21296 träffar på

Standard · ASTM ASTM D4124

Standard Test Methods for Separation of Asphalt into Four Fractions

1.1 These test methods cover the separation of four defined fractions from petroleum asphalts. The four fractions are defined as saturates, naphthene aromatics, polar aromatics, and nC7-asphaltenes...

Språk

Publicerad

2001-08-10

Upphävd

2009-07-01

PDF · 533 SEK
Standard · ASTM ASTM D5100/D5100M

Standard Test Method for Adhesion of Mineral Aggregate to Hot Bitumen

1.1 This test method determines the adhesion of mineral aggregate when applied over a pour coat of hot bitumen on a roof membrane. 1.2 The values stated in either SI units or inch-pound units are t...

Språk

Publicerad

2010-07-01

PDF · 468 SEK
Standard · ASTM ASTM D5126/D5126M

Standard Guide for Comparison of Field Methods for Determining Hydraulic Conductivity in the Vadose Zone

1.1 This guide covers a review of the test methods for determining hydraulic conductivity in unsaturated soils and sediments. Test methods for determining both field-saturated and unsaturated hydra...

Språk

Publicerad

2010-08-01

PDF · 611 SEK
Standard · ASTM ASTM D5254/D5254M

Standard Practice for Minimum Set of Data Elements to Identify a Ground-Water Site

1.1 This practice covers what information should be obtained for any individual ground-water site, also known as monitoring location or sampling station. As used in this practice, a site is meant ...

Språk

Publicerad

2010-08-01

PDF · 533 SEK
Standard · ASTM ASTM D5409/D5409M

Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part Two-Physical Descriptors

1.1 This guide covers Part Two of three guides to be used in conjunction with Practice D5254 that delineates the data desirable to describe a ground-w

Språk

Publicerad

2010-08-01

PDF · 611 SEK
Standard · ASTM ASTM D5498

Standard Guide for Developing a Training Program for Coating Work Inspectors in Nuclear Facilities

1.1 This guide is intended to assist those responsible for developing a program for the indoctrination and training of inspection personnel for coating work in nuclear facilities.1.2 It is recogniz...

Språk

Publicerad

2001-06-10

Upphävd

2009-06-01

PDF · 468 SEK
Standard · ASTM ASTM D5827

Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography

1.1 This test method covers the chemical analysis of engine coolant for chloride ion by high-performance ion chromatography (HPIC). Several other common anions found in engine coolant can be determ...

Språk

Publicerad

1995-09-10

Upphävd

2009-03-01

PDF · 533 SEK
Standard · ASTM ASTM D5827

Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography

1.1 This test method covers the chemical analysis of engine coolant for chloride ion by high-performance ion chromatography (HPIC). Several other common anions found in engine coolant can be determ...

Språk

Publicerad

2009-03-01

PDF · 533 SEK
Standard · ASTM ASTM D5911/D5911M

Standard Practice for Minimum Set of Data Elements to Identify a Soil Sampling Site

1.1 This practice covers what information should be obtained to uniquely identify any soil sampling or examination site where an absolute and recoverable location is necessary for quality control o...

Språk

Publicerad

2010-08-01

PDF · 533 SEK
Standard · ASTM ASTM D5970

Standard Practice for Deterioration of Geotextiles from Outdoor Exposure

1.1 This test method covers evaluating the deterioration in tensile strength and strain after outdoor exposure. 1.2 The deterioration is assessed as a reduction in strength and strain at failure ...

Språk

Publicerad

1996-05-10

Upphävd

2009-06-01

PDF · 468 SEK
Standard · ASTM ASTM D6031/D6031M

Standard Test Method for Logging In Situ Moisture Content and Density of Soil and Rock by the Nuclear Method in Horizontal, Slanted, and Vertical A...

1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 The in situ wa...

