1.1 This test method is used to measure the vertical flame resistance of textiles. 1.1.1 As a part of the meaure of flame resistance, afterflame and afterglow characteristics are evaluated. 1.2 Thi...
2010-09-17
2008-05-07
1.1 This specification covers Type 58 borosilicate sealing glass for use in electronic applications. Note 1—This specification is primarily intended to consider glass as most This speci...
2005-09-01
1.1 This specification covers an iron-nickel-cobalt alloy, UNS K94610 containing nominally 29 % nickel, 17 % cobalt, and 53 % iron, in the forms of wire, rod, bar, strip, sheet, and tubing, i...
2009-12-01
1.1 This test method applies for the determination of trace uranium content in waste water. It covers concentrations of U between 0.05 mg/L and 2 mg/L. 1.2 The values stated in SI units are to be r...
2004-06-01
1.1 This test method describes the calculation of true vapor pressures of petroleum distillate fuels for which distillation data may be obtained in accordance with Test Method <a href="http://my...
2005-11-01
1.1 This test method covers the measurement of Krebs Unit (KU) viscosity to evaluate the consistency of paints and related coatings using the Stormer-type viscometer. 1.2 The values stated in SI ...
1.1 This test method for toughness of wood-based structural panels covers the determination of energy necessary to cause failure by impact loading of a beam specimen which is simply supported and l...
2011-09-16
1.1 This practice covers the determination of the temperature at which a dry toner will cake as storage temperatures are raised. 1.2 In certain cases the effects of pressure or pressure combined wi...
1989-10-27
1.1 This test method covers the measurement of soluble, suspended, and total radium-226 in water in concentrations above 3.7 × 10−3 Bq/L. This test method is
2011-12-16
1.1 This test method covers the measurement of the rate of vapor transmission of volatile liquids through a rubber sheet, disk, or diaphragm. 1.2 The values stated in SI units are to be regarded as...
2005-05-01
1.1 This test method covers the determination of the volume resistivity of resin-based conductive adhesives in the cured condition. The test is made on a thin adhesive layer as prepared in a bonded...
2004-04-01
1.1 This practice covers a procedure for adjusting the operational sensitivity of in-plant walk-through metal detectors. Performance of this procedure should result with in-plant walk-through meta...
1997-12-10
1.1 This specification covers filament-reinforced, pressure-sensitive adhesive tape. 1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values sta...
2007-01-11
1.1 This test method covers the determination of the extrudability of unvulcanized SBR and NBR rubber compounds through a screw-type extruder equipped with ASTM Extrusion Die, Garvey type. This te...
2007-09-05
1.1 This specification covers bare hard-drawn round copper-clad steel wire for electrical purposes (Note 1). Note 1—Wire ordered to this specification is not intended for This specifica...
2010-08-20
1.1 This test method covers procedures for measuring reaction rates by the activation reaction
2008-11-05
1.1 This practice covers the requirements for the apparatus and equipment used to prepare specimens for the determination of length change in hardened cement paste, mortar, and concrete, the appar...
2011-11-18
1.1 This practice covers the procedures for calibration of linear displacement sensors and their corresponding power supply, signal conditioner, and data acquisition systems (linear displacement se...
2007-02-07
1.1 This practice covers analytical and analytical-experimental approaches that can be used to determine the variation in neutron exposure (fluence E > 1.0 MeV, dpa, etc.) and exposure rate and ...
2001-06-10
2009-04-01
1.1 These test methods establish a recommended list from which suitable test methods shall be selected for the identification of physical property characteristics and comparison of the performance ...
2009-07-01
1.1 This practice covers the detection and identification by thin-layer chromatography of antidegradants (antioxidants, antiozonants, and stabilizers) that may be present in raw rubber or rubber pr...
2005-12-01
1.1 This test method covers the determination of the resistance of all types of zippers to corrosion and their ability to function properly after exposure of specified duration in a prescribed salt...
1.1 This test method is applicable for the determination of particulate matter emissions from solid-fuel-burning appliances including woodstoves, pellet-burning appliances, factory-built fireplaces...
2012-02-24
1.1 This test method covers the procedure to determine the mass of deposit formed on a specially constructed test rod exposed to repetitive passage of 8.5 g of engine oil over the rod in a thin fil...
2009-06-01
1.1 This test method covers the determination of the time from the initial mixing of the reactants of a thermosetting plastic composition to the time when solidification commences, under conditions...
1999-11-10
2008-09-24
1.1 This practice covers the materials, processes, and quality controls to be used in the manufacture of adhesive-bonded, aluminum-faced, foam core sandwich panels for tactical shelters. 1.2 The v...
2009-11-01
1.1 This specification covers materials, dimensions, and workmanship, and performance tests for medium-density and high-density smooth-wall coilable polyethylene (PE) conduit (duct) containing elec...
2002-03-10
2011-07-12
1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar. The classifications of concrete and mort...
2011-05-20
1.1 This guide covers conducting and evaluating galvanic corrosion tests to characterize the behavior of two dissimilar metals in electrical contact in an electrolyte under low-flow conditions. It ...
2003-10-01
1.1 This practice covers the procedures to be followed in the preparation (by abrasive blast cleaning) of hot rolled steel panels for laboratory testing of coatings. 1.2 This standard practice does...