It is applicable to pure liquids, azeot...
2005-03-01
1.1 This test method describes standardized procedures for the sensory evaluation of heat in oleoresin capsicums ranging from 100 000 to 1 000 000 Scoville heat units (S.H.U.). 1.2 This test metho...
2004-10-01
1.1 This guide covers information to assist in the selection of a method for measuring the frictional properties of materials. Requirements for minimum data and a format for presenting these data...
2010-11-19
1.1 This test method covers how to measure the apparent viscosity of used and soot-containing engine oils at low temperatures. 1.2 A shear rate of approximately 0.2 s-1 is produced at shear stresse...
2005-04-01
1.1 This test method includes several procedures that can be used for the measurement of overall package and seal barrier performance of a variety of package types and package forms, as well as sea...
2005-01-01
1.1 This procedure describes a method of measuring the dynamic stiffness (DS) and cylindrical coefficient of restitution (CCOR) of baseballs and softballs providing similar impact forces and ball d...
1.1 This specification covers the requirements for wrought 18chromium-14nickel-2.5molybdenum stainless steel tubing used for the manufacture of surgical implants. Material shall conform to the appl...
2009-02-01
1.1 This test method covers the ability of a grease to adhere to a metal surface when subjected to a water spray under prescribed laboratory conditions. 1.2 The values stated in SI units are to be...
1.1 This practice covers the calibration and use of torque meters of the type normally used in packaging applications. 1.2 This standard does not purport to address all of the safety concerns, if any
2007-12-05
1.1 This specification covers non-asbestos fiber-cement conduit for use in electric-power systems and communication systems. The service is for both underground and exposed conditions. 1.2 The valu...
2005-04-05
1.1 This test method covers the determination of bulk density of a representative 2-kg sample of calcined petroleum coke, after vibration to increase compaction. 1.2 The procedure is limited to par...
1.1 This practice covers procedures for testing the joints of installed precast concrete pipe sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joi...
2003-11-01
1.1 This standard defines the specialized terms used in standards developed by Committee F23 on Protective Clothing. 1.2 Definitions of Terms, which were drafted for use only in a single standard, ...
2003-07-10
1.1 This practice covers a procedure for determining the amount of coating applied to a substrate, (for example, film, paper, nonwoven). The amount of coating is expressed as a wei
2007-09-05