21324 träffar på

Standard · ASTM ASTM F1927

Standard Test Method for Determination of Oxygen Gas Transmission Rate, Permeability and Permeance at Controlled Relative Humidity Through Barrier ...

1.1 This test method covers a procedure for determination of the rate of transmission of oxygen gas, at steady-state, at a given temperature and %RH level, through film, sheeting, laminates, co-ext...

Språk

Publicerad

2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM D3409

Standard Test Method for Adhesion of Asphalt-Roof Cement to Damp, Wet, or Underwater Surfaces

1.1 This test method covers the determination of the adhesion of asphalt roofing cements to damp, wet, or underwater surfaces. 1.2 The values in SI units are to be regarded as standard. The values ...

Språk

Publicerad

2008-05-01

PDF · 468 SEK

Standard · ASTM ASTM D3209

Standard Test Method for Freeze/Thaw Resistance of Polymer Floor Polishes

1.1 This test method covers the determination of the stability of polymer emulsion floor polishes when these are exposed to repeated cycles of freezing and thawing. Possible degradation of the emul...

Språk

Publicerad

2008-03-01

PDF · 468 SEK

Standard · ASTM ASTM F1838

Standard Performance Requirements for Child's Plastic Chairs for Outdoor Use

1.1 These standard performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) child's plastic chairs intended for outdo...

Språk

Publicerad

2008-08-01

PDF · 468 SEK

Standard · ASTM ASTM D5714

Standard Specification for Content of Digital Geospatial Metadata (Withdrawn 2011)

1.1 This specification covers the information content of metadata for a set of digital geospatial data. This specification provides a common set of terminology and definitions for concepts related ...

Språk

Publicerad

1995-04-15

Upphävd

2011-01-01

PDF · 611 SEK

Standard · ASTM ASTM D2967

Standard Test Method for Corner Coverage of Powder Coatings

1.1 This test method covers the determination of the ratio of corner thickness (see 3.1.3) to face thickness (see ) of powder coatings applied to a specific face thickness by dipping preheated squa...

Språk

Publicerad

2007-09-05

PDF · 468 SEK

Standard · ASTM ASTM C492

Standard Test Method for Hydration of Granular Dead-Burned Refractory Dolomite

1.1 This test method covers the determination of the amount of hydration of a granular dead-burned refractory dolomite when exposed to moist air. 1.2 The values stated in inch-pound units are to re...

Språk

Publicerad

2008-03-01

PDF · 468 SEK

Standard · ASTM ASTM F1729

Standard Practice for Single Person Cold Water Survival/Rescue Technique: HELP Position

1.1 This practice covers the recommended water rescue procedure for performing the heat escape lessening posture (HELP) position.1.2 This practice is one in a set of self-rescue techniques for the ...

Språk

Publicerad

2007-12-05

PDF · 468 SEK

Standard · ASTM ASTM F2250

Standard Practice for Evaluation of Chemical Resistance of Printed Inks and Coatings on Flexible Packaging Materials

1.1 This practice describes the procedure for evaluating the ability of an ink, overprint varnish or coating to withstand chemical exposure. Typical chemicals, which may come in contact with the pa...

Språk

Publicerad

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM F34

Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials

1.1 This practice covers the construction of test cells which may be used for the extraction of components from flexible barrier materials by suitable extracting liquids, including foods and food s...

Språk

Publicerad

2007-09-05

PDF · 468 SEK

Standard · ASTM ASTM D4718

Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles

1.1 This practice presents a procedure for calculating the unit weights and water contents of soils containing oversize particles when the data are known for the soil fraction with the oversize par...

Språk

Publicerad

1987-07-31

PDF · 468 SEK

Standard · ASTM ASTM D4795

Standard Test Method for Nitrogen Content of Soluble Nitrocellulose—Alternative Method

1.1 Test Methods D 301 for measuring nitrogen content in nitrocellulose by nitrometer are the accepted standard. However, the glassware is specialized and the precision is dependent on the devel...

Språk

Publicerad

2008-06-01

PDF · 468 SEK

Standard · ASTM ASTM F1440

Standard Practice for Cyclic Fatigue Testing of Metallic Stemmed Hip Arthroplasty Femoral Components Without Torsion

1.1 This practice describes a method for the fatigue testing of metallic stemmed femoral components used in hip arthroplasty. The described method is intended to be used to evaluate the comparison...

Språk

Publicerad

2008-06-01

PDF · 533 SEK

Standard · ASTM ASTM D3716

Standard Test Methods for Use of Emulsion Polymers in Floor Polishes

1.1 These test methods cover test procedures for emulsion polymers that are used in water-based floor polishes. The term “emulsion polymers” is used primarily to denote

Språk

Publicerad

2008-03-01

PDF · 533 SEK

Standard · ASTM ASTM D7284

Standard Test Method for Total Cyanide in Water by Micro Distillation followed by Flow Injection Analysis with Gas Diffusion Separation and Amperom...

1.1 This test method is used to determine the concentration of total cyanide in an aqueous wastewater or effluent. The method detects the cyanides that are free (HCN and CN-) and strong-metal-cya...

Språk

Publicerad

2008-05-14

PDF · 533 SEK

Standard · ASTM ASTM D5108

Standard Test Method for Organotin Release Rates of Antifouling Coating Systems in Sea Water

1.1 This test method covers the laboratory determination of the rate at which organotin expressed as tributyltin (TBT) is released from an antifouling (AF) coating in synthetic sea water using grap...

Språk

Publicerad

2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM D5770

Standard Test Method for Semiquantitative Micro Determination of Acid Number of Lubricating Oils During Oxidation Testing

1.1 This test method is a semiquantitative micro method intended for monitoring the changes in acidic constituents occurring in lubricating oils during oxidation testing, when the acid number of su...

Språk

Publicerad

2002-12-10

PDF · 468 SEK

Standard · ASTM ASTM B487

Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of a Cross Section

1.1 This test method covers measurement of the local thickness of metal and oxide coatings by the microscopical examination of cross sections using an optical microscope.1.2 Under good conditions, ...

Språk

Publicerad

2007-05-09

PDF · 468 SEK

Standard · ASTM ASTM E1512

Standard Test Methods for Testing Bond Performance of Bonded Anchors

1.1 These test methods cover instructions for making a variety of tests for the strength of the adhesive bond developed between a steel anchor and the surface of a hole in concrete or masonry (incl...

Språk

Publicerad

2007-05-09

PDF · 533 SEK

Standard · ASTM ASTM D4567

Standard Test Method for Single-Point Determination of Specific Surface Area of Catalysts and Catalyst Carriers Using Nitrogen Adsorption by Contin...

1.1 This test method covers the single-point determination of the surface area of catalysts and catalyst carriers that exhibit Type II or Type IV nitrogen adsorption isotherms using a nitrogen-hel...

Språk

Publicerad

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM C982

Standard Guide for Selecting Components for Energy-Dispersive X-Ray Fluorescence (XRF) Systems (Withdrawn 2008)

1.1 This guide describes the components for an energy-dispersive X-ray fluorescence (XRF) system for materials analysis. It can be used as a reference in the apparatus section of test methods for e...

Språk

Publicerad

2003-07-10

Upphävd

2008-12-22

PDF · 468 SEK

Standard · ASTM ASTM E2066

Standard Guide for Validation of Laboratory Information Management Systems

1.1 This guide describes an approach to the validation process for a Laboratory Information Management System (LIMS).1.2 This guide is for validation of a commercial LIMS purchased from a vendor. T...

Språk

Publicerad

2007-05-09

PDF · 767 SEK

Standard · ASTM ASTM D3528

Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading

1.1 This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive s...

Språk

Publicerad

2008-04-01

PDF · 468 SEK

Standard · ASTM ASTM F2214

Standard Test Method for In Situ Determination of Network Parameters of Crosslinked Ultra High Molecular Weight Polyethylene (UHMWPE)

1.1 This test method describes how the crosslink density, molecular weight between crosslinks, and number of repeat units between crosslinks in ultra-high molecular weight polyethylene (UHMWPE) cro...

Språk

Publicerad

2008-05-01

PDF · 533 SEK

Standard · ASTM ASTM D5955

Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM

1.1 These test methods pertain to the sampling/analysis of respirable suspended particles (RSP) and the estimation of the RSP fraction attributable to environmental tobacco smoke (ETS). These test ...

Språk

Publicerad

2007-09-05

PDF · 533 SEK

Standard · ASTM ASTM D4106

Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis N...

1.1 This test method covers an analytical procedure for determining the transmissivity and storage coefficient of a nonleaky confined aquifer. It is used to analyze data on water-level response col...

Språk

Publicerad

2008-09-15

PDF · 533 SEK

Standard · ASTM ASTM E968

Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters

1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from − 130 °C to + 800 &#x00B

Språk

Publicerad

2008-09-01

PDF · 533 SEK

Standard · ASTM ASTM F1045

Standard Performance Specification for Ice Hockey Helmets

1.1 This performance specification covers performance requirements for ice hockey helmets.1.2 The intent of this performance specification is to reduce the risk of injury to the head without compro...

Språk

Publicerad

2007-10-10

PDF · 533 SEK

Standard · ASTM ASTM F2183

Standard Test Method for Small Punch Testing of Ultra-High Molecular Weight Polyethylene Used in Surgical Implants

1.1 This test method covers the determination of mechanical behavior of ultra-high molecular weight polyethylene (UHMWPE) by small punch testing of miniature disk specimens (0.5 mm in thickness and...

Språk

Publicerad

2008-05-01

PDF · 533 SEK

Standard · ASTM ASTM E900

Standard Guide for Predicting Radiation-Induced Transition Temperature Shift in Reactor Vessel Materials, E706 (IIF)

1.1 This guide presents a method for predicting reference transition temperature adjustments for irradiated light-water cooled power reactor pressure vessel materials based on Charpy V-notch 30-ftl...

Språk

Publicerad

2002-06-10

PDF · 468 SEK

Förfina din sökning genom att visa:

...som handlar om:

21324 träffar på

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Upphävd

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Upphävd

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Språk

Publicerad

Ämnesområden (0)

Branscher (0)

Syfte (0)

Material (0)