21363 träffar på

Standard · ASTM ASTM F959M

Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use With Structural Fasteners [Metric]

1.1 This specification covers the requirements for compressible-washer-type direct tension indicators capable of indicating the achievement of a specified minimum bolt tension in a structural bolt....

Språk

Publicerad

2006-11-01

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM F1267

Standard Specification for Metal, Expanded, Steel

1.1 This specification covers expanded metal.1.1.1 Expanded metal covered by this specification is intended for a variety of applications.1.2 The values stated in inch-pound units are to be regarde...

Språk

Publicerad

2007-01-11

Upphävd

2007-11-01

PDF · 533 SEK

Standard · ASTM ASTM F1852

Standard Specification for "Twist Off" Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 120/105 ksi Minimum Tensile...

1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as "sets". These assemblies are capable of developing a minimum predeter...

Språk

Publicerad

2005-01-01

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM C242

Standard Terminology of Ceramic Whitewares and Related Products

1.1 This terminology pertains to the terminology used in ceramic whitewares and related products. 1.2 Words adequately defined in standard dictionaries are not included. Included are words that a...

Språk

Publicerad

2001-07-10

Upphävd

2007-11-01

PDF · 533 SEK

Standard · ASTM ASTM C916

Standard Specification for Adhesives for Duct Thermal Insulation

1.1 This specification covers minimum material requirements, and safety precautions in application, for adhesives to bond thermal insulation duct liner on the interior surfaces of sheet metal air c...

Språk

Publicerad

1985-07-26

Upphävd

2007-11-01

PDF · 468 SEK

Standard · ASTM ASTM C916

Standard Specification for Adhesives for Duct Thermal Insulation

Språk

Publicerad

2008-02-06

PDF · 468 SEK

Standard · ASTM ASTM C1134

Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion

1.1 This test method determines the amount of water retained (including surface water) by rigid block and board thermal insulations used in building construction applications after these materials ...

Språk

Publicerad

2001-01-01

Upphävd

2007-11-01

PDF · 533 SEK

Standard · ASTM ASTM C1134

Standard Test Method for Water Retention of Rigid Thermal Insulations Following Partial Immersion

Språk

Publicerad

2008-02-06

PDF · 533 SEK

Standard · ASTM ASTM D933

Standard Practice for Reporting Results of Examination and Analysis of Water-Formed Deposits

1.1 This practice covers the manner in which the results of examination and analysis for inorganic constituents of deposits formed from waters are to be reported.1.2 While various practices of repo...

Språk

Publicerad

1984-09-11

Upphävd

2007-12-01

PDF · 468 SEK

Standard · ASTM ASTM D1073

Standard Specification for Fine Aggregate for Bituminous Paving Mixtures

1.1 This specification covers fine aggregate for use in bituminous paving mixtures.1.2 This specification is intended to describe material from a single source. When material from two or more sourc...

Språk

Publicerad

2006-06-01

Upphävd

2007-12-01

PDF · 468 SEK

Standard · ASTM ASTM D1245

Standard Practice for Examination of Water-Formed Deposits by Chemical Microscopy

1.1 This practice describes a procedure for the examination of water-formed deposits by means of chemical microscopy. This practice may be used to complement other methods of examination of water-f...

Språk

Publicerad

1984-10-26

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM D2171

Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

Språk

Publicerad

2001-11-01

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM D2171

Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

1.1 This test method covers procedures for the determination of viscosity of asphalt binder (bitumen) by vacuum capillary viscometers at 60°C (140°F). It is applicable to mate...

Språk

Publicerad

2008-02-06

PDF · 533 SEK

Standard · ASTM ASTM D3375

Standard Test Method for Column Capacity of Particulate Mixed Bed Ion Exchange Materials

1.1 This test method covers the determination of the performance of particulate mixed bed ion exchange materials in the regenerated form when used for deionization. It is intended for use in testin...

Språk

Publicerad

1995-01-10

Upphävd

2007-12-01

PDF · 468 SEK

Standard · ASTM ASTM D3375

Standard Test Method for Column Capacity of Particulate Mixed Bed Ion Exchange Materials

Språk

Publicerad

2008-02-06

PDF · 468 SEK

Standard · ASTM ASTM D3542

Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Bridges

1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and...

Språk

Publicerad

1992-11-15

Upphävd

2007-12-01

PDF · 468 SEK

Standard · ASTM ASTM D3963/D3963M

Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars

1.1 This specification covers the fabrication and jobsite requirements for deformed and plain steel reinforcing bars with protective epoxy coating applied in accordance with Specification A775. 1....

