1.1 This practice covers procedures for the verification and classification of extensometer systems, but it is not intended to be a complete purchase specification. The practice is applicable only...
2010-09-17
1.1 This practice covers requirements for the handling of all bearings and bearing components. 1.2�
2004-11-01
1.1 This specification covers the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only...
2003-10-01
1.1 This test method covers the determination of the purity of methyl ethyl ketone by gas chromatography. Impurities including water, acidity, and nonvolatile matter are measured b
2007-09-05
1.1 This test method covers all degraded glycerides, since they are neutral fats. However, this procedure does not necessarily determine all the mono and diglycerides that may be present in the sam...
2006-04-01
1.1 This test method covers the determination of the transverse rupture strength of cemented carbides. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values i...
2005-10-01
1.1 This specification covers UNS N08367* welded tube for general corrosion applications. 1.2 This specification covers outside diameter and nominal wall tube. 1.2.1 The tube sizes covered by thi...
2003-11-01
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weig...
1.1 This specification covers detailed requirements for cantilever and overhead slide chain link fence gates, gate posts, and accessories for industrial and commercial applications. 1.2 The values ...
2005-07-01
1.1 The table provides a standard ultraviolet spectral irradiance distribution that maybe employed as a guide against which manufactured ultraviolet light sources may be judged whe
2008-06-01
1.1 This test method describes the measurement of fiber cohesion as the force required to cause initial drafting in a bundle of fibers in sliver and top. The observed cohesive force required to se...
2005-04-01
1.1 This specification provides the minimum requirements for design fabrication, pressure rating, and testing for line-blind valves. 1.2 The values stated in inch-pound units are to be regarded a...
2006-02-01
1.1 These test methods cover the preparation of a standard-size test sample and basic tests for physical property determinations of microcellular urethane materials. 1.2 The values stated in SI un...
2012-02-24
1.1 This test method covers the determination of the total nonaromatic hydrocarbons, and trace monocyclic aromatic hydrocarbons in the purity of toluene and mixed xylenes by gas chromatograp...
2011-09-16
1.1 This test method covers a rapid procedure for determining the rate of water vapor transmission of flexible barrier materials in film or sheet form. This test method is applicable to sheets and ...
1999-05-10
2009-05-15
1.1 This specification covers concrete drain tile with internal diameters from 100 to 900 mm, that are intended to be used for surface and subsurface drainage. 1.2 This specification is the metric ...
2011-11-18
1.1 This test method covers the procedure for obtaining and analyzing pavement macrotexture profiles using the Circular Track Meter (CTMeter). 1.2 The CTMeter consists of a charge coupled device (C...
2009-11-01
1.1 This practice describes a method for direct sampling and analysis of process vents for volatile organic compound (VOC) vapors and permanent gases using a portable gas chromatograph (GC). 1.2 Th...
2009-10-01
1.1 This test method covers the determination of titanium dioxide content in liquid paint. This test method is applicable to both water-reducible and solvent-reducible paints.<
2006-06-01
1.1 This test method covers determination of the flexural strength of manufactured carbon and graphite articles using a simple beam in four-point loading at room temperature. 1.2 The values state...
2011-08-25
1.1 These test methods cover procedures for the determination of the resistance of stainless steels and related alloys to pitting and crevice corrosion (see Terminology <a href="http://myastm....
2011-10-14
1.1 This practice describes the proper procedures for preserving zooplankton samples with either formaldehyde, ethanol, glutaraldehyde, Lugol's iodine solution, or vinegar (
2004-04-01
1.1 This specification covers performance requirements for helmets manufactured for users of electric personal assistive mobility devices. 1.2 All testing and requirements of this specification sha...
2006-05-01
1.1 This test method covers the determination of residual strength of a fiber–reinforced concrete test beam. The average residual strength is computed using specified beam deflections t...
2011-05-20
1.1 This practice covers the procedure for sampling stratified or un-stratified waters and liquid waste using bailers. 1.2 Three specific bailers are discussed in this practice. The bailers are the...
1.1 This practice covers the material and fabrication of a Beam Purity Indicator (BPI), which can be used to determine the relative quality of radiographic images produced by direct, thermal neutro...
2010-01-01
1.1 This specification covers compression molding, thermosetting, unsaturated polyester molding compounds as further defined in This specification deals with the classification, requirem...
2004-10-01
1.1 This practice covers two procedures applicable to all adhesives having a relatively short working life. It is intended to determine whether the working life conforms to the minimum specified wo...
1.1 This guide describes procedures for conducting controlled experiments with caged bivalves under field conditions. The purpose of this approach is to facilitate the simultaneous
2007-12-05
1.1 This practice covers a process for conducting a Phase II environmental site assessment (ESA) of a parcel of property with respect to the presence or the likely <span class="italic