21298 träffar på

Standard · ASTM ASTM D6150 Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility 1.1 This test method describes a procedure for the determination of the relative volatility of polyvinyl chloride plastisols and organosols at elevated temperatures.1.2 The values stated in SI unit... Språk Publicerad 2003-07-10 Upphävd 2009-09-01

PDF · 468 SEK

Standard · ASTM ASTM D6122 Standard Practice for Validation of the Performance of Multivariate Process Infrared Spectrophotometers 1.1 This practice covers requirements for the validation of measurements made by online, process near- or mid-infrared analyzers, or both, used in the calculation of physical, chemical, or quality ... Språk Publicerad 2006-07-01 Upphävd 2009-06-01

PDF · 767 SEK

Standard · ASTM ASTM D6113 Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical o... 1.1 This is a fire-test-response standard.1.2 Several fire-test-response characteristics, including the time to sustained flaming, heat release rate, total heat released, effective heat of combusti... Språk Publicerad 2003-03-10 Upphävd 2009-07-01

PDF · 611 SEK

Standard · ASTM ASTM D6111 Standard Test Method for Bulk Density and Specific Gravity of Plastic Lumber and Shapes by Displacement 1.1 This test method covers the determination of the bulk density and specific gravity of plastic lumber and shapes in their "as manufactured" form. As such, this is a test method for evaluating th... Språk Publicerad 2003-03-10 Upphävd 2009-09-01

PDF · 533 SEK

Standard · ASTM ASTM D6108 Standard Test Method for Compressive Properties of Plastic Lumber and Shapes 1.1 This test method covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of st... Språk Publicerad 2003-03-10 Upphävd 2009-09-01

PDF · 533 SEK

Standard · ASTM ASTM D6050 Standard Test Method for Determination of Insoluble Solids in Organic Liquid Hazardous Waste 1.1 This test method covers the determination of the approximate amount of insoluble, suspended solid material in organic liquid hazardous waste (OLHW). 1.2 This test method is intended to be use... Språk Publicerad 2003-03-10 Upphävd 2009-02-01

PDF · 468 SEK

Standard · ASTM ASTM D6042 Standard Test Method for Determination of Phenolic Antioxidants and Erucamide Slip Additives in Polypropylene Homopolymer Formulations Using Liquid... 1.1 This test method covers a liquid-chromatographic procedure for the separation of some additives currently used in polypropylene. These additives are extracted with a cyclohexane:methylene chlor... Språk Publicerad 2004-07-01 Upphävd 2009-09-01

PDF · 533 SEK

Standard · ASTM ASTM D5991 Standard Practice for Separation and Identification of Poly(Vinyl Chloride) (PVC) Contamination in Poly(Ethylene Terephthalate) (PET) Flake 1.1 This practice covers four procedures for separation and qualitative identification of poly(vinyl chloride) (PVC) contamination in poly(ethylene terephthalate) (PET) flakes. Note 1—Alt... Språk Publicerad 1996-07-10 Upphävd 2009-02-01

PDF · 468 SEK

Standard · ASTM ASTM D5946 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements 1.1 This test method covers measurement of the contact angle of water droplets on corona-treated polymer film surfaces. Note 1—There is no similar or equivalent ISO standard. 1.2 The valu... Språk Publicerad 2004-02-01 Upphävd 2009-04-01

PDF · 533 SEK

Standard · ASTM ASTM D5930 Standard Test Method for Thermal Conductivity of Plastics by Means of a Transient Line-Source Technique - Språk Publicerad 2001-01-01 Upphävd 2009-08-15

PDF · 533 SEK

Standard · ASTM ASTM D5926 Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems 1.1 This specification describes material and physical requirements for nonrigid poly (vinyl chloride) (PVC) preformed molded and spliced gaskets used in mechanical couplings. These couplings are u... Språk Publicerad 2004-10-01 Upphävd 2009-09-01

PDF · 468 SEK

Standard · ASTM ASTM D5907 Standard Test Method for Filterable and Nonfilterable Matter in Water 1.1 This test method covers the determination of filterable and nonfilterable matter in drinking, surface, and saline waters, domestic and industrial wastes. The practical range of the determinatio... Språk Publicerad 2003-06-10 Upphävd 2009-09-01

PDF · 533 SEK

Standard · ASTM ASTM D5857 Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology 1.1 This specification covers polypropylene materials suitable for injection molding and extrusion. Polymers consist of polypropylene homopolymers, polypropylene copolymers, and polypropylene-elast... Språk Publicerad 2008-12-03 Upphävd 2009-09-01

PDF · 767 SEK

Standard · ASTM ASTM D5853 Standard Test Method for Pour Point of Crude Oils 1.1 This test method covers two procedures for the determination of the pour point temperatures of crude oils down to -36°C. Procedure A provides a measure of the maximum (upper) pour poin... Språk Publicerad 2006-07-01 Upphävd 2009-04-15

PDF · 533 SEK

Standard · ASTM ASTM D5831 Standard Test Method for Screening Fuels in Soils 1.1 This test method is a screening procedure for determining the presence of fuels containing aromatic compounds in soils. If the contaminant fuel is available for calibration, the approximate co... Språk Publicerad 2008-02-01 Upphävd 2009-07-01

