1.1 This practice covers the evaluation of atmospheric galvanic corrosion of any anodic material that can be made into a wire when in contact with a cathodic material that can be made into a threa...
2004-11-01
1.1 This test method covers the observation of the temperatures at which triangular pyramids (cones) prepared from coal and coke ash attain and pass through certain defined stages of fusing and fl...
2010-09-01
1.1 The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can wit The s...
2005-04-01
1.1 This test method covers the materials and methods for the static and dynamic testing of intervertebral body fusion device assemblies, spinal implants designed to promote arthrodesis at a given ...
2011-09-16
1.1 This test method describes procedures to establish the relative bond strength of 0.600-in. [15.24-mm] diameter, Grade 270 [1860] steel prestressing strand in cement grout as used in prestressed...
1.1 This test method covers a laboratory procedure for the determination of the degree of slump of a sealant when used in a vertical joint in a structure. 1.2 The values stated in either inch-pound...
2006-05-01
1.1 This test method covers the on-line determination of soluble silica in water by colorimetric analysis using the molybdenum blue method, also known as the heteropoly blue method. 1.2 This test...
2011-05-20
1.1 This test method is used to evaluate the repellency of promising compounds that have undergone primary laboratory studies and have been approved for skin application for secondary testing. 1.2...
2006-04-01
1.1 This test method covers the determination of dissolved elements in ground water, surface water, and drinking water. It may also be used for the determination of total-recoverable elements in th...
2010-10-15
1.1 These digital reference images illustrate the types and degrees of discontinuities that may be found in aluminum-alloy castings. The castings illustrated are in thicknesses of 1/ 4 in. [6.35 mm...
2012-02-24
1.1 This test method describes the requirements for sample preparation, tensile testing, and results calculation of flat fiber reinforced polymer (FRP) composite materials used for the strengthenin...
2010-05-17
1.1 This test method covers measurement techniques for calorimetrically determining the ratio of solar absorptance to hemispherical emittance using a steady-state method, and for calorimetrically d...
1.1 This specification covers the requirements for fabricated alumina parts suitable for electronic and electrical applications and ceramic-to-metal seals as used in electron devices. This standard...
2007-09-05
1.1 This test method covers the measurement of the thermal resistance, under steady-state conditions, of battings and batting/fabric systems, and other materials within the limits specified in 1...
1.1 This practice describes a specific procedure for using a bar code verifier to measure and quantify the optical and symbology characteristics relative to the print quality of a bar code symbol a...
2009-10-01
1.1 This practice consists of three annexes: hull structure, outfitting, and coating. The subject of these annexes was selected for several reasons. Other commercial shipbuilding nations already ha...
1.1 This test method covers the quantitative measurement and normalization of impact forces generated through a mechanical impact test on an athletic surface. The impact forces simulated in this te...
2012-03-23
1.1 This specification2 covers minimum-wall-thickness, electric-resistance-welded tubes made This specification covers standards for electric-resistance-welded tubes with minimum-wall-th...
2008-03-12
1.1 This test method covers a quantitative procedure to determine the cleanliness of PM bearings and structural parts. 1.2 This is a laboratory test consisting ...
2009-11-01
1.1 This test method covers the determination of the uniformity of gloss or sheen of a paint applied by brush to a test panel simulating an interior wall section. Variations in gloss or sheen that...
2005-05-15
1.1 This specification covers grades of hot-formed welded and seamless high-strength low-alloy square, rectangular, round, or special shape structural tubing for welded, riveted, or bolted construc...
2004-01-01
1.1 This test method covers the measurement of soluble, suspended, and total radium-226 in water in concentrations above 3.7 × 10−3 Bq/L. This test method is
2011-12-16
1.1 This test method covers the determination of the resistance of hardened concrete to penetration by either a steel probe or pin. 1.2 The values stated in either SI units or inch-pound units ...
2003-01-10
1.1 This practice is intended as a guide for the use of a flame photometric detector (FPD) as the detection component of a gas chromatographic system. This practice is intended as a guide for the u...
2005-09-01
1.1 These test methods cover the determination of manganese in iron ores, concentrates, and agglomerates. The following two test methods are included:
2011-03-18
1.1 1.1 This test method covers a rapid and quantitative determination of the residue in emulsified asphalts using a moisture analyzer. It is applicable to all nonsolvent-containing emulsion types....
1.1 This performance specification covers requirements for fillings for industry products such as wearing apparel, sleeping bags, and comforters containing down, feathers, down and feather blends, ...
2004-03-01
1.1 This specification covers welded UNS N08020 alloy boiler, heat exchanger, and condenser tubes for general corrosion-resisting and low- or high-temperature service. 1.2 This specification c...
1.1 This test method covers the determination of water in volatile solvents and chemical intermediates used in paint, varnish, lacquer, and related products. <div class="
1.1 This practice describes the procedure for sampling liquids with the composite liquid waste sampler, or “COLIWASA.” The COLIWASA is an appropriate device for obtain
2007-12-05