Språk

Publicerad

2010-08-01

PDF · 533 SEK
Standard · ASTM ASTM D6626

Standard Specification for Graded Trinidad Lake Modified Asphalt Binder

1.1 This specification covers graded Trinidad Lake modified asphalt binders. Grading designations are related to the average seven-day maximum pavement design temperature, oC, the intermediate pave...

Språk

Publicerad

2001-04-10

Upphävd

2009-06-15

PDF · 468 SEK
Standard · ASTM ASTM D6641/D6641M

Standard Test Method for Determining the Compressive Properties of Polymer Matrix Composite Laminates Using a Combined Loading Compression (CLC) Te...

1.1 This test method establishes a procedure for determining the compressive strength and stiffness properties of polymer matrix composite materials using a combined loading compression (CLC) (1) o...

Språk

Publicerad

2001-03-10

Upphävd

2009-04-15

PDF · 533 SEK
Standard · ASTM ASTM D6769/D6769M

Standard Guide for Application of Fully Adhered, Cold-Applied, Prefabricated Reinforced Modified Bituminous Membrane Waterproofing Systems

1.1 This guide lists application and installation requirements for fully adhered, cold-applied, prefabricated modified bituminous membrane waterproofing systems for below-grade or below-wearing-sur...

Språk

Publicerad

2010-06-01

PDF · 468 SEK
Standard · ASTM ASTM D6856/D6856M

Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials

1.1 This guide is applicable to the testing of textile composites fabricated using fabric preforms, such as weaves, braids, stitched preforms, and so forth, as the reinforcement. The purpose of t...

Språk

Publicerad

2008-09-01

PDF · 533 SEK
Standard · ASTM ASTM D6944

Standard Test Method for Resistance of Cured Coatings to Thermal Cycling

1.1 This test method determines the resistance of cured coatings to repeated thermal cycles. This procedure is designed to assess the influence of thermal cycling on adhesion and other properties o...

Språk

Publicerad

2003-07-10

Upphävd

2009-07-01

PDF · 468 SEK
Standard · ASTM ASTM D7038

Standard Test Method for Evaluation of Moisture Corrosion Resistance of Automotive Gear Lubricants

1.1 This test method covers a test procedure for evaluating the rust and corrosion inhibiting properties of a gear lubricant while subjected to water contamination and elevated temperature in a ben...

Språk

Publicerad

2008-10-15

Upphävd

2009-04-15

PDF · 767 SEK
Standard · ASTM ASTM D7377

Standard Practice for Evaluating the Water Wash-Off Resistance of Traffic Paints

1.1 A newly applied traffic paint film may be exposed to rain of varying intensities shortly after application. This practice was designed to determine the relative water wash-off resistance of an ...

Språk

Publicerad

2008-04-09

Upphävd

2009-06-01

PDF · 468 SEK
Standard · ASTM ASTM D7452

Standard Test Method for Evaluation of the Load Carrying Properties of Lubricants Used for Final Drive Axles, Under Conditions of High Speed and Sh...

1.1 This test method covers the determination of the anti-scoring properties of final drive axle lubricating oils when subjected to high-speed and shock conditions. This test method is commonly ref...

Språk

Publicerad

2008-05-01

Upphävd

2009-04-15

PDF · 767 SEK
Standard · ASTM ASTM E213

Standard Practice for Ultrasonic Examination of Metal Pipe and Tubing

1.1 This practice covers a procedure for detecting discontinuities in metal pipe and tubing during a volumetric examination using ultrasonic methods. Specific techniques of the ultrasonic method to...

Språk

Publicerad

2004-01-01

Upphävd

2009-06-01

PDF · 611 SEK
Standard · ASTM ASTM E463

Standard Test Method for Silica in Fluorspar by the Silico-Molybdate Visible Spectrometry

1.1 This test method covers the determination of silica in fluorspar in concentrations from 0.5 % to 10 %. 1.2 The values stated in SI units are to be regarded as standard. No other units of measur...

