21336 träffar på

ASTM F901
Standard · ASTM ASTM F901

Standard Specification for Aluminum Transmission Tower Bolts and Nuts

1.1 This specification covers aluminum structural bolts and nuts for use in the construction of aluminum transmission towers, substations, and similar aluminum structures. 1.2 Diameters of bolts ...

Språk

Publicerad

2007-09-05
PDF · 468 SEK
ASTM E2147
Standard · ASTM ASTM E2147

Standard Specification for Audit and Disclosure Logs for Use in Health Information Systems

1.1 This specification is for the development and implementation of security audit/disclosure logs for health information. It specifies how to design an access audit log to record This s...

Språk

Publicerad

2001-11-10
PDF · 533 SEK
ASTM G99
Standard · ASTM ASTM G99

Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

1.1 This test method covers a laboratory procedure for determining the wear of materials during sliding using a pin-on-disk apparatus. Materials are tested in pairs under nominally non-abrasive co...

Språk

Publicerad

2005-05-01
PDF · 533 SEK
ASTM D7272
Standard · ASTM ASTM D7272

Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods

1.1 This test method describes destructive quality control and/or quality assurance tests to determine the integrity of seams produced using taped seaming methods. This test method presents the pro...

Språk

Publicerad

2006-07-01
PDF · 533 SEK
ASTM D5165
Standard · ASTM ASTM D5165

Standard Practice for Laboratory Preparation of Gelled Vehicles Using a Resin Kettle (Withdrawn 2010)

1.1 This practice covers a laboratory procedure for the gelation of a resin solution, ink varnish, or vehicle using a resin kettle.1.2 Guidance in preparing gelled vehicle samples suitable for use ...

Språk

Publicerad

2004-11-01

Upphävd

2010-06-01
PDF · 468 SEK
ASTM E1074
Standard · ASTM ASTM E1074

Standard Practice for Measuring Net Benefits and Net Savings for Investments in Buildings and Building Systems

1.1 This practice covers a recommended procedure for calculating and interpreting the net benefits (NB) and net savings (NS) methods in the evaluation of building designs and systems. 1.2 The va...

Språk

Publicerad

2009-04-01
PDF · 533 SEK
ASTM F1172
Standard · ASTM ASTM F1172

Standard Specification for Fuel Oil Meters of the Volumetric Positive Displacement Type

1.1 This specification provides the minimum requirements for the design, fabrication, pressure rating, marking, and testing for fuel oil meters (volumetric positive displacement type). 1.2 The valu...

Språk

Publicerad

2010-03-01
PDF · 468 SEK
ASTM F1931
Standard · ASTM ASTM F1931

Standard Test Method for Characterization of Gymnastic Landing Mats and Floor Exercise Surfaces (Withdrawn 2011)

1.1 This test method covers the measurement of shock absorption characteristics and rebound properties of landing mats and floor exercise surfaces used in the sport of gymnastics. It defines quanti...

Språk

Publicerad

2004-05-01

Upphävd

2011-04-08
PDF · 468 SEK
ASTM E1668
Standard · ASTM ASTM E1668

Standard Classification for Serviceability of an Office Facility for Amenities to Attract and Retain Staff

1.1 This classification covers pairs of scales for classifying an aspect of the serviceability of an office facility, that is, the capability of an office facility to meet certain possible requirem...

Språk

Publicerad

2005-05-01
PDF · 533 SEK
ASTM F1097
Standard · ASTM ASTM F1097

Standard Specification for Mortar, Refractory (High-Temperature, Air-Setting)

1.1 This specification covers dry air-setting refractory mortar for use in laying and bonding refractory brick in ship boiler furnaces and wet air-setting refractory mortar for use in laying refrac...

Språk

Publicerad

2007-02-07
PDF · 468 SEK
ASTM B564
Standard · ASTM ASTM B564

Standard Specification for Nickel Alloy Forgings

1.1 This specification covers forgings of nickel alloy UNS N02200, Ni-Cu alloy UNS N04400, Ni-Cr-Fe alloys UNS N06600, UNS N06603, and UNS N06690, Ni-Cr-Mo-Nb alloy UNS N06625, Ni-Cr-Mo-Si alloy ...

Språk

Publicerad

2011-12-16
PDF · 611 SEK
ASTM D3741
Standard · ASTM ASTM D3741

Standard Test Methods for Appearance of Admixtures Containing Halogenated Organic Solvents

1.1 These test methods cover the visual determination of the physical appearance of admixtures containing halogenated hydrocarbons. These test methods are qualitative test methods. 1.2 This standard d

Språk

Publicerad

2000-01-10
PDF · 468 SEK
ASTM D2959
Standard · ASTM ASTM D2959

Standard Test Method for Ethylene Oxide Content of Polyethoxylated Nonionic Surfactants

1.1 This test method covers the determination of ethylene oxide in polyethoxylated nonionic surfactants. It can also be used for compounds containing propylene oxide or any compounds (glycols and g...

Språk

Publicerad

2009-10-01
PDF · 468 SEK
ASTM B657
Standard · ASTM ASTM B657

Guide for Metallographic Identification of Microstructure in Cemented Carbides

1.1 This test method covers apparatus and procedures for the metallographic determination of microstructures in cemented tungsten carbides. 1.2 This standard does not purport to address all of t...

