1.1 This test method covers establishing the moisture-penetration resistance relationships of fine-grained soils as determined by the soil penetrometer. 1.2 The values stated in inch-pound units ar...
2011-04-15
1.1 This practice covers procedures for calibrating and determining performance of an optical discrete airborne particle counter (DAPC) when presented with a challenge aerosol of near-monodisperse ...
1998-06-10
2007-04-01
1.1 This practice covers dimensions in millimetres for standard series refractory brick and shapes of all compositions. 1.2 A standard method for converting all other dimensions of shaped refracto...
2005-12-01
1.1 This consumer safety specification establishes performance requirements, test methods, and labeling requirements to promote the safe use of infant bath seats. Products commonly referred to as ...
2011-10-14
1.1 This specification covers high-carbon bearing-quality steel to be used in the manufacture of anti-friction bearings. 1.2 Supplementary requirements of an optional nature are provided and when d...
2009-10-01
1.1 This test method covers the measurement of the break pattern of shoe upper leather using an arbitrary break scale. This test method does not apply to wet blue. <div c
2008-09-01
1.1 This practice covers guidance and direction to suppliers, recyclers, reclaimers, purchasers, and users in the handling, transportation, and storage of Halon 1301. 1.2 The values stated in inch-...
1.1 This guide covers recommended guidelines and test methods for the selection, specification, and use of stretch wrap films for unitizing, reinforcing, and palletizing for indoor environments. T...
2003-10-01
1.1 This test method covers the determination of methanol, ethanol, tert-butanol, methyl tert-butyl ether (MTBE), ethyl tert-butyl ether (ETBE), <span clas
2007-02-07
1.1 This is a guide to developing fire hazard assessments for upholstered seating furniture, within patient rooms of health care occupancies. As such, it provides methods and contemporary fire saf...
2009-01-01
1.1 This specification defines classification, materials, test requirements, inspection certification, marking and packaging of fittings for use with gasketed mechanical couplings complying to Spec...
1.1 This test method covers the determination of corrosion- preventive properties of greases using grease- lubricated ball bearings under dynamic wet conditions. 1.2 The values stated in SI units ...
2011-09-16
1.1 This test method describes the torsion (or twist) testing of metallic wire. 1.2 The values
2007-11-07
1.1 This specification covers pipe piles with protective fusion-bonded epoxy powder coating applied by the electrostatic spray, flocking, or fluidized bed process. Note 1— This specifica...
2004-09-01
1.1 This specification covers refined gold in cast bar form (Note 1). This specification covers refined gold of Grades 99.5, 99.95, 99.99, and 99.995 in cast bar forms. Other forms of u...
2005-05-01
1.1 This specification covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions ma...
2009-04-15
1.1 This test method covers the determination of iron in the range from 1 to 100 μg. 1.2 This test method is intended to be general for the final steps in the determination of iron and
2009-04-01
1.1 This test method covers the determination of the resistance to abrasion of vulcanized rubber, or other rubber materials that are similar to the standard reference compound, used for the soles a...
2006-03-01
1.1 This specification covers high-gravity glycerin (98.7 weight %, minimum) for use in the manufacture of alkyd and other synthetic resins. This specification covers high-grav...
2007-09-05
1.1 These test methods cover a hot mill method, two oven methods, and a press method for the determination of moisture and other volatile matter content in synthetic rubber. 1.2 Either oven method ...
2009-05-01
1.1 This guide describes the design, selection considerations, and installation procedures for the placement of polyethylene pipe or conduit below ground using maxi-horizontal directional drilling ...
2011-08-25
1.1 This practice describes a method for creating test targets containing varying percentages of area coverage for use in determining the yield of the supplies used by liquid and solid ink jet prin...
1998-12-10
1.1 This practice describes methods of preparing surfaces of new and weathered hot-dip galvanized steel for painting. Hot-dip galvanized steel is produced by the immersion of fabricated or unfabric...
2010-09-17
1.1 This specification covers vacuum-treated alloy steel forgings intended for use as turbine rotor disks and wheels. 1.2 The values stated in either SI units or inch-pound units are to be regarde...
1.1 This test method covers the determination of the vapor pressure of pure liquids, the vapor pressure exerted by mixtures in a closed vessel at 40 ± 5 % ullage, and the initial thermal...
1.1 This specification covers pads of repositionable, colored, note paper. Each sheet has a strip of pressure-sensitive adhesive on the back side. 1.2 The values stated in either SI or inch-pound u...
2007-12-05
1.1 This specification covers steel sheet, produced by the Twin-Roll Cast Process (see Appendix X2) and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths. NoteThis specifica...
2011-05-20
1.1 This practice covers requirements for the validation of empirically derived calibrations (Note 1) such as calibrations derived by Multiple Linear Regression (MLR), Principal Component Regressio...
2010-05-17
1.1 This guide provides guidance for use of selected process wastes as structural fills by listing representative test methods for predicting and evaluating those physical characteristics of waste...
1.1 This test method covers a uniform procedure for radioscopic examination of weldments. Requirements expressed in this test method are intended to control the quality of the radioscopic images an...
2009-07-01