1.1 This test method covers the evaluation of the leakage tendencies of wheel bearing greases when tested under prescribed laboratory conditions.1.2 The values stated in SI units are to be regarded...
2005-05-01
2010-05-01
1.1 This test method covers procedures concerning site preparation, technical procedures, quality control, and equipment to direct the efforts for determining volumes of bulk material. These proced...
2004-04-01
1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in sheet resilient flooring sealed with liquid seam sealers. 1.2 This standard do
2007-09-05
1.1 These test methods cover the quantitative determination of total oxygen in gasoline and methanol fuels by reductive pyrolysis. 1.2 Precision data are provided for 1.0 to 5.0 mass % oxygen in ga...
1.1 This test method covers both the preparation procedure for samples containing free water (air drying loss (ADL) on gross moisture samples) and the determination of the gross moisture content of...
2006-07-01
1.1 This practice covers instructions for the designation of yarn construction and is applicable to single yarns, plied yarns, and cabled yarns or cords of filaments or spun fibers. The application...
2005-04-01
1.1 This classification covers the method for determining and classifying the resistance of poly(vinyl chloride) (PVC) homopolymer and copolymer compounds, and chlorinated poly(vinyl chloride) (CPV...
2004-02-01
1.1 This test method is commonly referred to as the Cummins M11 Exhaust Gas Recirculation Test (EGR). The test method defines a heavy-duty diesel engine test procedure conducted under high soot con...
2004-11-01
1.1 This practice covers and provides guidance for the material recovery of scrap tires for their fuel value. The conversion of a whole scrap tire into a chipped formed for use as
2006-05-01
1.1 This test method covers the stability of a compost sample by measuring oxygen consumption after exposure of the test compost to a well-stabilized compost under controlled-composting conditions...
1996-08-10
1.1 This guide along with Guide E1192 and guidance from the U.S. Enviro
2004-07-01
1.1 This test method covers determination of skeletal density of metal powders. The test method specifies general procedures that are applicable to many commercial pycnometry instruments. The metho...
2010-08-20
1.1 This test method covers the determination of the temperature at which liquids and solids will spontaneously ignite. These materials must ignite without application of spark or flame in a high-p...
2009-10-01
1.1 This practice provides test and measurement details for measuring the performance of X-ray and Gamma ray radioscopic systems. Radioscopic examination applications are diverse. Therefore, system...
2009-07-01
1.1 This specification covers glacial acrylic acid (99.0 % grade) for use in paint, varnish, lacquer and related products. 1.2 The following applies to all specified limits in this standard;...
2009-06-01
1.1 This specification covers gray iron castings that are statically cast in permanent molds. 1.2 No precis This specification covers gray iron castings that are statically cast in permanent mold...
2008-10-01
1.1 This test method covers the determination of pitch density by helium pycnometer. It is applicable at a range of room temperatures of 15 to 35°C. 1.2 The values stated in SI units a
1.1 This practice covers the selection and application temperatures of road tar grades in the construction and maintenance of pavements. 1.2 The values stated in SI units are to be regarded as sta...
2009-12-01
1.1 This guide applies only to existing historic masonry construction. For purposes of this guide historic masonry is intended to refer to buildings that have significant historic, architectural, c...
2003-02-10
1.1 This guide covers procedures that can be employed to mechanically attach fabricated geomembranes to structures, pipes, etc. 1.2 This guide does not address all problems or situations a geomembr...
2002-01-10
1.1 This practice covers the procedure for removing small quantities of ignitable liquid residue from samples of fire debris using solvent to extract the residue. 1.2 This practice is suitable fo...
2011-05-20
1.1 This specification covers the pigments commercially known as raw sienna and burnt sienna. This specification establishes the properties and requirements for the pigments commercially known as ...
2003-10-01
1.1 This test method covers the effects of repeated insertion and withdrawal of separable electrical connectors which are harmful to the electrical performance of the connector. 1.2 This test...
2003-06-10
1.1 These test methods cover testing of single-filament steel wires that are components of tire beads used in the manufacture of pneumatic tires. By agreement, these test methods may be applied to ...
2004-10-01
1.1 This specification covers concrete drain tile with internal diameters from 4 to 36 in. that are intended to be used for surface and subsurface drainage. 1.2 A complete metric companion to Spec...
2011-11-18
1.1 This test method describes how to estimate the relative resistance to deterioration of adhesive films and adhesive-bonded joints placed in a high-pressure oxygen environment. The instructions i...
1.1 This (laboratory) test method is used for determining the minimum concentration of fungicide, or formulation of fungicides, that is effective in preventing biodeterioration by sapstain fungi an...
2010-03-01
1.1 This guide covers a review of methods for sampling groundwater at discrete points or in increments by insertion of sampling devices by static force or impact without drilling a
2005-02-01
1.1 This specification covers heat resistant aluminum-zirconium alloy round wire for electrical purposes. There is a family of aluminum-zirconium alloys that are used for heat-resistance (i.e. re...
2011-04-15
1.1 This specification covers the requirements for electrical liquid level indicating equipment for shipboard low pressure and high pressure tanks containing freshwater, feed water, potable water, ...
2000-07-10
2009-03-05