1.1 This test method covers a procedure for obtaining the data which are used to calculate the shrinkage limit and the shrinkage ratio.1.2 This test method uses mercury which is a hazardous substan...
2004-02-01
2008-03-31
1.1 This specification covers the construction of steel furniture drawers for use where invoked by other marine furniture specifications. 1.2 This specification applies to all furniture drawers, ...
2004-11-01
1.1 This laboratory practice is designed to evaluate the utility and effectiveness of antimicrobial agents intended to control microbial growth in invert emulsions and other water containing hydrau...
2009-04-01
1.1 This specification covers nickel-iron-chromium-molybdenum-columbium stabilized alloy (UNS N08700)* bar. This specification covers nickel-iron-chromium-molybdenum-columbium stabilize...
2002-10-10
1.1 These test methods describe procedures for determining the presence of cuprous oxide (Cu2O) in products made from deoxidized and oxygen-free copper.
2010-05-01
1.1 This practice covers techniques that are of general use in analyzing qualitatively multicomponent samples by using a combination of gas chromatography (GC) and infrared (IR) spectrophotometric...
2005-09-01
1.1 This practice covers procedures for testing and locating the sources of gas leaking at the rate of 1 × 10−8 Pa m3/s (1 &
2011-09-16
1.1 This test method evaluates the energy consumption and cooking performance of deck ovens. The food service operator can use this evaluation to select a deck oven and understand its energy consum...
2005-10-01
-
2005-05-01
1.1 This practice is intended to assist in the selection of sorbents and procedures for the sampling and analysis of ambient (1) , indoor (2) and workplace (3, 4)
2003-05-10
1.1 This specification covers material requirements for unfabricated and fabricated forms of hydrated calcium sulfate intended for surgical implants. Fabricated forms may include pressed and cast ...
2009-09-01
1.1 These test methods cover two procedures for measuring the consistency of small samples of lubricating greases by penetration of a ¼-scale cone or a ½-scale cone. Th
2010-09-17
1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operating performance characteristics and the performance characteristics under assault c...
2005-02-01
1.1 This test method covers the procedure for the measurement of the Superpave Gyratory Compactor (SGC) internal angle of gyration using an instrument capable of simulating loading conditions simil...
1.1 This guide covers design and construction criteria for striker plates and sounding tubes, excluding deck penetrations and caps, for use with sounding rods or tapes in freshwater, saltwater, an...
2004-05-01
1.1 This test method covers the determination of the purity of certain commercially available aldehydes and ketones. <a nam
2006-06-01
1.1 This practice is intended as an aid to electroplaters in setting up a suitable cleaning cycle preparatory to electroplating of low-carbon steel (Note 1) containing less than 0.35 mass % of carb...
1.1 This guide describes materials and procedures which may be used to clean dimension stone exteriors as well as the conditions under which they may be used. It is intended to aid owners, maintena...
2011-12-16
1.1 This test method covers the determination of the contact bounce time of a membrane switch. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are in...
2009-06-15
1.1 The purpose of this test method is to define a method for analyzing the surface texture of the above-mentioned components using a scanning tunneling microscope (STM). STM is a
1999-06-10
1.1 This practice is applicable to a wide range of virgin pulps or pulps derived from recovered materials or recovered paper of the type typically used to produce paper, paperboard and other paper ...
2007-12-01
2010-08-01
1.1 This practice describes a method for ultrasonic mapping of the soundness of a bond joining a sputtering target to its supporting backing plate. The results of the examination may be used in pre...
1999-12-10
1.1 This guide covers guidelines for the acceptance testing requirements for geosynthetic clay liner (GCL) materials, describing types of tests, test methods, and recommended verifications. 1.2 Thi...
2009-06-01
1.1 This guide covers: 1.1.1 Defining a document structure for use by electronic signature mechanisms
1.1 This test method covers the determination, by direct measurement, of the ambient to 260°C [500°F] volatile distillate fraction of cold mix asphalt mixtures. <p
1.1 These test methods cover four options for measuring fabric length and are applicable to full rolls or bolts of materials. 1.2 There are four approved options of measuring length as follows: 1.2...
2011-05-20
1.1 This test method covers the titrimetric determination of zirconium in zirconium driers used in the coatings industry and utilizes the disodium salt of ethylenediaminetetraaceti
1.1 This specification covers modular gauge boards for mounting 89-mm (3½ -in.), 114-mm (4½-in.), 152-mm (6-in.), and 216-mm (8½ -in This specification covers modul...
2006-02-01
1.1 These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. <a name="
2007-09-05
1.1 This test method covers the use of magnetic instruments for the nondestructive measurement of the thickness of an electrodeposited nickel coating on either a magnetic or nonmagnetic substrate....
2009-04-15