1.1 This test method covers the determination of the number of actuations required to prime a pump dispenser (spray and flow types) with a consumer-type product. 1.2 This standard does not purport to
2005-10-01
1.1 This test method describes the procedure for evaluating the relative cure of printed energy-cured (ultraviolet or electron beam) ink or coating by a mechanical solvent rub test using a motori...
2007-01-11
1.1 These test methods cover the determination of volatile loss from a plastic material under defined conditions of time and temperature, using activated carbon as the immersion medium. 1.2 Two tes...
2011-04-15
1.1 This specification covers designations, dimensions, and tolerances for only the ground surfaces of interchangeable taper-ground joints for laboratory and industrial equipment i This ...
2002-10-10
1.1 This test method covers household types of upright, canister, and combination vacuum cleaners. 1.2 This test method provides a measurement in dry quarts or litres of the maximum functional volu...
2006-04-01
1.1 This specification covers aluminum-alloy (Note 1) die forgings, hand forgings, and rolled ring forgings as shown in Table 1, Table 2 and Table 3 and in Section 10 for heat-treatable alloy forgi...
2009-09-01
1.1 This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified ther...
2009-04-01
1.1 This practice covers a means of measuring the amount of heat transfer quantitatively through a material or system. 1.2 This practice is similar to the Heat Flow Meter System of Test Method C 518,
1.1 This test method describes a procedure for determining the effect of exposure to alkaline environments on the strength of cellulose fibers. An alkaline environment is defined t
2008-06-01
1.1 This test method covers a measurement of the oxidation stability of biodiesel (B100) blendstock as specified in Specification D6751 and blends of
2011-05-20
1.1 This test method covers a rapid procedure for conversion of animal and vegetable fatty oils into methyl esters of the fatty acids suitable for analysis by gas-liquid chromatography. 1.2 This ...
1998-10-10
2007-03-20
1.1 These alternative test methods cover the indicator procedure for determining the total, primary, secondary, and tertiary amine values of fatty amines. These procedures are not applicable to fat...
1992-01-01
1.1 This test method covers the measurement of thickness of any nonmagnetic material by means of a digital magnetic intensity instrument.Note 1The instrument on which this test method is based is n...
2004-10-01
2008-08-18
1.1 These test methods determine the constituent content of composite materials by one of two approaches. Test Method I physically removes the matrix by digestion or ignition by one of seven proced...
2011-12-16
1.1 These practices cover the calculation of truck response to longitudinal profiles of traveled surface roughness. 1.2 These practices utilize computer stimulations to obtain two truck responses i...
2003-12-01
1.1 This test method determines the resistance of a stretch wrap film to the penetration of a probe at a standard low rate, a single test velocity. Performed at standard conditions, the test method...
2007-09-05
1.1 This specification covers the procedures and acceptance standards for the determination of reduction of area using a tension test specimen whose axis is perpendicular to the rolled surfaces of...
2007-11-01
1.1 This specification covers fittings and single and coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe (DWV) made to Schedule 40 iron pipe sizes (IPS). Plastic...
2011-09-16
1.1 This test method covers the determination of the hydraulic conductivity (permeability) of essentially saturated, intact cylindrical specimens of peat when the hydraulic conductivity is greater ...
2012-02-24
1.1 This specification covers the chemical and physical requirements of municipal ferrous scrap that are intended for use by such industries listed as follows: 1.1.1 Copper industry (precipitation...
2010-10-01
1.1 This test method covers the evaluation of the force required to remove the hood and the actuator from a mechanical dispensing pump. 1.2 This standard may involve hazardous materials, operations, a
2006-07-15
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral gran...
2010-07-01
1.1 This test method covers the reverberation room measurement of the noise reduction of sound-isolating enclosures. 1.2 The noise isolation class may be determined from the noise reduction measure...
1996-01-10
1.1 This specification covers an iron-nickel-cobalt alloy, UNS K94610 containing nominally 29 % nickel, 17 % cobalt, and 53 % iron, in the forms of wire, rod, bar, strip, sheet, and tubing, i...
2009-12-01
1.1 This practice covers the materials, processes, and quality controls to be used in the manufacture of adhesive-bonded, aluminum-faced, foam core sandwich panels for tactical shelters. 1.2 The v...
2009-11-01
1.1 This terminology covers definitions for approved standards under the jurisdiction of ASTM Committee E17 on Vehicle-Pavement Systems. Definitions of terms specific to an individual st
2007-02-07
1.1 This specification provides the chemical and physical requirements for nuclear-grade aluminum oxide powder intended for fabrication into shapes for nuclear applications. Two specific uses for w...
2011-03-18
1.1 This specification covers the special requirements for valves used in gaseous oxygen service. It is intended that this specification be invoked as an additional requirement in conjunction with ...
2004-05-01
1.1 This test method covers the determination of benzene and toluene in finished motor and aviation gasolines by gas chromatography. 1.2 Benzene can be determined between the levels of 0.1 and 5 vo...
1.1 This test method covers the determination of 67 elements in uranium dioxide samples and nuclear grade uranium compounds and solutions without matrix separation by inductively coupled plasma mas...
2010-09-17