21325 träffar på

Standard · ASTM ASTM D4966

Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method)

1.1 This test method covers the determination of the abrasion resistance of textile fabrics using the Martindale abrasion tester. Fabrics of all types may be tested by this method but difficulties ...

Språk

Publicerad

2012-03-23

PDF · 468 SEK

Standard · ASTM ASTM D7041

Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels, and Oils by Online Gas Chromatography with Flame Photome...

1.1 This test method covers the determination of total sulfur in liquid hydrocarbons with a final boiling point less than 450°C by gas chromatography using a flame photometric detector. ...

Språk

Publicerad

2004-07-01

PDF · 533 SEK

Standard · ASTM ASTM A840

Standard Specification for Fully Processed Magnetic Lamination Steel (Withdrawn 2011)

1.1 This specification covers cold-rolled carbon steel coils or strip used in the fully processed condition in magnetic lamination applications.1.2 This steel is produced to specified maximum core-...

Språk

Publicerad

2006-11-15

Upphävd

2011-05-01

PDF · 468 SEK

Standard · ASTM ASTM D4845

Standard Terminology Relating to Wool

Språk

Publicerad

2010-09-17

PDF · 533 SEK

Standard · ASTM ASTM C78/C78M

Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)

1.1 This test method covers the determination of the flexural strength of concrete by the use of a simple beam with third-point loading. 1.2 The values stated in either SI units or inch-pound uni...

Språk

Publicerad

2010-08-01

PDF · 468 SEK

Standard · ASTM ASTM B857

Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Supported (ACSS/TW)

1.1 This specification covers shaped wire compact concentric-lay-stranded aluminum conductors, steel supported (ACSS/TW) for use as overhead electrical conductors (see Explanatory Note 1). 1.2 The...

Språk

Publicerad

2011-09-16

PDF · 533 SEK

Standard · ASTM ASTM A307

Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

1.1 This specification covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes 1/4 in. through 4 in. The fasteners are designated by "Grade" denotin...

Språk

Publicerad

2007-09-05

Upphävd

2010-10-01

PDF · 533 SEK

Standard · ASTM ASTM A307

Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

1.1 This specification covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes ¼ in. through 4 in. The fasteners are designated by Thi...

Språk

Publicerad

2011-03-18

Upphävd

2012-12-01

PDF · 533 SEK

Standard · ASTM ASTM A358/A358M

Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applicat...

1.1 This specification covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications. N...

Språk

Publicerad

2008-12-15

Upphävd

2012-12-01

PDF · 533 SEK

Standard · ASTM ASTM C602

Standard Specification for Agricultural Liming Materials

1.1 This specification covers agricultural liming materials, such as quicklime (burnt lime), hydrated lime, limestone, (calcitic and dolomitic), marl, shells, and by-products including slag, and ot...

Språk

Publicerad

2007-09-05

Upphävd

2012-12-01

PDF · 468 SEK

Standard · ASTM ASTM D817

Standard Test Methods of Testing Cellulose Acetate Propionate and Cellulose Acetate Butyrate

1.1 These test methods cover procedures for the testing of cellulose acetate propionates and acetate butyrates. These esters may vary widely in composition and properties, so certain of the procedu...

Språk

Publicerad

2010-06-01

Upphävd

2012-11-01

PDF · 611 SEK

Standard · ASTM ASTM D3786

Standard Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method

1.1 This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally applicable to...

Språk

Publicerad

2008-11-05

Upphävd

2009-07-01

PDF · 468 SEK

Standard · ASTM ASTM D5206

Standard Test Method for Windload Resistance of Rigid Plastic Siding

1.1 This test method describes methods for testing and evaluating windload resistance of rigid plastic siding when fastened in accordance with Practice D 4756. 1.2 The proper use of this test metho...

Språk

Publicerad

2007-02-07

Upphävd

2013-01-01

PDF · 468 SEK

Standard · ASTM ASTM D5426

Standard Practices for Visual Inspection and Grading of Fabrics Used for Inflatable Restraints

1.1 These practices cover procedures for the inspection and grading of coated and uncoated woven flat and one-piece woven (OPW) fabrics, and for the inspection and culling of cut parts made of such...

Språk

Publicerad

2008-11-05

Upphävd

2012-12-01

PDF · 533 SEK

Standard · ASTM ASTM D6477

Standard Terminology Relating to Tire Cord, Bead Wire, Hose Reinforcing Wire, and Fabrics

1.1 This terminology is the compilation of all definitions developed by Subcommittee D13.19 on Tire Cords and Fabrics. 1.2 The terminology, mostly definitions, is unique to the tire cord fabric ind...

Språk

Publicerad

2011-05-20

Upphävd

2013-01-01

PDF · 468 SEK

Standard · ASTM ASTM D6875

Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor

1.1 This test method covers a general procedure for determining the solidification point of most organic chemicals having appreciable heats of fusion and solidification points between 4 and 41&...

Språk

Publicerad

2008-10-01

Upphävd

2012-12-01

PDF · 468 SEK

Standard · ASTM ASTM D6999

Standard Practice for Miscibility of Emulsified Asphalts

1.1 This practice covers all medium and slow-setting emulsified asphalts. It is not applicable to the rapid-setting types. 1.2 This practice does not purport to address all of the safety concerns, ...

