1.1 This test method covers a four-stroke cycle diesel engine test procedure for evaluating engine oils for certain high-temperature performance characteristics, particularly ring sticking, ring an...
2010-09-17
1.1 This test method measures air-leakage rates through a building envelope under controlled pressurization and de-pressurization. 1.2 This test method is applicable to small temperature differenti...
2010-01-15
1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both. ...
2009-12-01
1.1 This specification defines classification, materials, test requirements, inspection certification, marking and packaging of fittings for use with gasketed mechanical couplings complying to Spec...
2007-02-07
1.1 This test method covers the precise on-line determination of pH in water samples of conductivity lower than 100 μS/cm (see Table 1 and Table 2) over the pH range of 3 to 11 (see Fig...
2009-10-01
1.1 This test method is an accelerated procedure to determine the effectiveness of latex coatings at preventing the migration of tannin stains from wood substrates. <div
2008-06-01
1.1 This guide is intended for use in selecting terminology, measurement scales, and instrumentation for describing or evaluating such appearance characteristics as glossiness, opacity, lightness, ...
2003-01-10
2012-04-13
1.1 This practice specifies the fundamental parameters of computed radiography systems to assure satisfactory and repeatable results for nondestructive testing. 1.2 This practice describes the eval...
2005-06-01
1.1 This practice covers test conditions and procedures for xenon-arc exposures according to Practices G151 and <a href="http://myastm.astm.org/SUBSCRIP
2011-05-20
1.1 This specification covers liquids for use in paints, varnishes, enamels, and similar organic coatings and are solutions of metallic salts of: This specification covers the general r...
2007-09-05
1.1 This classification system covers syndiotactic polystyrene materials including homopolymer, copolymers, blends, and impact modified, suitable for molding and extrusion. Recycled product will be...
1.1 This test method establishes the requirements for the determination of the angle of twist in rectangular and square copper and copper alloy tube. 1.2 The values stated in inch-pound units are...
2009-04-01
1.1 The purpose of this guide is to establish requirements for all individuals engaged in forensic psychophysiological detection of deception (PDD). 1.2 All individuals engaged in the practice of c...
2011-09-16
1.1 This practice covers procedures for sampling and handling naphthalene, maleic anhydride, and phthalic anhydride in various solid forms, and as liquids at elevated temperatures in a safe manne...
2010-08-20
1.1 This specification covers burst disk assemblies for paintball marker propellant sources their application and installation requirements. 1.2 The values stated in SI units are to be regarded as ...
1.1 This standard test method uses a simulated in-use study to measure the drop size by weight and to determine the number of drops per container for solutions and suspensions contained in a packa...
2004-10-01
2010-04-01
1.1 This practice covers the procedure for preparing prints of paste inks using a hand operated flat-bed laboratory proof press. The initial method was developed by the National Printing Ink Resear...
2011-03-18
1.1 This test method covers a comparative procedure for observing the characteristic and residual odors of volatile organic solvents and diluents to determine their odor acceptabil
1.1 This test method covers the testing of components for total hydrocarbons (THC) contribution to a gas distribution system at ambient temperature. In addition, this test method a
2005-01-01
1.1 This test method provides dc hysteresigraph procedures (B-H loop methods) for the determination of basic magnetic properties of materials in the form of ring, toroidal, link, double-lapped E...
2001-06-10
1.1 This test method covers calculation of the percent of primary, secondary, and tertiary amines in the sample from determinations of primary, secondary, and tertiary amine values and percent of n...
1992-01-01
2007-03-20
1.1 This test method determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers. The composite material forms are limited...
1.1 This guide is intended to help ASTM technical committees determine when it is appropriate to add supplementary requirements (see Section B24 of Form and Style for ASTM Standards) to ASTM standa...
2002-10-10
2007-03-01
1.1 This specification covers requirements for autocatalytic (electroless) nickel-phosphorus coatings applied from aqueous solutions to metallic products for engineering (functional) uses. 1.2 The...
2004-08-01
1.1 This specification covers requirements, test methods, and materials for 4 to 48 in. diameter poly(vinyl chloride) (PVC) corrugated pipe with a smooth interior. This profile wall pipe consists ...
2010-02-01
1.1 This specification covers cooktops which utilize induction as a means for cooking and warming food in commercial and institutional food service establishments. Included are tabletop units, drop...
2010-05-01
1.1 This practice covers the procedure for radiographic testing of cast metallic surgical implants and related weldments. 1.2 The values stated in inch-pound units are to be regarded as standard. T...
2012-01-20
1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference material. It is applicable to the following types of polishes: 1.1.1 W...
1997-08-28
1.1 This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers su...
2007-01-01
1.1 This test method covers the determination of corrosion- preventive properties of greases using grease- lubricated ball bearings under dynamic wet conditions. 1.2 The values stated in SI units ...