21304 träffar på

Standard · ASTM ASTM B75

Standard Specification for Seamless Copper Tube

1.1 This specification establishes the requirements for seamless round, rectangular, and square copper tube suitable for general engineering applications. This specification establishes the requi...

Språk

Publicerad

2010-10-01

Upphävd

2011-10-15

PDF · 533 SEK

Standard · ASTM ASTM B108/B108M

Standard Specification for Aluminum-Alloy Permanent Mold Castings

1.1 This specification covers aluminum-alloy permanent mold castings designated as shown in Table 1. 1.2 This specification is not intended for aluminum-alloy permanent mold castings used in aeros...

Språk

Publicerad

2008-10-08

Upphävd

2011-12-01

PDF · 611 SEK

Standard · ASTM ASTM B213

Standard Test Method for Flow Rate of Metal Powders

Språk

Publicerad

2003-10-01

Upphävd

2011-11-15

PDF · 468 SEK

Standard · ASTM ASTM B243

Standard Terminology of Powder Metallurgy

Språk

Publicerad

2011-04-15

Upphävd

2011-11-15

PDF · 533 SEK

Standard · ASTM ASTM B253

Standard Guide for Preparation of Aluminum Alloys for Electroplating

1.1 This guide covers cleaning and conditioning treatments used before metal deposition (Section 5), and immersion deposit/strike procedures (Section 6) that enhance the adhesion of metals that a...

Språk

Publicerad

2010-11-01

Upphävd

2011-12-15

PDF · 533 SEK

Standard · ASTM ASTM B488

Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses

1.1 This specification covers requirements for electrodeposited gold coatings that contain not less than 99.00 mass % gold and that are used for engineering applications. 1.2 Specifically excluded ...

Språk

Publicerad

2001-01-01

Upphävd

2011-10-01

PDF · 533 SEK

Standard · ASTM ASTM B657

Guide for Metallographic Identification of Microstructure in Cemented Carbides

1.1 This test method covers apparatus and procedures for the metallographic determination of microstructures in cemented tungsten carbides. 1.2 This standard does not purport to address all of t...

Språk

Publicerad

2005-10-01

Upphävd

2011-10-01

PDF · 533 SEK

Standard · ASTM ASTM B769

Standard Test Method for Shear Testing of Aluminum Alloys

1.1 This test method covers double-shear testing of wrought and cast aluminum products to determine shear ultimate strengths. Note 1The values stated in inch-pound units are to be regarded as the s...

Språk

Publicerad

2007-09-05

Upphävd

2011-11-01

PDF · 468 SEK

Standard · ASTM ASTM B790/B790M

Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits

1.1 This practice is intended for the structural design of corrugated aluminum pipe and pipe-arches, and aluminum structural plate pipe, pipe-arches, and arches for use as culverts and storm sewers...

Språk

Publicerad

2006-03-01

Upphävd

2011-11-01

PDF · 533 SEK

Standard · ASTM ASTM B831

Standard Test Method for Shear Testing of Thin Aluminum Alloy Products

1.1 This test method covers single shear testing of thin wrought and cast aluminum alloy products to determine shear ultimate strengths.1.2 The values stated in inch-pound units are to be regarded ...

Språk

Publicerad

2005-04-01

Upphävd

2011-11-01

PDF · 468 SEK

Standard · ASTM ASTM B855

Standard Test Method for Volumetric Flow Rate of Metal Powders Using Arnold Meter and Hall Funnel

1.1 This test method covers a procedure for measuring the flow characteristics of a given volume of powder.1.2 The values stated in SI units are to be regarded as the standard (except for the Hall ...

Språk

Publicerad

2006-07-01

Upphävd

2011-11-15

PDF · 468 SEK

Standard · ASTM ASTM B951

Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

1.1 This practice provides a system for designating unalloyed magnesium and magnesium-alloys that have been used commercially since 1952, and thus is intended to be the registration source for unal...

Språk

Publicerad

2009-06-01

Upphävd

2010-02-01

PDF · 533 SEK

Standard · ASTM ASTM B951

Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

Språk

Publicerad

2008-08-06

Upphävd

2009-06-01

PDF · 533 SEK

Standard · ASTM ASTM B951

Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

Språk

Publicerad

2007-09-05

Upphävd

2008-03-01

PDF · 533 SEK

Standard · ASTM ASTM B951

Standard Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

Språk

Publicerad

2010-02-01

Upphävd

2011-11-01

PDF · 533 SEK

Standard · ASTM ASTM C500

Standard Test Methods for Asbestos-Cement Pipe

1.1 These test methods cover the testing of asbestos-cement pipe for hydrostatic strength, flexural strength, crushing strength, straightness, and uncombined calcium hydroxide; they are for use in ...

