21320 träffar på

ASTM F1595
Standard · ASTM ASTM F1595

Standard Practice for Viewing Conditions for Visual Inspection of Membrane Switches

1.1 This practice covers procedures for performing visual inspection of membrane switches. This includes visual inspection of overlays and circuitry. 1.2 This practice defines lighting parameters,...

Språk

Publicerad

2005-05-01
PDF · 468 SEK
ASTM C424
Standard · ASTM ASTM C424

Standard Test Method for Crazing Resistance of Fired Glazed Whitewares by Autoclave Treatment

1.1 This test method covers the determination of the crazing resistance of fired glazed whitewares using the autoclave treatment and under the conditions specified in this test method. 1.2 The valu...

Språk

Publicerad

2006-02-15
PDF · 468 SEK
ASTM F79
Standard · ASTM ASTM F79

Standard Specification for Type 101 Sealing Glass

1.1 This specification covers Type 101 sealing glass for use in electronic applications. Note 1—This specification is primarily intended to consider glass as most generally This specifi...

Språk

Publicerad

2005-09-01
PDF · 468 SEK
ASTM D1349
Standard · ASTM ASTM D1349

Standard Practice for Rubber-Standard Temperatures for Testing

1.1 This practice covers a list of standard temperatures from which selection may be made for any specific test or test method. Any standard, method, practice, procedure, or specification that spec...

Språk

Publicerad

2009-07-01
PDF · 468 SEK
ASTM D7332/D7332M
Standard · ASTM ASTM D7332/D7332M

Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite

1.1 This test method determines the fastener pull-through resistance of multidirectional polymer matrix composites reinforced by high-modulus fibers. Fastener pull-through resistance is characteriz...

Språk

Publicerad

2009-09-01
PDF · 611 SEK
ASTM F659
Standard · ASTM ASTM F659

Standard Specification for Ski and Snowboard Goggles

1.1 This specification covers the minimal requirements of ski and snowboard goggles (intended for nonmotorized use) to provide a reasonable degree of protection against snow and moisture striking o...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM C664
Standard · ASTM ASTM C664

Standard Test Methods for Thickness of Diffusion Coating

1.1 These test methods cover two procedures for measuring the thickness of diffusion coatings. 1.2 Test Method A is the determination of the dimensional-change thickness, defined as the difference ...

Språk

Publicerad

2010-06-18
PDF · 468 SEK
ASTM E640
Standard · ASTM ASTM E640

Standard Test Method for Preservatives in Water-Containing Cosmetics

1.1 This test method covers the determination of the suitability of preservatives for use in cosmetic formulations. It sets minimal requirements for preservative performance in model formulations. ...

Språk

Publicerad

2006-11-15
PDF · 468 SEK
ASTM D3222
Standard · ASTM ASTM D3222

Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

1.1 This specification covers melt processable molding and extrusion materials, as well as coating materials of poly(vinylidene fluoride) fluoroplastic, commonly abbreviated PVDF (or PVF2 in scient...

Språk

Publicerad

2005-07-01
PDF · 533 SEK
ASTM D3005
Standard · ASTM ASTM D3005

Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

1.1 This specification covers an electrical insulating tape for use at low temperature down to approximately −18 °C (0 °F). The tape This specification covers the p...

Språk

Publicerad

2010-08-20
PDF · 468 SEK
ASTM G95
Standard · ASTM ASTM G95

Standard Test Method for Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method) (Withdrawn 2007)

1.1 This test method covers accelerated procedures for simultaneously determining comparative characteristics of coating systems applied to steep pipe exterior for the purpose of preventing or miti...

Språk

Publicerad

1998-05-10

Upphävd

2007-03-21
PDF · 468 SEK
ASTM D430
Standard · ASTM ASTM D430

Standard Test Methods for Rubber Deterioration—Dynamic Fatigue

1.1 These test methods cover testing procedures that estimate the ability of soft rubber materials to resist dynamic fatigue. No exact correlation between these test results and service is given or...

Språk

Publicerad

2006-05-01
PDF · 533 SEK
ASTM C1674
Standard · ASTM ASTM C1674

Standard Test Method for Flexural Strength of Advanced Ceramics with Engineered Porosity (Honeycomb Cellular Channels) at Ambient Temperatures

1.1 This test method covers the determination of the flexural strength (modulus of rupture in bending) at ambient conditions of advanced ceramic structures with 2-dimensional honeycomb channel arch...

Språk

Publicerad

2011-05-20
PDF · 767 SEK
ASTM D5110
Standard · ASTM ASTM D5110

Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry

1.1 This practice covers a means for calibrating ambient, workplace, or indoor ozone monitors, and for certifying transfer standards to be used for that purpose. 1.2 This practice describes means b...

Språk

Publicerad

2004-10-01
PDF · 533 SEK
ASTM F1309
Standard · ASTM ASTM F1309

Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations

1.1 This practice covers the acceptable methods of fitting chocks to marine machinery foundations. 1.2

Språk

Publicerad

2003-12-01
PDF · 533 SEK
ASTM B548
Standard · ASTM ASTM B548

Standard Test Method for Ultrasonic Inspection of Aluminum-Alloy Plate for Pressure Vessels

1.1 This test method covers pulse-echo ultrasonic inspection of aluminum-alloy plate of thickness equal to or greater than 0.500 in. (12.7 mm) for use in the fabrication of pressure vessels. The ul...

