21300 träffar på

Standard · ASTM ASTM F2212 Standard Guide for Characterization of Type I Collagen as Starting Material for Surgical Implants and Substrates for Tissue Engineered Medical Prod... 1.1 This guide for characterizing collagen-containing biomaterials is intended to provide characteristics, properties, and test methods for use by producers, manufacturers, and researchers to more ... Språk Publicerad 2011-05-20

PDF · 611 SEK

Standard · ASTM ASTM E2232 Standard Guide for Selection and Use of Mathematical Methods for Calculating Absorbed Dose in Radiation Processing Applications 1.1 This guide describes different mathematical methods that may be used to calculate absorbed dose and criteria for their selection. Absorbed-dose calculations can determine the effectiveness of t... Språk Publicerad 2010-10-15

PDF · 611 SEK

Standard · ASTM ASTM C141/C141M Standard Specification for Hydrated Hydraulic Lime for Structural Purposes 1.1 This specification covers hydrated hydraulic lime for structural purposes. 1.2 Hydrated hydraulic lime may be used in the scratch or brown coat of plaster, stucco, mortar, or in portland-cement... Språk Publicerad 2009-10-01

PDF · 468 SEK

Standard · ASTM ASTM D4071 Standard Practice for Use of Portland Cement Concrete Bridge Deck Water Barrier Membrane Systems 1.1 This practice covers liquid applied, preformed, or built-up water barrier membrane systems and their application; overlaid with bituminous concrete wearing courses, for use in the protection of... Språk Publicerad 2005-06-01

PDF · 468 SEK

Standard · ASTM ASTM D3847 Standard Practice for Rubber&mdash;Directions for Achieving Subnormal Test Temperatures 1.1&#x00a0;This practice covers the general requirements for achieving and maintaining temperatures below 21&#x00b0;C for thermal conditioning and physical testing of rubber. <d Språk Publicerad 2007-09-05

PDF · 468 SEK

Standard · ASTM ASTM C502 Standard Test Method for Wedging of Flat, Rectangular Ceramic Wall and Floor Tile 1.1 This test method covers the determination of the wedging or deviation from rectangularity of flat, rectangular wall and floor tile. The test method covers tile as defined in Terminology C 242. 1 Språk Publicerad 2009-01-01

PDF · 468 SEK

Standard · ASTM ASTM C1490 Standard Guide for the Selection, Training and Qualification of Nondestructive Assay (NDA) Personnel 1.1 This guide contains good practices for the selection, training, qualification, and professional development of personnel performing analysis, calibration, physical measurements, or data review... Språk Publicerad 2004-02-01

PDF · 468 SEK

Standard · ASTM ASTM D5663 Standard Guide for Validating Recycled Content in Packaging Paper and Paperboard 1.1 This guide provides an approach for both the calculation and the substantiation of recycled content of finished packaging paper and paperboard products. A mass balance approach is recommended f... Språk Publicerad 1997-12-10

PDF · 533 SEK

Standard · ASTM ASTM D4555 Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test 1.1 This test method covers the measurement of the deformability and strength of large in situ specimens of rock by a uniaxial compressive test. The test results take into account the effect of bot... Språk Publicerad 2010-01-15

PDF · 533 SEK

Standard · ASTM ASTM F2389 Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems 1.1 This specification establishes requirements for polypropylene (PP) piping system components made to metric sizes and IPS schedule 80 sizes, and pressure rated for water service and distribution... Språk Publicerad 2010-02-01

PDF · 533 SEK

Standard · ASTM ASTM D2652 Standard Terminology Relating to Activated Carbon 1.1 This terminology covers terms particularly related to activated carbon and encompasses finished products, applications, and testing procedures. 1.2 When any of the definitions in this terminolo... Språk Publicerad 2011-09-16

PDF · 468 SEK

Standard · ASTM ASTM D4571 Standard Test Methods for Rubber Compounding Materials—Determination of Volatile Material 1.1 These test methods cover the determination of the loss of volatile materials in various rubber chemicals based on the mass loss upon heating at 70°C. 1.2 These test methods for the Språk Publicerad 2007-01-11

PDF · 468 SEK

Standard · ASTM ASTM D4481 Standard Test Method for Total Nickel in Fresh Alumina-Base Catalysts 1.1 This test method covers the determination of nickel in fresh alumina-base catalysts and has been tested at nickel concentrations from 2.5 to 60 weight %, expressed as nickel oxide (NiO). 1.2 Th... Språk Publicerad 2010-04-01

PDF · 468 SEK

Standard · ASTM ASTM D4740 Standard Test Method for Cleanliness and Compatibility of Residual Fuels by Spot Test 1.1 This test method covers separate procedures for determining the cleanliness of residual fuel oil and the compatibility of a residual fuel oil with a blend stock. It is applicable to residual f... Språk Publicerad 2004-06-01

PDF · 468 SEK

Standard · ASTM ASTM C272 Standard Test Method for Water Absorption of Core Materials for Sandwich Constructions 1.1 This test method covers the determination of the relative amount of water absorption by various types of sandwich construction core materials when immersed in water, or when subjected to a high... Språk Publicerad 2007-01-01

PDF · 468 SEK

Standard · ASTM ASTM B294 Standard Test Method for Hardness Testing of Cemented Carbides 1.1 This test method covers the hardness testing of cemented carbides by use of a Rockwell hardness tester performing tests in the Rockwell HRA scale (regular scale, diamond indenter, 10 kgf (98.07... Språk Publicerad 2010-08-20

PDF · 533 SEK

Standard · ASTM ASTM A958/A958M Standard Specification for Steel Castings, Carbon and Alloy, with Tensile Requirements, Chemical Requirements Similar to Standard Wrought Grades 1.1 This specification covers carbon and low-alloy steel castings having chemical analyses similar to that of the standard wrought grades. 1.2 Several classes are covered and are designated by chem... Språk Publicerad 2010-04-01

PDF · 533 SEK

Standard · ASTM ASTM F36 Standard Test Method for Compressibility and Recovery of Gasket Materials 1.1 This test method covers determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut fro... Språk Publicerad 2009-10-01

PDF · 468 SEK

Standard · ASTM ASTM C35 Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster 1.1 This specification covers perlite, vermiculite, natural and manufactured sand for use as gypsum plaster aggregates. 1.2 The values stated in inch-pound units are to be regarded as standard. The... Språk Publicerad 2005-10-01

PDF · 468 SEK

Standard · ASTM ASTM E636 Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels, E 706 (IH) 1.1 This guide discusses test procedures that can be used in conjunction with, but not as alternatives to, those required by Practices E185 and <a href= Språk Publicerad 2010-03-01

PDF · 533 SEK

Standard · ASTM ASTM E999 Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing 1.1 This guide establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aid in ... Språk Publicerad 2010-09-17

PDF · 533 SEK

Standard · ASTM ASTM D4318 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils 1.1 These test methods cover the determination of the liquid limit, plastic limit, and the plasticity index of soils as defined in Section 3 on Terminology. 1.2 Two methods for preparing test spec... Språk Publicerad 2010-01-15

PDF · 611 SEK

Standard · ASTM ASTM D4455 Standard Test Method for Enumeration of Aquatic Bacteria by Epifluorescence Microscopy Counting Procedure 1.1 This test method describes a procedure for detection and enumeration of aquatic bacteria by the use of an acridine-orange epifluorescence direct-microscopic counting procedure. It is applicable... Språk Publicerad 1985-01-25

PDF · 468 SEK

Standard · ASTM ASTM D558 Standard Test Methods for Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures 1.1 These test methods cover the determination of the relationship between the water content and the density of soil-cement mixtures when compacted before cement hydration as prescribed. 1.2 A... Språk Publicerad 2011-05-20

PDF · 533 SEK

Standard · ASTM ASTM D4577 Standard Test Method for Compression Resistance of a Container Under Constant Load 1.1 This test method is designed to determine the resistance of a shipping container to a vertically applied constant load for either a specified time or to failure. The test method may also be us... Språk Publicerad 2005-10-01

PDF · 533 SEK

Standard · ASTM ASTM D5274 Standard Guide for Analysis of 1,3-Butadiene Product 1.1 This guide covers the analysis of 1,3–butadiene products produced in North America. It includes possible components and test methods, both ASTM and other, either actually used or be... Språk Publicerad 2005-11-01

PDF · 468 SEK

Standard · ASTM ASTM D3709 Standard Test Method for Stability of Water-in-Oil Emulsions Under Low to Ambient Temperature Cycling Conditions 1.1 This test method covers the indication of the stability of water-in-oil emulsions when subjected to temperature cycling changes between ambient temperature and &#x2013;18&#x00B0;</span Språk Publicerad 2010-10-01

PDF · 468 SEK

Standard · ASTM ASTM B271 Standard Specification for Copper-Base Alloy Centrifugal Castings 1.1 This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1. 1.2 The values stated in either SI units or inch-po... Språk Publicerad 2011-12-16

PDF · 533 SEK

Standard · ASTM ASTM D2339 Standard Test Method for Strength Properties of Adhesives in Two-Ply Wood Construction in Shear by Tension Loading 1.1 This test method covers the determination of the comparative shear strengths of adhesives when tested on a standard specimen and under specified conditions of preparation, conditioning, and te... Språk Publicerad 2004-04-01

PDF · 468 SEK

Standard · ASTM ASTM D1060 Standard Practice for Core Sampling of Raw Wool in Packages for Determination of Percentage of Clean Wool Fiber Present 1.1 This practice for sampling covers a procedure for obtaining samples from lots of grease, pulled, or scoured wool or related animal fibers in bales or bags for the determination of the clean wo... Språk Publicerad 2010-06-01

PDF · 533 SEK

• < Föregående
• 481
• 482
• 483
• 484
• 485
• 486
• 487
• 488
• 489
• 490
• Nästa >