1.1 This procedure describes a method of measuring the dynamic stiffness (DS) and cylindrical coefficient of restitution (CCOR) of baseballs and softballs providing similar impact forces and ball d...
2011-05-20
1.1 This specification covers the requirements for wrought 18chromium-14nickel-2.5molybdenum stainless steel tubing used for the manufacture of surgical implants. Material shall conform to the appl...
2009-02-01
1.1 This test method covers the ability of a grease to adhere to a metal surface when subjected to a water spray under prescribed laboratory conditions. 1.2 The values stated in SI units are to be...
2006-11-01
1.1 This practice covers the calibration and use of torque meters of the type normally used in packaging applications. 1.2 This standard does not purport to address all of the safety concerns, if any
2007-12-05
1.1 This test method covers the quantitative determination of total sulfur in gasoline and gasoline-oxygenate blends. The Pooled Limit of Quantitation (PLOQ) was determined to be 1
2013-01-18
1.1 This specification covers non-asbestos fiber-cement conduit for use in electric-power systems and communication systems. The service is for both underground and exposed conditions. 1.2 The valu...
2005-04-05
1.1 This test method covers the determination of bulk density of a representative 2-kg sample of calcined petroleum coke, after vibration to increase compaction. 1.2 The procedure is limited to par...
2010-09-17
1.1 This practice covers procedures for testing the joints of installed precast concrete pipe sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joi...
2003-11-01
1.1 This standard defines the specialized terms used in standards developed by Committee F23 on Protective Clothing. 1.2 Definitions of Terms, which were drafted for use only in a single standard, ...
2003-07-10
1.1 This practice covers a procedure for determining the amount of coating applied to a substrate, (for example, film, paper, nonwoven). The amount of coating is expressed as a wei
2007-09-05
1.1 This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dime...
2003-08-10
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded shapes of rods and bars made from poly(vinyl chloride) (PVC...
1.1These test methods cover the determination of reducible sulfur in paper and paperboard within the context of the given definitions. 1.1.1Method A—The quantitative method gives a m
1997-12-10
2010-08-01
1.1 This practice covers the design, manufacture, and operation of inflatable amusement devices and their associated operating environments. 1.2 This practice specifically excludes inflatable devic...
2010-02-01
1.1 This specification covers geocomposite drainage panels used in highway, turf, and other high volume subsurface drainage applications. These products consist of a geotextile wrapped around a pol...
2006-01-01
1.1 This certification of coating conformance form provides procurement information concerning products being furnished in accordance with a specific coating specification and additional This guide...
2004-06-01
1.1 This test method determines the lethality (LD50 value, slope and 95% confidence interval (CI)) and signs of acute toxicity from a material using a limited number of rats. The technique used in ...
2011-09-16
1.1 This guide covers the major variables which affect the rate of arc erosion of electrical contact materials and serves as a guide in developing more detailed specifications for arc-erosion test...
2005-11-01
1.1 These test methods cover the determination of barium, calcium, phosphorus, sulfur, and zinc in unused lubricating oils at element concentration ranges shown in Table 1. The range can be extende...
1.1 This test method covers a procedure for determining the effect of impact loading on the bonding of sprayed fire-resistive material (SFRM) applied to the underside of steel floor deck. These ma...
2005-05-01
1.1 These test methods cover the determination of acid value and amine value in fatty quaternary ammonium chlorides. 1.2 This standard does not purport to address all of the safety problems, if ...
1992-01-01
2007-03-20
1.1 This test method covers quantitative methods for the sampling and determination of bacterial endotoxin concentrations in water miscible metalworking fluids (MWF). 1.2 Users of this test method ...
2012-02-24
1.1 This specification covers ductile iron castings for pressure-retaining parts for use at elevated temperatures. Castings of all grades are suitable for use up to 450°F. For temperatu...
2009-05-01
1.1 This practice describes the recommended procedure for installing inductive loop detectors in sawed slots in roadway pavement for use as a traffic monitoring device or to actuat
1.1 This classification system provides a method of adequately identifying PTFE micropowders using a system consistent with that of Classification System D This classification system provides a met...
2004-02-01
1.1 This practice serves as a guide for using the information obtained as directed in Practice D 2904 or obtained by other statistical techniques from other distributions, to prepare statements on ...
1997-11-10
2008-08-08
1.1 This test method covers the evaluation of the performance of lubricating greases in ball bearings operating under light loads at high speeds and elevated temperatures. 1.2 The values stated in...
1.1 This test method establishes procedures for determining the effect of random vibration, within the specified frequency range, on switch contacts, mounting hardware, adhered component parts, sol...
2002-05-10
1.1 These test methods cover testing procedures that estimate the ability of soft rubber materials to resist dynamic fatigue. No exact correlation between these test results and service is given or...
2006-05-01
1.1 This specification2 covers minimum-wall-thickness, seamless carbon steel boiler and super This guide covers standard specifications for minimum-wall-thickness, seamless carbon steel ...
2002-01-01