21298 träffar på

ASTM A760/A760M
Standard · ASTM ASTM A760/A760M

Standard Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains

1.1 This specification covers corrugated steel pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not...

Språk

Publicerad

2010-10-15
PDF · 611 SEK
ASTM E794
Standard · ASTM ASTM E794

Standard Test Method for Melting And Crystallization Temperatures By Thermal Analysis

1.1 This test method describes the determination of melting (and crystallization) temperatures of pure materials by differential scanning calorimetry (DSC) and differential thermal

Språk

Publicerad

2006-03-01
PDF · 468 SEK
ASTM C803/C803M
Standard · ASTM ASTM C803/C803M

Standard Test Method for Penetration Resistance of Hardened Concrete

1.1 This test method covers the determination of the resistance of hardened concrete to penetration by either a steel probe or pin. 1.2 The values stated in either SI units or inch-pound units ...

Språk

Publicerad

2003-01-10
PDF · 533 SEK
ASTM D3631
Standard · ASTM ASTM D3631

Standard Test Methods for Measuring Surface Atmospheric Pressure

1.1 These methods cover the measurement of atmospheric pressure with two types of barometers: the Fortin-type mercurial barometer and the aneroid barometer. 1.2 In the absence of abnormal perturbat...

Språk

Publicerad

2008-02-06
PDF · 533 SEK
ASTM D3605
Standard · ASTM ASTM D3605

Standard Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission Spectroscopy

1.1 This test method covers the determination of sodium, lead, calcium, and vanadium in Specification D2880 Grade Nos. 1-GT and 2-GT fuels in the range

Språk

Publicerad

2005-05-01
PDF · 468 SEK
ASTM D5329
Standard · ASTM ASTM D5329

Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements

1.1 These test methods cover tests for hot-applied types of joint and crack sealants and fillers for portland cement concrete and asphaltic concrete pavements. There are numerous standard materia...

Språk

Publicerad

2009-06-01
PDF · 533 SEK
ASTM D6797
Standard · ASTM ASTM D6797

Standard Test Method for Bursting Strength of Fabrics Constant-Rate-of-Extension (CRE) Ball Burst Test

1.1 This test method describes the measurement for bursting strength of woven and knitted textiles taken from rolls of fabric or fabric taken from garments. Note 1—For the

Språk

Publicerad

2007-09-05
PDF · 468 SEK
ASTM F2340
Standard · ASTM ASTM F2340

Standard Specification for Developing and Validating Prediction Equation(s) or Model(s) Used in Connection with Livestock, Meat, and Poultry Evalua...

1.1 This specification covers methods to collect and analyze data, document the results, and make predictions by any objective method for any characteristic used to determine value in any species u...

Språk

Publicerad

2005-12-01
PDF · 468 SEK
ASTM D234
Standard · ASTM ASTM D234

Standard Specification for Raw Linseed Oil (Withdrawn 2007)

1.1 This specification covers raw linseed oil.

Språk

Publicerad

1998-05-10

Upphävd

2007-03-16
PDF · 468 SEK
ASTM D3122
Standard · ASTM ASTM D3122

Standard Specification for Solvent Cements for Styrene-Rubber (SR) Plastic Pipe and Fittings

1.1 This specification provides general requirements for styrene-rubber solvent cements to be used in joining styrene-rubber (SR) plastic pipe and fittings. 1.2 A recommended procedure for joining...

Språk

Publicerad

1995-09-10
PDF · 468 SEK
ASTM D3612
Standard · ASTM ASTM D3612

Standard Test Method for Analysis of Gases Dissolved in Electrical Insulating Oil by Gas Chromatography

1.1 This test method covers three procedures for extraction and measurement of gases dissolved in electrical insulating oil having a viscosity of 20 cSt (100 SUS) or less at 40°C (104&l...

Språk

Publicerad

2002-10-10
PDF · 767 SEK
ASTM E969
Standard · ASTM ASTM E969

Standard Specification for Glass Volumetric (Transfer) Pipets

1.1 This specification covers volumetric pipets of two classes. Class A, Precision Pipet and Class B, General Purpose. This specification covers volumetric pipets of two classes. Class A...

Språk

Publicerad

2002-10-10
PDF · 468 SEK
ASTM B735
Standard · ASTM ASTM B735

Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor

1.1 This test method covers equipment and procedures for using nitric acid vapor for determining porosity in gold coatings, greater than 0.6 μm (25 μin.) in thickness,

Språk

Publicerad

2007-01-11
PDF · 468 SEK
ASTM A638/A638M
Standard · ASTM ASTM A638/A638M

Standard Specification for Precipitation Hardening Iron Base Superalloy Bars, Forgings, and Forging Stock for High-Temperature Service

1.1 This specification covers hot-finished or cold-finished precipitation hardening iron base superalloy bars, forgings, and forging stock for high-temperature service. The mechanical properties ...

Språk

Publicerad

2010-05-17
PDF · 468 SEK
ASTM C51
Standard · ASTM ASTM C51

Standard Terminology Relating to Lime and Limestone (as used by the Industry)

1.1 This terminology refers to the terms relating to lime and limestone products as used by the industry. 1.2 Where appropriate, the various terms defined below should be prefixed with one or other...

Språk

Publicerad

2011-08-25
PDF · 468 SEK
ASTM D5933
Standard · ASTM ASTM D5933

Standard Specification for 258-in. and 4-in. Diameter Metal Shear Plates for Use in Wood Constructions

1.1 This specification covers standardizing the dimensions and materials for the manufacture of 25/8 and 4-in. diameter steel or cast iron shear plates This specification cove...