PDF · 533 SEK

Standard · ASTM ASTM D5740 Standard Guide for Writing Material Standards in the Classification D4000 Format 1.1 This classification system covers____ materials suitable for________________ . The inclusion or exclusion of recycled plastics in this classification system must be addressed here.1.2 The prope... Språk Publicerad 2003-07-10 Upphävd 2009-09-01

PDF · 533 SEK

Standard · ASTM ASTM D5704 Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles 1.1 This test method is commonly referred to as the L-60-1 test. It covers the oil-thickening, insolubles-formation, and deposit-formation characteristics of automotive manual transmission a... Språk Publicerad 2008-10-15 Upphävd 2009-04-15

PDF · 611 SEK

Standard · ASTM ASTM D5681 Standard Terminology for Waste and Waste Management 1.1 This terminology contains standard definitions of terms used in the general area of waste and waste management. It is intended to promote understanding by providing precise technical definition... Språk Publicerad 2008-12-03 Upphävd 2009-07-01

PDF · 611 SEK

Standard · ASTM ASTM D5672 Standard Test Method for Testing Flexible Cellular Materials Measurement of Indentation Force Deflection Using a 25-mm (1-in.) Deflection Technique 1.1 This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.1.2 This test method is ... Språk Publicerad 2003-03-10 Upphävd 2009-09-01

PDF · 468 SEK

Standard · ASTM ASTM D5668 Standard Test Methods for Rubber From Synthetic Sources-Volatile Matter 1.1 This test method covers four test methods: a hot mill method, two oven methods and a press method for the determination of moisture and other volatile matter content in synthetic rubber.1.2 Eit... Språk Publicerad 2003-11-01 Upphävd 2009-05-01

PDF · 468 SEK

Standard · ASTM ASTM D5589 Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Algal Defacement 1.1 This test method covers an accelerated method for determining the relative resistance of a paint or coating film to algal growth. Note 1—It is hoped that a ranking of relative perform... Språk Publicerad 1997-07-10 Upphävd 2009-07-01

PDF · 468 SEK

Standard · ASTM ASTM D5546 Standard Test Method for Solubility of Asphalt Binders in Toluene by Centrifuge 1.1 This test method covers determination of the degree of solubility of asphalt binders in toluene using centrifugal separation. The method is an alternative to Test Method D 2042, and may be pref... Språk Publicerad 2001-12-10 Upphävd 2009-06-01

PDF · 468 SEK

Standard · ASTM ASTM D5516 Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to Elevated Temperatures 1.1 This test method is designed to determine the effect of exposure to high temperatures and humidities on the flexure properties of fire-retardant treated softwood plywood. In this test method, p... Språk Publicerad 2003-04-10 Upphävd 2009-05-15

PDF · 533 SEK

Standard · ASTM ASTM D5501 Standard Test Method for Determination of Ethanol Content of Denatured Fuel Ethanol by Gas Chromatography - Språk Publicerad 2004-01-01 Upphävd 2009-04-15

PDF · 533 SEK

Standard · ASTM ASTM D5485 Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter 1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products.1.2 This test method provides corrosion result... Språk Publicerad 2005-09-01 Upphävd 2009-06-01

PDF · 611 SEK

Standard · ASTM ASTM D5478 Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer 1.1 These test methods cover the measurement of the viscosity of Newtonian and non-Newtonian liquids. These test methods are applicable to liquids having viscosities in the range from 5 ×... Språk Publicerad 2003-12-01 Upphävd 2009-02-01

PDF · 533 SEK

Standard · ASTM ASTM D5434 Standard Guide for Field Logging of Subsurface Explorations of Soil and Rock 1.1 This guide describes the type of information that should be recorded during field subsurface explorations in soil and rock.1.2 This guide is not intended to specify all of the information requi... Språk Publicerad 2003-11-01 Upphävd 2009-05-01

PDF · 468 SEK

Standard · ASTM ASTM D5422 Standard Test Method for Measurement of Properties of Thermoplastic Materials by Screw-Extrusion Capillary Rheometer 1.1 This test method covers the use of a screw-extrusion-type capillary rheometer for the measurement of flow properties of thermoplastics and thermoplastic compounds. The measured flow properties,... Språk Publicerad 2003-04-10 Upphävd 2009-04-01

PDF · 533 SEK

Standard · ASTM ASTM D5340 Standard Test Method for Airport Pavement Condition Index Surveys 1.1 This test method covers the determination of airport pavement condition through visual surveys of asphalt-surfaced pavements, including porous friction courses, and plain or reinforced jointed ... Språk Publicerad 2004-07-01 Upphävd 2009-07-01

PDF · 858 SEK

Standard · ASTM ASTM D5336 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials 1.1 This specification covers polyphthalamide materials suitable for injection molding.1.2 The properties included in this specification are those required to identify the compositions covered. The... Språk Publicerad 2003-11-01 Upphävd 2009-09-01

PDF · 533 SEK

• < Föregående
• 175
• 176
• 177
• 178
• 179
• 180
• 181
• 182
• 183
• 184
• Nästa >