Språk

Publicerad

2008-02-06

Upphävd

2011-01-01

PDF · 1.066 SEK

Standard · ASTM ASTM D3168

Standard Practice for Qualitative Identification of Polymers in Emulsion Paints

1.1 This practice describes a procedure for the qualitative identification in emulsion paints of most types of polymers present as major components of the paint vehicle. Limitations are discussed i...

Språk

Publicerad

2005-01-01

Upphävd

2011-07-01

PDF · 533 SEK

Standard · ASTM ASTM F2903

Standard Guide for Tissue Engineered Medical Products (TEMPs) for Reinforcement of Tendon and Ligament Surgical Repair

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Standard · ASTM ASTM F1137

Standard Specification for Phosphate/Oil and Phosphate/Organic Corrosion Protective Coatings for Fasteners

1.1 This specification covers the basic requirements for four grades of corrosion protection for fasteners. Grade A consists of a zinc phosphate coating with no additional sealer (dry), Grade B co...

Språk

Publicerad

2011-06-17

PDF · 468 SEK

Standard · ASTM ASTM E2765

Standard Practice for Use of Image Capture and Storage Technology in Forensic Document Examination

1.1 This practice provides procedures to be used by forensic document examiners (Guide E444) using image capture and storage technology. <p id="s10

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Standard · ASTM ASTM D7775

Standard Guide for Measurements on Small Graphite Specimens

1.1 This guide covers best practice for properties measurements on small (nonstandard) graphite specimens and requirements for representing properties of the bulk material. This guide is aimed spec...

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Standard · ASTM ASTM D2482

Standard Test Method for Surface Strength of Paper (Wax Pick Method) (Withdrawn 2010)

1.1 This test method covers uncoated and coated papers. It is designed to measure the surface strength of paper or its resistance to picking. It is not applicable to loosely felted papers such as b...

Språk

Publicerad

1997-12-10

Upphävd

2010-02-01

PDF · 468 SEK

Standard · ASTM ASTM D2482

Standard Test Method for Surface Strength of Paper (Wax Pick Method) (Withdrawn 2010)

Språk

Publicerad

2007-09-05

Upphävd

2010-02-01

PDF · 468 SEK

Standard · ASTM ASTM D7620

Standard Test Method for Determination of Total Sulfur in Liquid Hydrocarbon Based Fuels by Continuous Injection, Air Oxidation and Ultraviolet Flu...

1.1 This test method covers the determination of total sulfur in liquid hydrocarbon based fuel with a final boiling point of up to 450°C. It is applicable to analysis of natural, proces...

Språk

Publicerad

2010-10-15

PDF · 533 SEK

Standard · ASTM ASTM D7688

Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) by Visual Observation

1.1 This test method covers the evaluation of the lubricity of diesel fuels using a high-frequency reciprocating rig (HFRR). 1.2 This test method is applicable to middle distillate fuels, such as G...

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Standard · ASTM ASTM D7744/D7744M

Standard Test Methods for Tensile Testing of High Performance Polyethylene Tapes

1.1 The test method covers the tensile testing of high performance polyethylene tapes. The method includes testing procedure only and includes no specifications or tolerances. 1.2 The values stated...

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Standard · ASTM ASTM D7627

Standard Practice for Minimum Geospatial Data for Land Reclamation and Performance Bond Status of a Permitted Coal Mine

1.1 This practice covers the minimum elements for the accurate location and description of geospatial data for defining the land reclamation and performance bond status of a permitted coal mine. 1...

Språk

Publicerad

2010-05-15

PDF · 533 SEK

Standard · ASTM ASTM C1675

Standard Practice for Installation of Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers

1.1 This practice covers the installation of precast reinforced concrete box sections cast monolithically and intended to be used for the conveyance of storm water, industrial wastes and sewage, an...

Språk

Publicerad

2012-02-24

PDF · 468 SEK

Standard · ASTM ASTM E2837

Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonra...

1.1 This fire-test-response test method measures the performance of a unique fire resistive joint system called a continuity head-of-wall joint system, which is designed to be used between a

Språk

Publicerad

2012-02-24

PDF · 611 SEK

Standard · ASTM ASTM D7721

Standard Practice for Determining the Effect of Fluid Selection on Hydraulic System or Component Efficiency

1.1 This practice covers all hydraulic fluids. 1.2 This practice is applicable to both laboratory and field evaluations. 1.3 This practice gives overall guidelines for conducting science-based eval...

Språk

Publicerad

2012-02-24

PDF · 533 SEK

Förfina din sökning genom att visa:

...som handlar om: