1.1 This terminology defines the terminology used in test methods, specifications, guides, and practices related to bioremediation technology.
2007-09-05
1.1 This specification covers an ozone-resistant insulating compound for electrical wire and cables 14 AWG and larger. This compound consists substantially of a thermoplastic elastomer. 1.2 This t...
2002-03-10
1.1 This practice guides the user in selection of procedures commonly used to measure depth in water bodies that are as follows:
1.1 This test method provides for determining the release rates of heat and visible smoke (Note 1) from materials, products, or assemblies when exposed to different levels of radiant heat. <sp...
2010-04-15
1.1 This specification covers requirements for glass measuring pipets of precision and general purpose grades, used in measuring volumes of liquids. This specification covers requirements of precis...
2002-10-10
1.1 This terminology covers definitions of technical terms used in the rubber industry. Terms that are generally understood or adequately defined in other readily available sources are not include...
2012-02-24
1.1 This specification establishes performance requirements of surge suppressors for use on shipboard ac power circuits. 1.2 Surge suppressor shall be a protective device for limiting voltage trans...
2006-02-01
1.1 This practice covers two levels of tests to measure the performance of laboratory Fourier transform near infrared (FT-NIR) spectrometers. This practice applies to the short-wave near
1998-03-10
1.1 This test method provides a screening test for determining the amount of metal loss from plates and screws used for osteosynthesis (internal fixation of broken bones) due to fr
2002-12-10
1.1 These test methods cover the sampling and chemical analysis of solid natural rubber in the forms supplied to the rubber industry. 1.2 The analytical procedures appear in the following order:<...
1.1 This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 to 30 % volume by means of the centrifuge procedure. Note 1
2011-09-16
1.1 This test method covers the determination of the stiffness of fabrics by the circular bend procedure. 1.2 This test method is generally applicable to all types of fabrics, including woven, knit...
2008-11-05
1.1 This practice establishes the general requirements with which a reference materials (RM) producer has to demonstrate that it operates, if it is to be recognized as competent to produce RMs used...
1.1 This specification covers cutback petroleum asphalts of the medium-curing type for use in the construction and treatment of pavements. 1.2 The values stated in SI units or inch-pounds are to b...
2010-06-01
1.1 This practice covers the preservation of waterborne oil samples from the time of collection to the time of analysis. Information is provided to ensure sample integrity and to a This ...
1990-05-25
1.1 These test methods cover tests for hot-applied types of joint and crack sealants and fillers for portland cement concrete and asphaltic concrete pavements. There are numerous standard materia...
2009-06-01
1.1 This test method covers the determination of sulfur in aromatic hydrocarbons, their derivatives, and related chemicals. 1.2 This test method is applicable to samples with sulfur ...
1.1 This practice covers reporting particle size measurement data. 1.2 This practice applies to particle size measurement methods, devices, detail levels, and data formats for dry powders, and wet ...
2009-03-01
1.1 This specification covers solid, dry-cast, concrete building brick intended for interior and exterior use in constructing structural masonry, and are made from portland cement, water, and s...
2011-08-25
1.1 This practice has been prepared for use by the designer, specifier, and applicator of IRCCS (Interior Radiation Control Coating Systems) for use in building construction. The scope is limited ...
2009-11-01
1.1 This specification covers the chemical, mechanical, and metallurgical requirements for wrought titanium-15 molybdenum alloy to be used in the manufacture of surgical implants (1). 1.2 The valu...
1.1 This test method covers the determination of the effects of selected environments on aggregates for use in manufacturing sulfur polymer cement concrete (SC) and other chemical-r
2005-04-01
1.1 This guide covers the key factors to consider in estimating the effectiveness of containment and recovery systems that may be used to assist in the control of oil spills on water. 1.2 The purpo...
1.1 This test method is used for determining the strength loss or reduction in continuity, or both, of prism-shaped specimens which are cut from refractory brick or shapes and subjected to thermal ...
2005-05-01
1.1 This test method establishes the classification and testing of cord as a component material used in the fashioning of bowstrings. 1.2 This test method is not intended to provide information bey...
2006-05-01
1.1 This standard describes three test methods2 for determining the modulus of elasticity in
2008-12-01
1.1 These test methods cover two procedures for measuring the thickness of diffusion coatings. 1.2 Test Method A is the determination of the dimensional-change thickness, defined as the difference ...
2010-06-18
1.1 This specification covers minimum physical and chemical quality requirements or specifications for five grades of raw natural rubber. This specification covers the minimum physical and chemica...
1.1 This specification covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter, in the tempers shown in This specification covers aluminium 1350 drawin...
1997-03-10
1.1 This specification covers 75 % gold-22 % silver-3 % nickel alloy tubing, rod, wire, strip, and sheet material for sliding electrical contacts. This specification c...
2008-05-01