1.1 This specification covers thermoset plastics based on diglycidyl ethers of bisphenol A and amino functional curing agents or amine catalysts. 1.2 The epoxy encapsulants covered by this specific...
2009-08-01
1.1 This practice provides two options for the qualification of cotton classification instruments: option 1, newly installed cotton classification instrumentation, or option 2, annual verifi
2008-03-12
1.1 These test methods cover only the analyses usually required on the following commercial products: 1.1.1 Caustic soda (sodium hydroxide), 50 and 73 % liquors; anhydrous (solid, flake, ground, or...
2009-04-01
1.1 This practice covers a procedure for acousto-ultrasonic (AU) assessment of filament-wound pressure vessels. Guidelines are given for the detection of defect states and flaw populations that ari...
2010-08-20
1.1 This specification covers Penrose-type rubber tubes used in performing certain surgical drainage procedures. 1.2 The specification provides for packaged sterile rubber tubes and packaged or bul...
2010-10-15
1.1 This test method covers the determination of extraneous materials weathering above 38°C that are present in liquefied petroleum gases. The extraneous materials will generally be diss...
2011-05-20
1.1 This specification covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 3, in the following finishes: 1.1.1 Plate in a...
2011-09-16
1.1 This test method covers only a laboratory test for determining the relative carpet dirt removal effectiveness of household/commercial vacuum cleaners when tested under specified conditions. 1.2...
1.1 This practice describes a method for direct sampling and analysis of process vents for volatile organic compound (VOC) vapors and permanent gases using a portable gas chromatograph (GC). 1.2 Th...
2009-10-01
1.1 It is common practice for orthopaedic implant manufacturers to apply permanent identification to implant components. In this regard, Practice F 86 describes recommended locations and methods ...
1.1 This guide may be used for the control and maintenance of recorded and unrecorded magnetic and optical media of analog or digital electronic data from industrial radioscopy. 1.2 The values stat...
2009-07-01
1.1 The guide covers the development of criteria for the acoustical performance of a broad variety of acoustical enclosures by identifying information necessary to unambiguously describe acoustical...
1995-06-15
1.1 This practice covers the characteristic mechanical behavior of rubbers at low temperatures, and outlines the conditioning procedure necessary for testing at these temperatures
2007-09-05
1.1 This classification is to serve as an international standard for marine equipment nomenclature, taxonomy, hierarchical data structure, unique identifiers, and boundary definition for the consis...
2004-12-01
1.1 This specification covers uncoated stress-relieved steel bars for use in prestressed concrete railroad ties. 1.2 A supplementary requirement (S1) is provided for use where low-relaxation bars...
1.1 This test method was developed using copper electrodes to evaluate the low-voltage (up to 600 V) tracking resistance of materials in the presence of aqueous contaminants. Note</span
2010-01-15
1.1 This guide covers obtaining cores of soil-cement or lime-stabilized soil for use in determining compressive strength, lift thickness and bond strength, and other physical properties. This guide...
1.1 This test method covers the evaluation of the thermal stability of hydrocarbon–based way lubricants, although oxidation may occur during the test. 1.2 The values stated in SI units
2007-02-07
1.1 These test methods cover the determination of flammability hazards for aerosol products. 1.2

2006-04-01
1.1 This specification covers nickel-chromium-molybdenum alloy steel plates for use in the quenched and tempered condition, intended for the fabrication of welded pressure vessels and other pre...
1.1 This specification covers in-situ applied, single-pack, moisture-triggered, aliphatic polyurethanes intended to form an elastomeric single-ply membrane, once cured. The cured membrane may or m...
2010-08-01
1.1 This test method describes the procedure for the measurement of the depth of the rut at a chosen location in a pavement surface using a straightedge and a gauge. 1.2 The values stated in eithe...
1.1 This fire-test-response test method describes a small-scale horizontally oriented burning test procedure for comparing the relative rate of burning and the extent and time of burning of cellula...
2010-01-01
1.1 This specification covers foaming agents specifically formulated for making preformed foam for use in the production of cellular concrete. 1.2 The function of this specification is to provide ...
1.1 This test method covers a procedure for determining the ball-pan hardness number of granular activated carbons. For the purpose of this test, granular activated carbons are those having partic...
2010-05-17
1.1 This guide provides examples of performance statements for functional and operable, spaces, products, components, and subsystems for single family attached and detached dwelli
2004-10-01
1.1 This practice covers a procedure to determine the weight of toner used for printing a single page derived from an electrophotographic process. The practice uses a printer text target specifical...
1.1 This practice covers the preparation of solutions containing inorganic salts in proportions and concentrations representative of ocean water.<
2008-07-15
1.1 This test method covers determination of curing parameters of pultrusions resins by differential scanning calorimetry. 1.2 This test method is applicable to pultrusion resin solutions with adeq...
2009-09-01
1.1 Practice A, Pressurization—This practice covers procedures for calibration of ultrasonic instruments, location, and estimated measurements of gas leakage to atmosphere by the