1.1 This guide covers techniques for treating uncertainty in input values to an economic analysis of a building investment project. It also recommends techniques for evaluating the risk that a proj...
2012-02-24
1.1 These test methods cover procedures for testing cellulose acetate. 1.2 The test procedures appear in the following sections:
2004-06-01
1.1 This practice describes techniques for planning, conducting, and analyzing the results of an interlaboratory study of a test method. It is designed to be used in conjunction with Practice <a...
2009-12-15
1.1 This test method is a very stringent procedure for establishing the capability of new and used activated carbon to remove radio-labeled methyl iodide from air and gas streams. The single test ...
2004-04-01
1.1 This standard covers the specific procedures and test conditions that are applicable for exposure of unreinforced polyolefin geomembranes to fluorescent UV radiation and conden
2007-01-11
1.1 This test method covers the evaluation of the static load resistance of an insect screen in its functional position in a window under load conditions prescribed by appropriate specifying author...
2009-11-01
1.1 This guide is intended to assist remedial project teams, specifically ecological risk assessors, in identifying data and information options that may be used to perform a screening or complex e...
2004-08-01
1.1 This specification covers an electrical insulating tape for use at low temperature down to approximately −18 °C (0 °F). The tape This specification covers the p...
2010-08-20
1.1 This test method provides procedures for determining the ultimate strength of an assembly consisting of stone with mechanical anchor (anchorage). Load is applied, separately, perpendicular to t...
2009-04-01
1.1 This guide covers the application methods for Specification D 2824 Aluminum-Pigmented Asphalt Roof Coatings, Non-Fibered (Type I), Asbestos Fibered (Type II), and Fibered without Asbestos (Type...
2009-07-01
1.1 This section describes guidelines for microscopical examinations employed in forensic fiber characterization, identification, and comparison. Several types of light microscopes are used, includ...
2010-11-19
1.1 This test method covers the analysis for commonly determined trace metals in test specimens of raw and calcined petroleum coke by inductively coupled plasma atomic emission spectroscopy. 1.2 El...
2009-10-01
1.1 This test method describes the procedures for determining the mass concentration of particulate matter in gaseous streams using an automated, in-stack test method. This method, an in-situ, iner...
1.1 This test method covers the determination of the practical adhesion strength and mechanical failure modes of hard (Vickers Hardness HV = 5 GPa or higher), thin (≤30 μ</spa
2005-06-01
1.1 This practice covers procedures for sampling geosynthetic clay liners (GCLs) for the purpose of laboratory testing. These procedures are designed to ensure that representative samples are obtai...
1.1 This specification covers the composition, dimensions, and physical properties of compression-resistant, perpendicularly oriented mineral fiber (rock, slag, or glass) roll and sheet insulation ...
2011-08-25
1.1 This test method evaluates the energy consumption and cooking performance of deck ovens. The food service operator can use this evaluation to select a deck oven and understand its energy consum...
2005-10-01
1.1 This test method is intended to provide a numerical rating system for classification of resilient floors during the various stages of their wear life in relation to their condition, as perceive...
2011-05-20
1.1 This test method specifies the apparatus and procedure for determining total heat of hydration of hydraulic cementitious materials at test ages up to 7 days by isothermal conduction calorimetry...
2009-12-01
1.1 This specification covers various grades of anhydrous calcined gypsum known as gypsum Keene's cement, designed for use in the base and finish coats of gypsum plaster. Note 1&# This speci...
2006-05-01
1.1 This specification, to be used in conjunction with Specification F1073, c This specification covers the principal shapes and dimensions, and mechanical requirements for the manufacture of two t...
2004-11-01
1.1 This specification covers cold applied, single component, chemically curing silicone sealants that are based on polymers of polysiloxane structures and are intended for use in sealing joints an...
2010-06-01
1.1 This performance specification covers the performance requirements for knitted upholstery fabrics as used in the manufacture of new indoor furniture for general domestic use. These requirement...
2009-09-01
1.1 The purpose of this classification is to provide a method to calculate single-number ratings that can be used for assesing the isolation for the outdoor sound provided by a building or comparin...
2011-03-18
1.1 This classification and subsequent line callout (specification) cover styrenic block copolymer thermoplastic elastomer materials for injection molding and extrusion. Copolymers consist of polys...
2000-11-10
2008-07-07
1.1 This test method is applicable to air-dry architectural coatings of any type, both solvent and water-borne, and of any color, dark as well as light. It cannot be used with films that are dissol...
1.1 This specification covers volumetric flasks and four types of centrifuge tubes, widely used in microchemistry. This specification covers microvolumetric glass vessels (volumetric fla...
2002-10-10
1.1 This test method covers a procedure for the qualitative evaluation of aggregate size and aggregate size distribution of powdered rubber accelerators and other compounding materials which are in...
1.1 These test methods cover the determination of lead, zinc, copper, and manganese in raw rubber and rubber compounds, vulcanized or unvulcanized. The level at which the metals are present is take...
1.1 These test methods cover determining if an adjuvant meets the definitions of an acidifier, a basic blend, alkalinity agent, or buffer in Terminology E1