1.1 This test method describes the spectrophotometric determination of total aldehyde carbonyl content in the range of 0.5 to 50 mg/kg (as acetaldehyde) or 0.3 to 35 mg/kg (as formaldehyde) in mono...
2008-08-06
1.1 This test method covers a relative measure of the plastic behavior of coal when heated under prescribed conditions. This test method may be used to obtain semiquantitative values of the plastic...
2008-05-15
1.1 This specification covers the general requirements for hot-rolled steel strip in coils and cut lengths. It applies to carbon steel and high-strength, low-alloy steel furnished as hot-rolled. 1...
2002-11-10
1.1 This test method establishes procedures for evaluating protective coating systems test specimens under simulated DBA conditions. Included are a description of conditions and apparatus for t...
2008-11-01
1.1 This test method describes the gas chromatographic determination of purity for 1,3-propanediol (PDO). This test method was originally developed to determine the purity of 1,3-propanediol used f...
2009-04-01
1.1 This specification covers stainless steel clamps for use with four sizes of insert fittings that comply with F 1807, and cross-linked polyethylene (PEX) plastic tubing that complies with F 876 ...
2008-05-14
1.1 This practice covers methods of reporting and recording visual observations of oil on water and related response activities. 1.2 This practice applies only to visual observations of oil on wate...
2008-12-03
1.1 This guide provides recommendations for reporting the results of property values for plastics and thermoplastic elastomers in published literature, data sheets, presentations, comparative analy...
2008-11-05
1.1 This practice covers the installation of suspension systems for acoustical tile and lay-in panels. It is applicable to contractors whose services are utilized for installing acoustical ceilings...
1.1 This test method covers the determination of the amount of total solids remaining after drying a sample. Materials suitable for this procedure include samples prepared in accordance with Practi...
2008-06-04
1.1 This practice covers procedures for the dynamic verification of cyclic force amplitude control or measurement accuracy during constant amplitude testing in an axial fatigue testing system. It i...
1.1 These test methods cover the determination of a flow rate, by use of the Carney funnel, of metal powders and powder mixtures that do not readily flow through the Hall funnel of Test Method B 21...
1.1 This practice covers the calculation of supersaturation of barium sulfate, strontium sulfate, and calcium sulfate dihydrate (gypsum) in brackish water, seawater, and brines in which barium, st...
1.1 This test method covers the determination of dissolved and total recoverable elements in water, which includes drinking water, lake water, river water, sea water, snow, and Type II reagent wate...
2008-10-01
1.1 This practice establishes the physical item marking requirements for identification purposes for aluminum and magnesium products. Package marking for shipment and inspection acceptance is not w...
2008-10-08
1.1 This specification covers two grades of zirconium metal commonly designated as sponge or chunklets, but may also take other forms. This specification does not include crystal bar zi...
1.1 This standard provides a method for evaluating the ability of an architectural paint system to block ink stains from markers and writing instruments from bleeding through a primer into a topcoa...
2009-02-01
1.1 This practice covers the inspection of underground precast concrete utility structures designed and manufactured in accordance with Practice C 857 and Specification C 858. 1 This practice cover...
2008-09-03
1.1 This guide provides time-of-flight secondary ion mass spectrometry (ToF-SIMS) users with a method for forms of interpretation of mass spectral data. This guide is applicable to most ToF-SIMS in...
2009-05-01
1.1 This test method covers a laboratory procedure for determining the ability of a waterproofing membrane to bridge a crack in the substrate. 1.2 There are no ISO standards similar or equivalent ...
2008-12-15
1.1 This specification covers only factory-made wrought aluminum and aluminum-alloy welding fittings in contrast to field-made fittings. The term “welding fittings” app This s...
1.1 This specification establishes the requirements for annealed copper-alloy strip for the manufacture of flexible metal hose produced from Copper Alloy UNS Nos. C41100 and C50500. 1.1.1 The nomin...
1.1 This specification establishes the requirements for copper-beryllium alloy plate, sheet, strip, and rolled bar. The following alloys are specified: This specification establishes the requirem...
1.1 This test method describes the measurement of the net heat flux normal to a surface using gages inserted flush with the surface. The geometry is the same as heat-flux gages covered by Test Meth...
2009-06-15
1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths. 1.2 Units
1.1 This guide will improve and advance computer forensics through the development of model curricula consistent with other forensic science programs. 1.2 Section 4 describes the alternative paths ...
1.1 This test method covers a procedure for the determination of the transmittance of monoethylene glycol (1,2-ethanediol; MEG) at wavelengths in the region 220 to 350 nm. The results provide a mea...
1.1 This test method covers the preparation, equipment, test procedure, and data reduction for determining in situ modulus of deformation of a rock mass using the flexible plate loading method. 1.2...
1.1 This test method describes a laboratory procedure for determining the resistance of a waterproofing membrane to hydrostatic pressure. 1.2 The committee with jurisdiction over this standard is ...
1.1 This test method covers the determination of the total nitrogen content of water in concentrations from 0.5 to 1000 mg/L. Higher nitrogen concentrations may be determined by making the proper d...
2008-05-01