Språk

Publicerad

2007-05-09
PDF · 533 SEK
ASTM E1605
Standard · ASTM ASTM E1605

Standard Terminology Relating to Lead in Buildings

1.1 This terminology standard covers definitions for the following: 1.1.1 Terms that are commonly used in the field of management of lead hazards in facilities; 1.1.2 Architectural terms, particularly

Språk

Publicerad

2004-11-01
PDF · 533 SEK
ASTM E2550
Standard · ASTM ASTM E2550

Standard Test Method for Thermal Stability by Thermogravimetry

1.1 This test method covers the assessment of material thermal stability through the determination of the temperature at which the materials start to decompose or react and the extent of the ma...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM C1320
Standard · ASTM ASTM C1320

Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction

1.1 This practice covers procedures for the installation of mineral fiber batt and blanket thermal insulation in ceilings, attics, floors, and walls of new or existing housing and other light fram...

Språk

Publicerad

2011-04-15
PDF · 468 SEK
ASTM B148
Standard · ASTM ASTM B148

Standard Specification for Aluminum-Bronze Sand Castings

1.1 This specification establishes requirements for sand castings produced from copper-base alloys having the alloy numbers, commercial designations, and nominal compositions shown in Table 1. 1.2...

Språk

Publicerad

2003-04-10
PDF · 533 SEK
ASTM D1195/D1195M
Standard · ASTM ASTM D1195/D1195M

Standard Test Method for Repetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport ...

1.1 This test method covers a procedure for making repetitive static plate load tests on subgrade soils and compacted pavement components, in either the compact condition or the natural state, and...

Språk

Publicerad

2009-11-01
PDF · 468 SEK
ASTM F2105
Standard · ASTM ASTM F2105

Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems

1.1 This test method covers procedures for determining air performance characteristics of series universal motor/fan systems used in commercial and household upright, canister, stick, hand-held uti...

Språk

Publicerad

2012-02-24
PDF · 611 SEK
ASTM D1896/D1896M
Standard · ASTM ASTM D1896/D1896M

Standard Practice for Transfer Molding Test Specimens of Thermosetting Compounds

1.1 This practice covers a general procedure for the transfer molding of mechanical and electrical test specimens of thermosetting molding materials. Note 1—The utility of th

Språk

Publicerad

2010-08-01
PDF · 468 SEK
ASTM D2711
Standard · ASTM ASTM D2711

Standard Test Method for Demulsibility Characteristics of Lubricating Oils

1.1 This test method covers the measurement of the ability of oil and water to separate from each other. It is intended for use in testing medium and high-viscosity lubricating oils. 1.2 The value...

Språk

Publicerad

2011-12-16
PDF · 533 SEK
ASTM D2349
Standard · ASTM ASTM D2349

Standard Test Method for Qualitative Determination of Nature of Solvent Composition in Solvent-Reducible Paints

1.1 This test method covers the determination of the nature of solvent in solvent-reducible house paints containing only hydrocarbon solvents. 1.2 The values stated in SI units are to be regarded...

Språk

Publicerad

2003-01-10
PDF · 468 SEK
ASTM B331
Standard · ASTM ASTM B331

Standard Test Method for Compressibility of Metal Powders in Uniaxial Compaction

1.1 This laboratory test method covers the determination of the compressibility of metal powders and metal powder mixtures as measured by the extent to which a sample can be densified under control...

Språk

Publicerad

2011-03-18
PDF · 468 SEK
ASTM E682
Standard · ASTM ASTM E682

Standard Practice for Liquid Chromatography Terms and Relationships

1.1 This practice deals primarily with the terms and relationships used in liquid column chromatography. However, most of the terms should also apply to other kinds of liquid chromatography, notab...

Språk

Publicerad

2006-09-01
PDF · 533 SEK
ASTM B68/B68M
Standard · ASTM ASTM B68/B68M

Standard Specification for Seamless Copper Tube, Bright Annealed

1.1 This specification establishes the requirements for bright annealed seamless copper tube suitable for use in refrigeration, oil lines, gasoline lines, and so forth, where tube with an interior...

Språk

Publicerad

2011-05-20
PDF · 533 SEK
ASTM E1057
Standard · ASTM ASTM E1057

Standard Practice for Measuring Internal Rate of Return and Adjusted Internal Rate of Return for Investments in Buildings and Building Systems

1.1 This practice covers a procedure for calculating and interpreting the internal rate of return (IRR) and adjusted internal rate of return (AIRR) measures in the evaluation of building designs, s...

Språk

Publicerad

2006-04-01
PDF · 533 SEK
ASTM F1320
Standard · ASTM ASTM F1320

Standard Test Method for Evaluating Thermal Paper Employing a Facsimile Thermal Printer as a Test Instrument

1.1 This test method covers a standardized procedure utilizing the facsimile thermal printer as an imaging device for measuring the performance properties of direct thermal paper. 1.2 This test me...

Språk

Publicerad

2006-06-01
PDF · 468 SEK
Förfina din sökning genom att visa:
...som handlar om:

Ämnesområden (0)

Avbryt

Branscher (0)

Avbryt

Syfte (0)

Avbryt

Material (0)

Avbryt
Visa varukorgen Fortsätt handla 0
Varukorgen Stäng
Annonstext