1.1 This guide covers suggested components of the documentation of a groundwater modeling code. Documentation of a groundwater modeling code consists of textual and graphical information recorded d...
2004-05-01
1.1 This practice covers a method for exposing specimens of colored art materials indoors to sunlight coming through a closed window. Any color change is compared to fading in a Blue Wool Reference...
2003-05-10
1.1 This guide is used as a discussion of the relevancy of several methods to obtain the vapor transmission of geomembranes. 1.2 This guide discusses applicable test methods, test materials and c...
2008-03-12
1.1 This test method covers a procedure, using the microprojector, for the counting of partial cleavages in wool and other animal fibers. 1.2 The values stated in SI units are to be regarded as st...
2005-09-01
1.1 This specification covers zinc-coated low-carbon steel wire for use in armoring for protection against damage of submarine and underground cables used for communication, contro This ...
2008-05-01
1.1 This guide covers procedures for reducing the susceptibility in some steels to hydrogen embrittlement or degradation that may arise in the finishing processes. 1.2 The heat treatment procedures...
2004-04-01
1.1 This practice covers the use of gas chromatography and mass spectrometry to analyze and compare petroleum oil spills and suspected sources. <div class="SectionLevel2"
2006-08-15
1.1 These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods inclu...
2007-09-05
1.1 This test method covers the determination of the vapor pressure of pure liquids, the vapor pressure exerted by mixtures in a closed vessel at 40 ± 5 % ullage, and the initial thermal...
2011-04-15
1.1 This fire-test-response standard covers the measurement of the relative fire characteristics of roof coverings under simulated fire originating outside the building. It is applicable to roof c...
2011-11-18
1.1 This specification covers solid, dry-cast, concrete building brick intended for interior and exterior use in constructing structural masonry, and are made from portland cement, water, and s...
2011-08-25
1.1 This specification covers ACuZinc5, a commercial zinc-copper-aluminum alloy (Z46540), in ingot form for remelting for use in the production of castings. 1.2 The values stated in inch-pound uni...
2010-05-17
1.1 This specification covers ductile iron castings that are subsequently heat treated by an austempering process as defined in 10.1. 1.2 The application of the austempering heat treatment extends ...
2006-02-01
1.1 This specification covers the requirements for quenched and tempered alloy steel socket-set screws (SSS) 0.060 through 2.000-in. sizes having hardnesses 45 to 53 HRC.1.2 These set screws are in...
2012-02-24
1.1 This test method determines the brightness of white, near-white, and naturally colored pulp, paper, and paperboard. Brightness is a commonly used industry term for the numerical value of the re...
1997-12-10
2010-05-01
1.1 This test method is intended to define conditions for the exposure of coated pipe to weather. 1.2&
2004-11-01
1.1 This test method covers the determination of the creep behavior of cylindrical specimens of frozen soil, subjected to uniaxial compression. It specifies the apparatus, instrumentation, and proc...
1.1 This test method covers the determination of the micronaire reading of loose cotton fibers by measuring the resistance of a specific mass (plug) of cotton fibers to air flow under prescribed c...
2011-05-20
1.1 This practice describes procedures to estimate Thurstonian discriminal distances (that is, d' values) from data obtained on two samples. Procedures are presented for four forced-choice methods ...
2003-07-10
1.1 This test method covers the determination of the ignition loss of cured reinforced resins. This ignition loss can be considered to be the resin content within the limitations of 4.2. 1.2 The va...
2011-12-16
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems. 1.2 This test method addresses equipment used in hunting s...
2011-09-16
-
2010-03-01
1.1 Purpose and Application: 1.1.1 This guide covers the equipment, field procedures, and interpretation methods for the assessment of subsurface materials using the im
1.1 This specification covers requirements for glass volumetric flasks of precision and general-purpose grades suitable for laboratory purposes. 1.1.1 Class A—
1.1 This test method covers the determination of total oxygen demand in the range from 100 to 100 000 mg/L, in water and wastewater including brackish waters and brines (see 6.5). Larger concentrat...
1998-03-10
1.1 This test method defines a method for determining bat performance by measuring the bat-ball coefficient of restitution (BBCOR), deriving the bat performance factor (BPF), and calculating batted...
1.1 This specification covers hot-mixed, hot-laid asphalt, tar, emulsified asphalt, and recycled bituminous paving mixtures for base, binder, leveling, and surface courses. 1.2 The values stated...
2001-06-10
2009-06-01
1.1 All microscopes are subject to artifacts. The purpose of this document is to provide a description of commonly observed artifacts in scanning tunneling microscopy (STM) and ato
2004-08-01
1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elast...
1.1 This specification covers spray-formed seamless austenitic stainless steel pipe intended for high-temperature and general corrosive service. 1.2 Grades TP304H, TP309H, TP309HCb, TP310H, TP310...
2009-10-01