Språk

Publicerad

2008-12-15

Upphävd

2009-05-01

PDF · 468 SEK
Standard · ASTM ASTM E670

Standard Test Method for Side Force Friction on Paved Surfaces Using the Mu-Meter

1.1 This test method covers the measurement of the side force friction of paved surfaces utilizing a device commonly called a Mu-Meter. 1.2 This test method utilizes a measurement obtained by pul...

Språk

Publicerad

2000-01-01

Upphävd

2009-08-01

PDF · 611 SEK
Standard · ASTM ASTM E670

Standard Test Method for Side Force Friction on Paved Surfaces Using the Mu-Meter

1.1 This test method covers the measurement of the side force friction of paved surfaces utilizing a device commonly called a Mu-Meter. 1.2 This test method utilizes a measurement obtained by pul...

Språk

Publicerad

2009-08-01

PDF · 611 SEK
Standard · ASTM ASTM E722

Standard Practice for Characterizing Neutron Energy Fluence Spectra in Terms of an Equivalent Monoenergetic Neutron Fluence for Radiation-Hardness ...

1.1 This practice covers procedures for characterizing a neutron fluence from a source in terms of an equivalent monoenergetic neutron fluence. It is applicable to neutron effects testing, to the d...

Språk

Publicerad

2007-05-09

Upphävd

2009-06-01

PDF · 611 SEK
Standard · ASTM ASTM E722

Standard Practice for Characterizing Neutron Fluence Spectra in Terms of an Equivalent Monoenergetic Neutron Fluence for Radiation-Hardness Testing...

1.1 This practice covers procedures for characterizing neutron fluence from a source in terms of an equivalent monoenergetic neutron fluence. It is applicable to neutron effects testing, to the dev...

Språk

Publicerad

2009-06-01

PDF · 767 SEK
Standard · ASTM ASTM E1004

Standard Practice for Determining Electrical Conductivity Using the Electromagnetic (Eddy-Current) Method

1.1 This practice covers a procedure for determining the electrical conductivity of nonmagnetic metals using the electromagnetic (eddy-current) method. The procedure has been written primarily for ...

Språk

Publicerad

2002-07-10

Upphävd

2009-05-15

PDF · 468 SEK
Standard · ASTM ASTM E1158

Standard Guide for Material Selection and Fabrication of Reference Blocks for the Pulsed Longitudinal Wave Ultrasonic Examination of Metal and Meta...

1.1 This guide covers general procedures for the material selection and fabrication of reference blocks made of metal or metal alloys and intended to be used for the examination of the same or simi...

Språk

Publicerad

2004-02-01

Upphävd

2009-06-01

PDF · 533 SEK
Standard · ASTM ASTM E1161

Standard Test Method for Radiologic Examination of Semiconductors and Electronic Components

1.1 This test method provides a standard procedure for nondestructive radiographic examination of semiconductor devices, electronic components, and the materials used for construction of these item...

Språk

Publicerad

2003-06-10

Upphävd

2009-06-01

PDF · 468 SEK
Standard · ASTM ASTM E1453

Standard Guide for Storage of Media That Contains Analog or Digital Radioscopic Data

1.1 This guide may be used for the control and maintenance of recorded and unrecorded magnetic and optical media of analog or digital electronic data from industrial radioscopy.1.2 This standard do...

Språk

Publicerad

2002-12-10

Upphävd

2009-07-01

PDF · 468 SEK
Standard · ASTM ASTM E1751/E1751M

Standard Guide for Temperature Electromotive Force (emf) Tables for Non-Letter Designated Thermocouple Combinations

1.1 This guide consists of reference tables that give temperature-electromotive force (emf) relationships for special purpose, limited use, thermocouple combinations that do not have a letter desig...

Språk

Publicerad

2009-06-01

PDF · 1.027 SEK
Visa varukorgen Fortsätt handla 0
Varukorgen Stäng
Annonstext