21292 träffar på

Standard · ASTM ASTM F1469 Standard Guide for Conducting a Repeatability and Reproducibility Study on Test Equipment for Nondestructive Testing 1.1 This guide describes the steps required to conduct a complete repeatability and reproducibility (RR) study on nondestructive test equipment. This guide is a manual (use of calculator) method. ... Språk Publicerad 2010-05-01 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM F1962 Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Cross... 1.1 This guide describes the design, selection considerations, and installation procedures for the placement of polyethylene pipe or conduit below ground using maxi-horizontal directional drilling ... Språk Publicerad 2005-04-01 Upphävd 2011-05-01

PDF · 611 SEK

Standard · ASTM ASTM F2280 Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Steel, Heat Treated, 150 ... 1.1 This specification covers two types of heat treated, steel, tension control bolt-nut-washer assemblies, also referred to as “sets,” having a tensile strength of 150 to 17... Språk Publicerad 2008-03-12 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM F2788 Standard Specification for Crosslinked Polyethylene (PEX) Pipe 1.1 This specification covers crosslinked polyethylene (PEX) pipe that is outside diameter controlled, made in nominal pipe dimension ratios, and pressure rated for water at three temperatures (see... Språk Publicerad 2009-08-01 Upphävd 2011-05-01

PDF · 611 SEK

Standard · ASTM ASTM C1600/C1600M Standard Specification for Rapid Hardening Hydraulic Cement 1.1 This specification is for rapid hardening hydraulic cements. This is a specification giving performance requirements. There are no restrictions on the composition of the cement or its constitue... Språk Publicerad 2008-09-01 Upphävd 2011-04-01

PDF · 468 SEK

Standard · ASTM ASTM C1600/C1600M Standard Specification for Rapid Hardening Hydraulic Cement 1.1 This specification is for rapid hardening hydraulic cements. This is a specification giving performance requirements. There are no restrictions on the composition of the cement or its constitue... Språk Publicerad 2008-12-03 Upphävd 2011-04-01

PDF · 468 SEK

Standard · ASTM ASTM A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applicat... 1.1 This specification covers alloy and stainless steel bolting for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applicat... Språk Publicerad 2010-06-18 Upphävd 2011-05-01

PDF · 611 SEK

Standard · ASTM ASTM A320/A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service 1.1 This specification covers alloy steel bolting for pressure vessels, valves, flanges, and fittings for low-temperature service. See Specification for t This specification covers alloy steel bo... Språk Publicerad 2011-03-18 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A426/A426M Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service 1.1 This specification covers centrifugally cast alloy steel pipe intended for use in high-temperature, high-pressure service. 1.2 Several grades of ferritic steels are covered. Their compositions... Språk Publicerad 2011-03-18 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A479/A479M Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels 1.1 This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use ... Språk Publicerad 2010-05-17 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A491 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric 1.1 This specification covers aluminum-coated steel chain-link fence fabric, aluminum-coated before weaving. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values... Språk Publicerad 2007-11-07 Upphävd 2010-07-01

PDF · 533 SEK

Standard · ASTM ASTM A491 Standard Specification for Aluminum-Coated Steel Chain-Link Fence Fabric 1.1 This specification covers aluminum-coated steel chain-link fence fabric, aluminum-coated before weaving. 1.2 The values stated in inch-pound units are to be regarded as the standard. The value... Språk Publicerad 2010-08-20 Upphävd 2011-06-01

PDF · 533 SEK

Standard · ASTM ASTM A522/A522M Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service 1.1 This specification covers 8 and 9 % nickel-alloy steel forged or rolled flanges, fittings, valves, and parts intended for use in welded pressure vessels for low-temperature service. The specifi... Språk Publicerad 2007-05-09 Upphävd 2011-05-01

PDF · 468 SEK

Standard · ASTM ASTM A709/A709M Standard Specification for Structural Steel for Bridges 1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. S... Språk Publicerad 2010-11-19 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A961/A961M Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications 1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual pro... Språk Publicerad 2008-10-01 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A962/A962M Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range 1.1 This specification covers a group of common requirements that shall apply to carbon, alloy, stainless steel, and nickel alloy bolting under any of the following ASTM Specifications (or under an... Språk Publicerad 2011-03-18 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A988/A988M Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service 1.1 This specification covers hot isostatically-pressed, powder metallurgy, stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts ... Språk Publicerad 2007-11-07 Upphävd 2011-05-01