Språk

Publicerad

2001-01-10

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM D3963/D3963M

Standard Specification for Fabrication and Jobsite Handling of Epoxy-Coated Steel Reinforcing Bars

1.1 This specification covers the fabrication and jobsite requirements for deformed and plain steel reinforcing bars with protective epoxy coating applied in accordance with Specification A 775/A ...

Språk

Publicerad

2008-02-06

PDF · 533 SEK

Standard · ASTM ASTM D4638

Standard Guide for Preparation of Biological Samples for Inorganic Chemical Analysis

1.1 This guide describes procedures for the preparation of test samples collected from such locations as streams, rivers, ponds, lakes, estuaries, oceans, and toxicity tests and is applicable to su...

Språk

Publicerad

2003-12-01

Upphävd

2007-12-01

PDF · 533 SEK

Standard · ASTM ASTM D5131

Standard Guide for Record Keeping for Electrodialysis/Electrodialysis Reversal Systems

1.1 This guide covers procedures for well defined record keeping for electrodialysis (ED) and electrodialysis reversal (EDR) systems. 1.2 This guide includes a start up report and record keeping f...

Språk

Publicerad

2001-01-01

Upphävd

2007-12-01

PDF · 468 SEK

Standard · ASTM ASTM D5131

Standard Guide for Record Keeping for Electrodialysis/Electrodialysis Reversal Systems

1.1 This guide covers procedures for well defined record keeping for electrodialysis (ED) and electrodialysis reversal (EDR) systems. 1.2 This guide includes a start up report and record keeping f...

Språk

Publicerad

2008-02-06

PDF · 468 SEK

Standard · ASTM ASTM B108

Standard Specification for Aluminum-Alloy Permanent Mold Castings

1.1 This specification covers aluminum-alloy permanent mold castings designated as shown in .1.2 This specification is not intended for aluminum-alloy permanent mold castings used in aerospace appl...

Språk

Publicerad

2006-11-01

Upphävd

2008-06-01

PDF · 611 SEK

Standard · ASTM ASTM B618

Standard Specification for Aluminum-Alloy Investment Castings

1.1 This specification covers aluminum-alloy investment castings designated as shown in Table 1.1.2 This specification is not intended for aluminum-alloy investment castings used in aerospace appli...

Språk

Publicerad

2006-09-01

Upphävd

2007-10-01

PDF · 533 SEK

Standard · ASTM ASTM B618/B618M

Standard Specification for Aluminum-Alloy Investment Castings

Språk

Publicerad

2007-12-05

Upphävd

2008-06-01

PDF · 611 SEK

Standard · ASTM ASTM B955/B955M

Standard Specification for Aluminum-Alloy Centrifugal Castings

1.1 This specification covers aluminum-alloy centrifugal castings designated as shown in Table 1.1.2 This specification is not intended for aluminum-alloy centrifugal castings used in aerospace app...

Språk

Publicerad

2008-01-09

Upphävd

2008-07-15

PDF · 533 SEK

Standard · ASTM ASTM B221

Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

1.1 This specification covers aluminum and aluminum-alloy extruded bar, rod, wire, profile, and tube in the aluminum alloys (Note 0) and tempers shown in . Note 0Throughout this specification, the ...

Språk

Publicerad

2006-11-01

Upphävd

2008-08-08

PDF · 611 SEK

Standard · ASTM ASTM B265

Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate

1.1 This specification covers annealed titanium and titanium alloy strip, sheet, and plate as follows: 1.1.1 Grade 1—Unalloyed titanium, 1.1.2 Grade 2—Una...

Språk

Publicerad

2008-02-06

Upphävd

2008-08-01

PDF · 533 SEK

Standard · ASTM ASTM B338

Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers

1.1 This specification covers the requirements for 28 grades of titanium and titanium alloy tubing intended for surface condensers, evaporators, and heat exchangers, as follows:1.1.1 Grade 1 Una...

Språk

Publicerad

2006-06-01

Upphävd

2008-08-01

PDF · 533 SEK

Standard · ASTM ASTM B348

Standard Specification for Titanium and Titanium Alloy Bars and Billets

Språk

Publicerad

2006-01-01

Upphävd

2008-08-01

PDF · 533 SEK

Standard · ASTM ASTM A612/A612M

Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service

Språk

Publicerad

2003-09-10

Upphävd

2007-11-01

PDF · 468 SEK

Förfina din sökning genom att visa:

...som handlar om: