1.1 This guide covers two distinct procedures, based on similar principles, for obtaining data concerning the adverse effects of a test material (added to dilution water) on oceani
2004-08-01
2013-03-19
1.1 The test method covers a heavy-duty diesel engine test procedure conducted under high soot conditions to evaluate oil performance with regard to valve train wear, top ring wear
2013-03-25
1.1 This specification covers electrical insulating tape consisting of a backing made from polyethylene plastic film, coated on one side with a pressure-sensitive adhesive. 1.2 The values stated i...
2010-08-20
1.1 This test method covers a wide range of alcohols with various structures and boiling points that can be separated and detected quantitatively in water and waste water at a mini
2008-02-06
1.1 This specification covers materials, structural design, physical dimensions and manufacturing requirements for monolithic or sectional corrugated high density polyethylene (HDPE) water quality ...
2012-02-24
1.1 This specification covers a lubricant suitable for facilitating the insertion and positioning of preformed elastomeric compression seals in prepared voids (usually contraction joints This speci...
2008-03-12
1.1 This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service as listed in Table 1. (Although no restrictions are placed on the sizes of pipe that m...
2009-10-01
1.1 This specification covers concentric-lay-stranded conductors made from round aluminum 1350-H19 (extra hard) wires and round aluminum-alloy 6201-T81 (hard: solution heat treated, cold worked, a...
2005-03-01
1.1 This test method (Note 1) covers the determination of the iodine value of fatty amines, diamines, and amidoamines by the Wijs procedure. Note 1-This test method is essentially equivalen...
1992-01-01
2007-03-20
1.1 This test method , simulates in a qualitative manner the forces and effects on an adhesive bond joint at metal-adhesive/primer interface. It has proven to be highly reliable in determining and...
2003-08-10
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, stiffness factor, extrusion quality, and a form of marking for extruded poly(vinyl chloride) (PV...
2009-04-01
1.1 This specification covers leather protector gloves and leather protector mittens to be worn over electrical workers' rubber insulating gloves and rubber insulating mittens. 1.2 It is intended ...
2006-11-01
1.1 This terminology and acronyms standard covers and defines commonly used terms and acronyms in the field of corrosion. Related terms may be found in Terminologies <a href="http://myastm.astm....
2011-10-14
1.1 This test method covers the determination of long polystyrene blocks in SBR rubbers and styrene-reinforced latices. 1.2 Percent block styrene content may be determined in the range from 1 to 10...
2006-10-01
1.1 This specification covers ductile iron castings for use in pressure containing paper mill dryer rolls at temperatures up to 450°F [230°C]. 1.2 No This specification covers...
1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine...
2010-09-17
1.1 This test method describes a laboratory procedure for the determination of rheological (flow) properties of single- and multicomponent chemically curing sealants for use in building constructio...
2007-09-05
1.1 This practice covers a calibration technique based on the preparation of standards of known water content. This technique is applicable to the production of standards between 20 and 2000 cm3/m...
2005-11-01
1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The p...
2011-05-20
1.1 This practice covers the procedure for the separation of the vehicle from the pigment in solvent-reducible paint. 1.2 In the development of the practice the following materials were tested: w...
2010-06-01
1.1 These test methods cover the determination of the relationship between the water content and the density of soil-cement mixtures when compacted before cement hydration as prescribed. 1.2 A...
1.1 This practice covers the calculation of low-temperature properties of asphalt binders using data from the bending beam rheometer (see Test Method D 6648) (BBR) and the direct tension tester (se...
2002-07-10
2011-04-08
1.1 This specification covers minimum requirements for cellulose fibers intended for use in fiber-reinforced concrete, and other cementitious products. <div class="SectionLevel
1.1 This practice provides recommendations for the installation of buried thermoplastic pipe used in sewers and other gravity-flow applications. These recommendations are intended to ensure a stab...
1.1 This specification covers the requirements for HFC-125 as a fire–fighting medium. 1.2 This specification does not address the fire–fighting equip This specification covers...
1.1 This test method covers the determination of the percent benzene in full-range gasoline. It is applicable to concentrations from 0.1 % to 5 volume %. 1.2 This test method has not been validate...
2004-11-01
1.1 This specification covers nickel-chromium-molybdenum-tungsten (UNS N06110) in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1. 1.2 The values state...
2006-06-01
1.1 This test method covers an analytical scheme using the mass spectrometer to determine the hydrocarbon types present in virgin middle distillates 204 to 343°C (400 to 650°<
1.1 This practice covers the selection and application temperatures of road tar grades in the construction and maintenance of pavements. 1.2 The values stated in SI units are to be regarded as sta...
2009-12-01
1.1 This test method covers determination of the thermal endurance of film-insulated round magnet wire in air at atmospheric pressure. It is not applicable to magnet wire with fibr
2007-05-09