1.1 This test method covers the determination of the flexural properties of fiber-reinforced pultruded plastic rods. The specimen is a rod with a semicircular cross section, molded or cut from leng...
2009-09-01
1.1 This test method describes a procedure for the determination of beryllium, chromium, copper, manganese, nickel, lead, vanadium, and zinc in coal ash or coke ash. 1.2 This standard does not purpo
2011-05-20
1.1 This guide covers procedures and test methods that can be used in the evaluation of the ability of the clay portion of a geosynthetic clay liner to resist change due to exposure to liquids. The...
2009-11-01
1.1 This test method determines the snagging resistance of a fabric. 1.2 Studies of fabric snagging have sho
2013-03-25
1.1 This test method covers the determination of the alteration in shade of the textile portion of zippers when exposed to light, regardless of the materials of manufacture. 1.2 The values stated ...
2004-10-01
1.1 This test method covers a simple procedure for the detection of enterococci in water and wastewater. It is based on IDEXX's patented Defined Substrate Technology (DST). This product, Enteroler...
2005-06-01
1.1 This practice covers a protocol for the assessment of resistance of medical glove materials to permeation by potentially hazardous cancer chemotherapy drugs under conditions of
2005-04-01
1.1 This standard covers terminology relating to industrial and specialty chemicals. It is intended to provide an understanding of terms commonly used in test methods, practices, and specifications...
2009-04-01
1.1 This specification covers aluminum alloys in the 8000 series cited in B8 This specification covers aluminum alloys in the 8000 series in tempers ?0? and H1X or H2X bare compact-round...
2007-12-05
1.1 This test method covers a procedure for determining the maximum media density for purposes of estimating the maximum dead load for green roof assemblies. The method also provides a measure of t...
2011-09-16
1.1 This guide is intended to be used by architects, engineers, specifiers, contractors, and material suppliers who design, select, specify, install, purchase, fabricate, or suppl
2012-02-24
1.1 This test method is used to indicate the presence of capillary moisture in concrete. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses a...
2005-09-01
1.1 This test method covers the determination of asphalt fume particulate matter (as benzene soluble fraction) and total particulate matter weight in workplace atmospheres using a polytetrafluoroet...
2004-04-01
1.1 This specification covers fine silver grade 99.9 % in fabricated form. The forms covered are tubing, rod, wire, strip, and sheet for electrical contact applications. 1.2 The electrical conta...
2006-06-01
1.1 This standard practice describes a hierarchical outline of sections and elements to be used in developing metadata to support archived data management systems. Specifically, th
2005-10-01
1.1 When an observer looks through an aerospace transparency, relative optical distortion results, specifically in thick, highly angled, multilayered plastic parts. Distortion occurs in all transpa...
1.1 This test method covers the analysis for the apparent sodium toluene sulfonate (NaTS) content of detergents. 1.2 The values stated in SI units are to be regarded as standard. No other units of ...
2009-10-01
1.1 This standard establishes lot or batch sampling plans and procedures for inspection by attributes using MIL-STD-105E as a basis for sampling a steady stream of lots indexed by AQL. 1.2 Thi...
1.1 This test method determines the antibacterial activity and persistence of test formulations, as measured by the inhibition of a test organism on an agar surface exposed to test sites on hum...
2010-05-17
1.1 This practice covers standardized procedures utilizing the electric or electronic typewriter as an imaging device for measuring the performance properties of carbonless paper, carbon paper, in...
1.1 This specification describes glass covers and slides for use in routine microscopy. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included ...
2005-05-01
1.1 This test method covers the procedure for determining the relative tinting strength of waterbased ink systems using a computer-aided spectrophotometer. 1.2 This test method is applicable to wat...
1.1 This practice covers the collection, dissolution, and determination of trace metals in workplace atmospheres, by flame atomic absorption spectrophotometry. 1.2 The sensitivity, detection limit...
2007-01-11
1.1 This test method covers the determination of chromic oxide in chrome tanning liquors, either simple, with added aluminum or zirconium, or with the usual masking complexing agents. 1.2 The value...
2011-03-18
1.1 This test method (1, 2, 3) is intended for the numerical estimation of dirt in paper or paperboard in terms of equivalent black area. This test method is satisfactory only for the estimation of...
1997-12-10
2010-08-01
1.1 This test method covers the recommended procedure for the determination of the nonvolatile or total solids content of liquid phenolic resins used for wood laminating.
1.1 Intent: 1.1.1 This guide covers equipment used in shielded cell or canyon facilities for the processing of nuclear and radioactive materials. It is the intent of
2006-01-01
1.1 This test method covers the beta backscatter gages for the nondestructive measurement of metallic and nonmetallic coatings on both metallic and nonmetallic substrate materials. 1.2 The test m...
2003-10-01
1.1 This test method covers the determination of chlorine in organic compounds by sodium peroxide bomb ignition. It is intended for application to samples of organic materials containing more than ...
1.1 This practice is intended to assist in the selection of sorbents and procedures for the sampling and analysis of ambient (1) , indoor (2) and workplace (3, 4)
2003-05-10