1.1 This practice covers the requirements for a 1.707-m [67.23-in.] diameter laboratory roadwheel for durability and endurance testing of tires under controlled operating and environmental conditi...
2009-11-01
1.1 These test methods cover the effective crimping on outside crimped valves within the wide parameters of containers and valves available. 1.2 The test methods appear in the following order:<...
2005-10-01
1.1 This specification covers the material, dimensions, and construction of diesel exhaust water traps, which shall be required whenever the exhaust is to be expelled through the hull of the vessel...
2004-11-01
1.1 This test method is based on existing Test Method D 3359, with modifications to make it suitable for plastic substrates and membrane switches. 1.2 Despite the problems associated with a tape test
2009-06-15
1.1 This specification provides standard dimensions for manual (lever and gear actuator) butterfly valves installed in shipboard piping systems in NPS 2 to NPS 24, inclusive. 1.2 This specification...
2010-03-01
1.1 These test methods cover chemical and physical tests applicable to linear detergent alkylates, evaluating those properties which characterize linear detergent alkylates with respect to its sui...
2009-10-01
1.1 This practice covers the procedure for static calibration of electronic transducer-based systems used to measure fluid pressures in laboratory or in field applications associated with geotechn...
1995-04-15
1.1 This test method covers primarily the determination of ignition loss of glass fiber textiles. This method applies to glass fiber strands, twisted or untwisted, coated or uncoated; and fabrics, ...
2011-05-20
D1.1 This specification covers two grades of molybdenum wire less than 0.050 in. (1.27 mm) in diameter and one grade of molybdenum rod 1.00 in. (25.4 mm) or less in diameter as follows: 1.1.1 This ...
1996-01-01
1.1 This practice covers a standardized terminology and some basic concepts for testing and sampling across the broad range of chemical and physical testing operations characteristic of the rubber ...
2006-10-01
1.1 This specification covers minimum requirements for a quality assurance program for lighter-than-air light sport aircraft. 1.2 This standard does not purport to address all of the safety concern...
2008-05-15
1.1 This practice covers the applications of methods for the extraction and gas chromatographic determination of organic vapors that have been adsorbed from air in sampling tubes packed with activa...
2007-12-05
1.1 This test method covers the determination of the composition of a materials stream in a solid waste resource recovery processing facility. The composition is determined with respect to one or m...
2009-09-01
1.1 This specification covers solid, unreinforced masonry units manufactured from autoclaved aerated concrete (AAC), a cementitious product. This specification addresses dimensional tolerances, ma...
2012-02-24
1.1 This practice describes a method for obtaining constant relative humidity ranging from 30 to 98 % at temperatures ranging from 0 to 70°C in relatively small containers by means of an...
2011-10-14
1.1 This terminology document is a compilation of definitions of terms, abbreviations, and acronyms that are unique to climbing, mountaineering, search and rescue collected in order to provide cons...
1.1 This test method covers the determination of free cyanides in waters and wastewaters. Free cyanide is here defined as the cyanide which diffuses as cyanide (HCN), at room temperature, from a so...
2002-07-10
1.1 These test methods describe mechanical tests for determining the following performance properties: 1.1.1 Compression Load, 1.1.2 Bending Load, 1.1.3 Impact Resistance, and <p
2011-09-16
1.1 This guide covers artist's papers used in the preparation of permanent or semipermanent artwork. Some works of art are expected to last several hundred years, and others might be expected to la...
2007-01-11
2010-08-15
1.1 This test method covers a general procedure for determining the thermal conductivity of whiteware ceramics over the temperature range from 100 to 300°F (40 to 150°
2006-02-15
1.1 This test method covers an accelerated procedure for evaluating the print resistance of architectural paints. It differs from print resistance Test Method <
2008-02-01
1.1 This test method covers the determination of soluble lithium, potassium, and sodium ions in brackish water, seawater, and brines by atomic absorption spectrophotometry. 1.2 Samples containing ...
1.1 This specification covers four different grades of round and shaped plain carbon and alloy steel spring wire, uniform in quality and temper, intended for the manufacture of mechanical springs t...
1.1 This standard describes a test method for evaluating the ignition sensitivity and fault tolerance of oxygen regulators used for medical and emergency applications. 1.2 For the purpose of this s...
2003-04-10
1.1 This practice covers acoustic emission (AE) examination or monitoring of fiberglass-reinforced plastic (FRP) tanks-vessels (equipment) under pressure or vacuum to determine structural integrity...
1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelop...
2009-05-15
1.1 This test method covers the determination of the operating characteristics of continuous electrodeionization (CEDI) devices, indicative of deionization performance when a device is applied to p...
2002-06-10
1.1 This test method covers the determination of puncture properties of plastic films, over a range of test velocities. 1.1.1 Test Method <a href="http://myastm.astm.org/SUBSCRIPTION/NewValidate...
2010-06-18
1.1 This specification provides general requirements for styrene-rubber solvent cements to be used in joining styrene-rubber (SR) plastic pipe and fittings. 1.2 A recommended procedure for joining...
1995-09-10
1.1 This test method covers accelerated procedures for simultaneously determining comparative characteristics of coating systems applied to steep pipe exterior for the purpose of preventing or miti...
1998-05-10
2007-03-21