1.1 This practice provides a standard qualifying method for coating applicators to verify their proficiency and ability to attain the required quality for application of specified coatin This pract...
2005-12-01
1.1 This test method covers the detection of gross leaks in packaging. Method sensitivity is down to 250 μm (0.010 in.) with an 81 % probability (see Section 11). This test method may be...
2012-03-23
1.1 This practice establishes orientation codes for continuous-fiber-reinforced composite materials. Orientation codes are explicitly provided for two-dimensional laminates and braids. The laminate...
2011-05-20
1.1 This guide provides guidelines for the identification and packaging of rolled geosynthetics by the manufacturer and for the handling and storage of geosynthetics by the end user. This guide is...
2002-01-10
1.1 This test method covers the determination of tire plunger energy required to completely penetrate the tread area of an inflated tire as indicated by a rupture, loss of inflation pressure, sudde...
2009-06-15
1.1 This test method covers the procedure for the determination of mineral stabilizer content in prefabricated bituminous geomembranes (BGM) by calcination. 1.2 The values stated in SI units are to...
2006-11-15
1.1 This guide covers the qualification of analysts to perform chemical analysis or physical measurements of nuclear fuel cycle materials. The guidance is general in that it is applicable to all an...
2003-07-10
1.1 This test method covers the laboratory measurement of both the acoustical and mechanical performance of pneumatic exhaust silencers designed for quieting compressed gas (usuall
2004-08-01
1.1 This specification covers composite corrugated steel pipe, intended for uses such as storm water drainage, sanitary sewers, underdrains, construction of culverts, and similar uses. The composit...
2009-11-01
1.1 This test method provides a means of evaluating the springback behavior of metals in a test that simulates a stretch-draw forming process. The test method can also be used to calibrate computer...
2007-06-01
1.1 This practice provides minimum requirements for a quality assurance program. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the re
2010-10-15
1.1 This specification covers bearings, which consist of all elastomer or of alternate laminates of elastomer and steel, when the function of the bearings is to transfer loads or a This ...
2008-03-12
1.1 This practice covers a policy (“the policy”) for digital certificates that support the authentication, authorization, confidentiality, integrity, and nonrepudiatio
2002-11-10
1.1 These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. <a name="
2007-09-05
1.1 This standard covers a test method for measurement of thermal impedance and calculation of an apparent thermal conductivity for thermally conductive electrical insulation materials ranging from...
2012-02-24
1.1 This specification covers several grades of silicon metal. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions...
2005-05-01
1.1 This test method covers the determination of bitumen content in materials containing at least 25 % bitumen. Bitumen content may usually be expeditiously and accurately determined by Procedure N...
2004-07-01
1.1 This test method covers equipment and techniques for determining porosity in noble metal coatings, particularly electrodeposits and clad metals used on electrical contacts. 1.2 The test method ...
2009-10-01
1.1 This test method describes a procedure for the determination of total ash content of activated carbon.1.2 This standard does not purport to address all of the safety concerns, if any, associate...
2011-09-16
1.1 This practice covers equipment and procedures for the use of earth augers in shallow depth geotechnical exploration. This practice does not apply to hollow-stem augers. Uses of hollow-stem aug...
2009-02-15
1.1 This specification covers regular and monomer grade 2-ethylhexanol. 1.2 The following appli This specification the properties and requirements for regular and monomer gra...
1.1 This specification covers bare concentric-lay-stranded conductors made from bare, hard-drawn, round, aluminum-clad steel wires of 20.3 % conductivity for general use of e T...
1998-03-10
1.1 This test method covers the determination of the resistance of exterior metal roof panel systems to air infiltration resulting from either positive or negative air pressure differences. The tes...
1.1 This test method covers the comparative behavior of refractories under the disintegrating action of carbon monoxide(CO). The test method is an accelerated exposure to CO to determine potential...
2009-03-01
1.1 These test methods cover the measurements of saturated hydraulic conductivity, water retention, porosity (including distribution of capillary and air-filled porosity at a known soil suction), a...
2011-06-17
1.1 This test method covers the measurement of sulfur in nonleaded gasoline and gasoline-oxygenate blends. The applicable concentration range is 48 to 1000 mg/kg sulfur. 1.2 The values stated in SI...
2004-05-01
2009-09-01
1.1 This guide covers sputtering targets used as thin film source material in fabricating semiconductor electronic devices. It should be used to develop target specifications for specific materials...
1.1 This specification covers aluminum-alloy die castings of all compositions. Thirteen of the most commonly die cast alloy compositions are specified, designated as shown in Table 1. 1.2 This spec...
2011-03-18
1.1 This guide provides a format for documenting information and performance data for a airborne particle penetration test. 1.2 Documented data and information are grouped into five categories that...
2006-06-01
1.1 This practice2 covers procedures for evaluating the following performance characteristics This practice covers procedures for evaluating the performance characteristics of air qualit...