Språk

Publicerad

2012-02-24
PDF · 533 SEK
ASTM B858
Standard · ASTM ASTM B858

Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys

1.1 This test method describes a procedure to determine the presence of residual stresses in wrought copper alloy products that may lead to stress corrosion cracking. An ammonia vapor atmosphere is...

Språk

Publicerad

2006-03-15
PDF · 468 SEK
ASTM D2803
Standard · ASTM ASTM D2803

Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal

1.1 This guide covers three procedures for determining the susceptibility of organic-coated metal substrates to formation of filiform corrosion. 1.2 This guide is limited to the determination of ...

Språk

Publicerad

2009-08-01
PDF · 468 SEK
ASTM D6951/D6951M
Standard · ASTM ASTM D6951/D6951M

Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications

1.1 This test method covers the measurement of the penetration rate of the Dynamic Cone Penetrometer with an 8-kg [17.6-lb] hammer (8-kg [17.6-lb] DCP) through undisturbed soil or compacted materia...

Språk

Publicerad

2009-11-01
PDF · 533 SEK
ASTM D806
Standard · ASTM ASTM D806

Standard Test Method for Cement Content of Hardened Soil-Cement Mixtures

1.1 This test method covers the determination by chemical analysis of cement content of hardened soil-cement mixtures.1.2 All observed and calculated values shall conform to the guidelines for sign...

Språk

Publicerad

2012-02-24
PDF · 468 SEK
ASTM D1754/D1754M
Standard · ASTM ASTM D1754/D1754M

Standard Test Method for Effect of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)

1.1 This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected a...

Språk

Publicerad

2009-07-01
PDF · 533 SEK
ASTM E1636
Standard · ASTM ASTM E1636

Standard Practice for Analytically Describing Depth-Profile and Linescan-Profile Data by an Extended Logistic Function

1.1 This practice describes a systematic method for analyzing depth-profile and linescan data and for accurately characterizing the shape of an interface region or topographic feature. The profi...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM C1511
Standard · ASTM ASTM C1511

Standard Test Method for Determining the Water Retention (Repellency) Characteristics of Glass Fiber Insulation (Aircraft Type)

1.1 This test method covers a laboratory procedure for evaluating the water absorption potential of blanket insulation for aircraft, thereby providing a measure of potential weight increase due to ...

Språk

Publicerad

2004-09-01
PDF · 468 SEK
ASTM D2234/D2234M
Standard · ASTM ASTM D2234/D2234M

Standard Practice for Collection of a Gross Sample of Coal

1.1 This practice covers procedures for the collection of a sample under various conditions of sampling. The sample is to be crushed and further prepared for analysis in accordance with Practice &l...

Språk

Publicerad

2010-01-01
PDF · 533 SEK
ASTM D3271
Standard · ASTM ASTM D3271

Standard Practice for Direct Injection of Solvent-Reducible Paints Into a Gas Chromatograph for Solvent Analysis

1.1 This practice describes the techniques used to inject whole paint samples directly into a gas chromatograph to obtain a chromatogram from which the solvent composition may be e

Språk

Publicerad

2006-06-01
PDF · 468 SEK
ASTM A705/A705M
Standard · ASTM ASTM A705/A705M

Standard Specification for Age-Hardening Stainless Steel Forgings

1.1 This specification covers age-hardening stainless steel forgings for general use. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The v...

Språk

Publicerad

2004-01-01
PDF · 533 SEK
ASTM D1460
Standard · ASTM ASTM D1460

Standard Test Method for Rubber Property—Change in Length During Liquid Immersion

1.1 This test method covers a technique to measure the effect of immersion liquids on rubber vulcanizates or rubbery materials. Change in specimen geometry and dimensions are observed through the ...

Språk

Publicerad

2010-01-01
PDF · 468 SEK
ASTM E921
Standard · ASTM ASTM E921

Standard Specification for Export Packaged Laboratory Apparatus

1.1 This specification covers the procedures for testing loaded shipping containers. Drop, vibration and compression tests are performed to measure the ability of the shipping container to protect ...

Språk

Publicerad

1997-11-10
PDF · 468 SEK
ASTM D3003
Standard · ASTM ASTM D3003

Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates

1.1 This test method covers determination of the pressure mottling and sticking, or blocking resistance of organic coatings applied to coil-coated or factory-coated metal prior to fabric This test ...

Språk

Publicerad

2006-07-01
PDF · 468 SEK
ASTM D7205/D7205M
Standard · ASTM ASTM D7205/D7205M

Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars

1.1 This test method determines the quasi-static longitudinal tensile strength and elongation properties of fiber reinforced polymer matrix (FRP) composite bars commonly used as tensile elements in...

Språk

Publicerad

2006-03-15
PDF · 611 SEK
ASTM D3437
Standard · ASTM ASTM D3437

Standard Practice for Sampling and Handling Liquid Cyclic Products

1.1 This practice covers procedures for sampling and handling several liquid cyclic products. These specifically cover liquids at ambient temperature and include benzene, toluene, xylenes...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM B664
Standard · ASTM ASTM B664

Standard Specification for 80 % Silver-20 % Graphite Sliding Contact Material

1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 80 %, by weight, with the balance being substantially graphite. ...

Språk

Publicerad

2006-06-01
PDF · 468 SEK
Förfina din sökning genom att visa:
...som handlar om:

Ämnesområden (0)

Avbryt

Branscher (0)

Avbryt

Syfte (0)

Avbryt

Material (0)

Avbryt
Visa varukorgen Fortsätt handla 0
Varukorgen Stäng
Annonstext