PDF · 611 SEK

Standard · ASTM ASTM A989/A989M Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service 1.1 This specification covers hot isostatically-pressed, powder metallurgy, alloy steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts made... Språk Publicerad 2007-11-07 Upphävd 2011-05-01

PDF · 533 SEK

Standard · ASTM ASTM A992/A992M Standard Specification for Structural Steel Shapes 1.1 This specification covers rolled steel structural shapes for use in building framing or bridges, or for general structural purposes.1.2 Supplementary requirements are provided for use where add... Språk Publicerad 2006-07-01 Upphävd 2011-05-01

PDF · 468 SEK

Standard · ASTM ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) 1.1 This test method covers determination of the compressive strength of hydraulic cement mortars, using 2-in. or [50-mm] cube specimens. Note 1 - Test Method C 349 provides an alternative procedur... Språk Publicerad 2007-10-10 Upphävd 2008-12-01

PDF · 533 SEK

Standard · ASTM ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) 1.1 This test method covers determination of the compressive strength of hydraulic cement mortars, using 2-in. or [50-mm] cube specimens. Note 1&#8212;Test Method C 349<astmref rid Språk Publicerad 2008-12-01 Upphävd 2011-04-01

PDF · 533 SEK

Standard · ASTM ASTM C187 Standard Test Method for Normal Consistency of Hydraulic Cement 1.1 This test method covers the determination of the normal consistency of hydraulic cement. 1.2 Units—The values stated in SI units are to be regarded as sta Språk Publicerad 2010-08-20 Upphävd 2011-04-01

PDF · 468 SEK

Standard · ASTM ASTM C305 Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency 1.1 This practice covers the mechanical mixing of hydraulic cement pastes and mortars of plastic consistency.This standard does not purport to address all of the safety concerns, if any, associated... Språk Publicerad 2006-08-01 Upphävd 2011-04-01

PDF · 468 SEK

Standard · ASTM ASTM C591 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation 1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocyanurate plastic material intended for use as thermal insulation on surface... Språk Publicerad 2007-09-05 Upphävd 2008-06-01

PDF · 533 SEK

Standard · ASTM ASTM C591 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation 1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocyanurate plastic material intended for use as thermal insulation on surfac... Språk Publicerad 2009-11-01 Upphävd 2011-05-15

PDF · 533 SEK

Standard · ASTM ASTM C591 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation 1.1 This specification covers the types, physical properties, and dimensions of unfaced, preformed rigid cellular polyisocyanurate plastic material intended for use as thermal insulation on surfac... Språk Publicerad 2008-11-05 Upphävd 2009-11-01

PDF · 533 SEK

Standard · ASTM ASTM C871 Standard Test Methods for Chemical Analysis of Thermal Insulation Materials for Leachable Chloride, Fluoride, Silicate, and Sodium Ions 1.1 These test methods cover laboratory procedures for the determination of water-leachable chloride, fluoride, silicate, and sodium ions in thermal insulation materials in the parts per million r... Språk Publicerad 2008-05-14 Upphävd 2011-05-15

PDF · 533 SEK

Standard · ASTM ASTM C1093 Standard Practice for Accreditation of Testing Agencies for Masonry 1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system, and it establishes minimum qualifications for agencies engaged in the ... Språk Publicerad 2007-09-05 Upphävd 2008-07-01

PDF · 533 SEK

Standard · ASTM ASTM C1093 Standard Practice for Accreditation of Testing Agencies for Masonry 1.1 This practice covers the minimum requirements for laboratory personnel, for establishing and maintaining a quality system, and it establishes minimum qualifications for agencies engaged in the ... Språk Publicerad 2009-12-01 Upphävd 2011-06-01

PDF · 533 SEK

Standard · ASTM ASTM C55 Standard Specification for Concrete Building Brick 1.1 This specification covers solid, dry-cast, concrete building brick intended for interior and exterior use in constructing structural masonry, and are made from portland cement, water, and s... Språk Publicerad 2009-12-01 Upphävd 2011-06-01

PDF · 468 SEK

• < Föregående
• 356
• 357
• 358
• 359
• 360
• 361
• 362
• 363
• 364
• 365
• Nästa >