Språk

Publicerad

2009-12-01
PDF · 533 SEK
ASTM D6675
Standard · ASTM ASTM D6675

Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel

1.1 This practice is designed to assist procedures to be followed when conducting outdoor exposures to evaluate cosmetic corrosion that might occur in steel panels covered with an organic coati...

Språk

Publicerad

2007-01-11
PDF · 468 SEK
ASTM D5831
Standard · ASTM ASTM D5831

Standard Test Method for Screening Fuels in Soils

1.1 This test method is a screening procedure for determining the presence of fuels containing aromatic compounds in soils. If the contaminant fuel is available for calibration, the approximate co...

Språk

Publicerad

2009-07-01
PDF · 533 SEK
ASTM D3271
Standard · ASTM ASTM D3271

Standard Practice for Direct Injection of Solvent-Reducible Paints Into a Gas Chromatograph for Solvent Analysis

1.1 This practice describes the techniques used to inject whole paint samples directly into a gas chromatograph to obtain a chromatogram from which the solvent composition may be e

Språk

Publicerad

2006-06-01
PDF · 468 SEK
ASTM D7281
Standard · ASTM ASTM D7281

Standard Test Method for Determining Water Migration Resistance Through Roof Membranes

1.1 This test method covers the determination of water migration resistance of roof membranes including built-up roof membranes, modified bitumen, and single ply roof membranes. Th

Språk

Publicerad

2007-09-05
PDF · 468 SEK
ASTM D7506/D7506M
Standard · ASTM ASTM D7506/D7506M

Standard Test Method for Pocket Reinforcement

1.1 This test method utilizes the grab procedures to determine localized weakness due to bar-tacking in the pocket areas of all types of garments. This can be utilized to test bar-tacking in the p...

Språk

Publicerad

2009-08-15
PDF · 468 SEK
ASTM E1340
Standard · ASTM ASTM E1340

Standard Guide for Rapid Prototyping of Information Systems

1.1 This guide covers a rapid prototyping method for developing information systems that is particularly relevant to systems for the healthcare sector. Intended readers of this guide are people wh...

Språk

Publicerad

2005-05-01
PDF · 611 SEK
ASTM B781
Standard · ASTM ASTM B781

Standard Guide for Silver-Cadmium Oxide Contact Material

1.1 This guide provides guidelines for users and manufacturers of silver-cadmium oxide material produced in strip, rod, wire, and part form for electrical contact applications. 1.2 This standard doe

Språk

Publicerad

2006-06-01
PDF · 533 SEK
ASTM E256
Standard · ASTM ASTM E256

Standard Test Method for Chlorine in Organic Compounds by Sodium Peroxide Bomb Ignition

1.1 This test method covers the determination of chlorine in organic compounds by sodium peroxide bomb ignition. It is intended for application to samples of organic materials containing more than ...

Språk

Publicerad

2009-10-01
PDF · 468 SEK
ASTM D6316
Standard · ASTM ASTM D6316

Standard Test Method for Determination of Total, Combustible and Carbonate Carbon in Solid Residues from Coal and Coke

1.1 This test method covers the determination of total, combustible, and carbonate carbon remaining in the solid byproducts of combustion from boiler furnaces and similar reactors, including ash, ...

Språk

Publicerad

2009-05-01
PDF · 533 SEK
ASTM G82
Standard · ASTM ASTM G82

Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance

1.1 This guide covers the development of a galvanic series and its subsequent use as a method of predicting the effect that one metal can have upon another metal can when they are in electrical co...

Språk

Publicerad

2003-10-01
PDF · 533 SEK
ASTM F1869
Standard · ASTM ASTM F1869

Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride

: 1.1 This test method covers the quantitative determination of the rate of moisture vapor emitted from below-grade, on-grade, and above-grade (suspended) bare concrete floors. 1.2 This test shall...

Språk

Publicerad

2011-09-16
PDF · 468 SEK
ASTM F2159
Standard · ASTM ASTM F2159

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethyl...

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes (3/8, ½, and &#x0 This specification establishes requireme...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM D5187
Standard · ASTM ASTM D5187

Standard Test Method for Determination of Crystallite Size (Lc of Calcined Petroleum Coke by X-Ray Diffraction

1.1 This test method covers the determination of the mean crystallite thickness of a representative, pulverized sample of calcined petroleum coke by interpretation of a X-ray diffraction pattern pr...

Språk

Publicerad

2010-09-17
PDF · 468 SEK
ASTM D5656
Standard · ASTM ASTM D5656

Standard Test Method for Thick-Adherend Metal Lap-Shear Joints for Determination of the Stress-Strain Behavior of Adhesives in Shear by Tension Loa...

1.1 This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives. 1.2 This test method covers data reduc...

Språk

Publicerad

2011-04-15
PDF · 533 SEK
Förfina din sökning genom att visa:
...som handlar om:

Ämnesområden (0)

Avbryt

Branscher (0)

Avbryt

Syfte (0)

Avbryt

Material (0)

Avbryt
Visa varukorgen Fortsätt handla 0
Varukorgen Stäng
Annonstext