Språk

Publicerad

2004-08-01

Upphävd

2012-12-01

PDF · 468 SEK

Standard · ASTM ASTM D7184

Standard Test Method for Ultra Low Nitrogen in Aromatic Hydrocarbons by Oxidative Combustion and Reduced Pressure Chemiluminescence

1.1 This test method covers the determination of total nitrogen in aromatic hydrocarbons, such as benzene, toluene, and xylene.1.2 This test method is applicable for samples containing nitrogen fro...

Språk

Publicerad

2007-05-09

Upphävd

2012-12-01

PDF · 468 SEK

Standard · ASTM ASTM E572

Standard Test Method for Analysis of Stainless and Alloy Steels by X-ray Fluorescence Spectrometry

1.1 This test method covers the analysis of stainless and alloy steels by wavelength dispersive X-ray Fluorescence Spectrometry for the determination of the following elements:Note 1Unless exceptio...

Språk

Publicerad

2007-01-11

Upphävd

2012-12-01

PDF · 533 SEK

Standard · ASTM ASTM F459

Standard Test Methods for Measuring Pull Strength of Microelectronic Wire Bonds

1.1 These test methods cover tests to determine the pull strength of a series of wire bonds. Instructions are provided to modify the methods for use as a referee method. The methods can be used for...

Språk

Publicerad

2006-01-01

Upphävd

2013-01-01

PDF · 468 SEK

Standard · ASTM ASTM F487

Standard Specification for Fine Aluminum-1% Silicon Wire for Semiconductor Lead-Bonding

1.1 This specification covers aluminum-1 % silicon alloy wire for internal connections in semiconductor devices and is limited to wire of diameter up to and including 0.0020 in. (0.051 mm). For dia...

Språk

Publicerad

2006-01-01

Upphävd

2013-01-01

PDF · 468 SEK

Standard · ASTM ASTM F1414

Standard Test Method for Measurement of Cut Resistance to Chain Saw in Lower Body (Legs) Protective Clothing

1.1 This test method measures cut resistance of garments and devices worn to protect the lower (legs) body when operating a chain saw.1.2 This test method may be used to test for compliance to mini...

Språk

Publicerad

2004-10-01

Upphävd

2013-01-01

PDF · 611 SEK

Standard · ASTM ASTM F1818

Standard Specification for Foot Protection for Chain Saw Users

1.1 This specification covers minimum requirements for the design, performance, testing, and certification of footwear and foot protective devices designed to provide cut resistance protection to t...

Språk

Publicerad

2004-10-01

Upphävd

2013-01-01

PDF · 533 SEK

Standard · ASTM ASTM F1929

Standard Test Method for Detecting Seal Leaks in Porous Medical Packaging by Dye Penetration

1.1 This test method defines materials and a procedure that will detect and locate a leak equal or greater than a channel formed by a 50 μm (0.002 in.) wire in package edge seals formed be...

Språk

Publicerad

2004-06-01

Upphävd

2012-11-01

PDF · 468 SEK

Standard · ASTM ASTM F2865

Standard Guide for Classifying the Degrees of Ingression Protection Provided by a Membrane Switch

1.1 This guide establishes a classification system and references test methods for verifying the degrees of protection provided by a membrane switch against the following: 1.1.1 The ingress of ...

Språk

Publicerad

2012-02-24

Upphävd

2013-01-01

PDF · 468 SEK

Standard · ASTM ASTM E2371

Standard Test Method for Analysis of Titanium and Titanium Alloys by Atomic Emission Plasma Spectrometry

1.1 This method describes the analysis of titanium and titanium alloys by ICP-AES (Inductively Coupled Plasma) and DCP-AES (Direct Current Plasma) for the following elements:ElementApplicationRange...

Språk

Publicerad

2004-06-01

Upphävd

2013-01-01

PDF · 611 SEK

Standard · ASTM ASTM A182/A182M

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service

1.1 This specification covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions o...

Språk

Publicerad

2007-09-05

Upphävd

2008-03-01

PDF · 611 SEK

Standard · ASTM ASTM A182/A182M

Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Ser...

1.1 This specification covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions...

Språk

Publicerad

2011-09-16

Upphävd

2012-05-15

PDF · 611 SEK

Standard · ASTM ASTM C588/C588M

Standard Specification for Gypsum Base for Veneer Plasters (Withdrawn 2005)

1.1 This specification covers types of gypsum base that are designed to be used as a base for application of veneer plaster (see Specification C 587).Note 1—Specification C 843 contains a...

Språk

Publicerad

2007-01-11

Upphävd

2008-10-28

PDF · 468 SEK

Standard · ASTM ASTM A1008/A1008M

Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formabilit...

1.1 This specification covers cold-rolled, carbon, structural, high-strength low-alloy, high-strength low-alloy with improved formability, solution hardened, and bake hardenable steel sheet, in coi...

Språk

Publicerad

2011-05-20

Upphävd

2012-03-01

PDF · 533 SEK

Förfina din sökning genom att visa:

...som handlar om: