1.1 This test method covers paper and paper products that have been treated or designed to resist penetration by oils or greases commonly found in foodstuffs. Such papers include but are not limite...
2008-02-06
2010-02-01
1.1 Purpose: 1.1.1 The purpose of this test method, as a part of a suite of mobility test methods, is to quantitatively evaluate a teleoperated ground robot<span
2012-02-24
1.1 This guide covers electronic instruments intended for measurement of temperature by detecting intensity of thermal radiation exchanged between the subject of measurement and the sensor. 1.2 The...
2010-05-01
1.1 This environmental chamber method measures the resistance of the treated wet blue to the germination of spores and subsequent vegetative growth over a period of four weeks. The test method is u...
1.1 This terminology includes terms, definitions of terms, descriptions of terms, nomenclature, and acronyms associated with coordinate systems and testing methodologies for additive manufacturing ...
1.1 This practice describes minimum data required to locate and identify a postmining land use for a surface coal mining and reclamation operation. Statutory language and definitions are found in F...
2010-05-15
1.1 This guide covers the procedures for evaluating and preparing non-aggregate surfaced membranes for the application of a coating. It does not address design, construction, or installation issues...
2010-09-17
1.1 This guide covers practical techniques for condition data trend analysis. 1.2 The techniques may be utilized for all instrumentation that provides numerical test results. This guide is written ...
2011-05-20
1.1 Purpose: 1.1.1 The purpose of this test method is to quantitatively evaluate a teleoperated ground robot’s (see Terminology <a h
1.1 This practice identifies and describes equipage and procedures for safely handling unmanned aircraft forced to recover at alternate or diversionary airfields where personnel trained in recoveri...
2010-06-15
1.1 The Behind-the-Knee (BTK) method, using the popliteal fossa of human volunteers as a test site, simultaneously evaluates the inherent chemical irritation, and the potential for mechanical irrit...
1.1 This specification covers the retained sewn seam strength of flame resistant fabric subassemblies after repeated short duration exposures to hot air or repeated short-duration exposures to ho...
1.1 This guide provides recommended minimum requirements for various types of fences for non-residential outdoor swimming pools, hot tubs and spas. 1.2 The various types of fences may be chain link...
2010-04-01
1.1 This specification describes a data file exchange format for three-dimensional (3D) imaging data, known as the ASTM E57 3D file format, Version 1.0. The term “E57 file”T...
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 1—Fastener ductility information is presented in Table 2 and This specificat...
1.1 This test method describes the calibration or performance confirmation of the electronic pressure signals from thermal analysis apparatus. 1.2 The values stated in SI units are to be regarded a...
1.1 This practice sets forth minimum criteria and evaluation requirements for products employing the use of different systems to trace wood fiber to sources operating under different forest managem...
1.1 This test method describes a means to determine the percentage of processing, potential, and total volatiles from radiation curable acrylate monomers, oligomers, and blends. The results can be ...
1.1 This specification covers polyolefin chopped strands (fibers) for use in concrete. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The va...
2010-06-01
1.1 This laboratory practice covers the quantitative determination of surface deposits produced during the thermal oxidation of gas turbine fuels by monitoring the oscillation frequency of a quartz...
1.1 This practice provides the procedure for using the impulse-response method to evaluate rapidly the condition of concrete slabs, pavements, bridge decks, walls, or other plate-like structures. 1...
2010-12-15
1.1 This test method covers the determination of the permeability of a PM bearing when subjected to pressurized nitrogen under controlled conditions. 1.2 The values stated in SI units are to be reg...
1.1 This guide provides a compendium of information and a menu of options for assessment of fungal growth in buildings, but does not recommend a specific course of action. Due to the wide variety o...
2010-12-01
1.1 This practice covers and provides instructions on making a volumetric blend of denatured fuel ethanol with gasoline blendstocks, such as a reformulated gasoline blendstock for oxygenate blendin...
1.1 This test method is designed to evaluate decontamination methods (physical, chemical, self-decontaminating materials) when used on surfaces contaminated with virus-containing droplets. 1.2 This...
2010-10-01
1.1 This test method covers the determination of distribution coefficients of chemical species to quantify uptake onto solid materials by a batch sorption technique. It is a laboratory method prima...
1.1 This test method covers monitoring nitration in gasoline and natural gas engine oils as well as in other types of lubricants where nitration by-products may form due to the combustion proces...
2010-08-01
1.1 This practice covers the minimum elements for the accurate location and description of geospatial data for defining Abandoned Mine Land (AML) Problem Areas, Planning Units, Keyword Features, an...
1.1 This guide covers the FT-IR fingerprinting of a liquid paint as supplied in the container without the need to separate components. Spectra collected using this technique have been found useful ...