1.1 This practice covers sampling of coarse and fine aggregates for the following purposes: 1.1.1 Preliminary investigation of the potential source of supply, 1.1.2 Control of the product at the so...
2009-06-01
1.1 This guide provides guidelines for several techniques of measuring the foam stability of light-duty hand dishwashing detergent products in the presence of artificially applied test-food soils. ...
2006-02-01
1.1 This test method covers the determination of fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value. The specimens ...
2011-09-16
1.1 This specification covers requirements for the fluorocarbon terpolymer elastomer used in the manufacture of expansion joints for use in coal-fired utilities and other high temperature industria...
2010-09-17
1.1 This specification covers mineral oils used in hydraulic systems, where the performance requirements demand fluids with one of the following characteristics: 1.1.1 A refined base oil (Class HH)...
1.1 This test method covers the determination of relative density and absorption of fine aggregates by Method A and coarse and blended aggregates by Method B. 1.2 The values are stated in SI units ...
1.1 This specification covers general requirements common to wrought precious metal electrical contact alloy products in the form of sheet, strip, wire, and rod. Unless otherwise specified in th...
2006-06-01
1.1 The purpose of this guide is to assist practitioners in the development, selection, design, and implementation of partial, short-term, or early action remedies undertaken at sites of waste cont...
2009-09-01
1.1 This specification covers the physical requirements for tools used to squeeze-off polyethylene (PE) pipe and tubing. It is limited to squeeze-off procedures set forth by the pipe manufacturer ...
2007-09-05
1.1 This specification covers refined gold in cast bar form (Note 1). This specification covers refined gold of Grades 99.5, 99.95, 99.99, and 99.995 in cast bar forms. Other forms of u...
2005-05-01
1.1 This practice covers the determination of the viscosity of glass above the softening point through the use of a platinum alloy spindle immersed in a crucible of molten glass. Spindle torque, de...
1.1 This practice covers procedures for the characterization of subsurface soil conditions at a site as part of the process for evaluating suitability for an on-site septic system. This practice pr...
1996-02-10
1.1 Ecological Risk Assessments (EcoRAs) typically focus on valued wildlife populations. Regulatory authority for conducting EcoRAs derives from various federal laws [for example, Comprehensive Env...
2011-11-18
1.1 This practice determines the compatibility of plasticizers in poly(vinyl chloride) plastics by rating the amount of plasticizer that spews due to compressional stress set up inside a 180&#x...
1.1 This test method, which is similar to thermal analysis techniques, establishes a procedure for determining flammability characteristics of combustible materials such as plastics. 1.2 The test i...
1.1 This test method covers the determination of the acid material, which disassociates in distilled water, that is present in sulfur. The acidity is determined by an electrometric or visual titrat...
2007-01-11
1.1 The following requirements apply for the manufacture of weight-shift-control aircraft. This specification includes Aircraft Operating Instructions (AOI) and Flight Training Supplement (FTS) req...
2008-03-12
1.1 This specification covers two types of 2¼ Cr-1 Mo and three types of Cr-Mo-V alloy steel plates for use in the quenched-and-tempered condition, intended for the fabrication of wel...
2009-10-01
1.1 This specification covers needle roller bearing assemblies. These assemblies have thick outer rings, cages, rollers, and inner rings. The assemblies consist of a MS51961 thick This s...
2004-10-01
1.1 This practice covers the determination of the existence of pinholes in one-time carbonizing tissues. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given i...
1.1 These test methods cover the determination of the mechanical properties of stress-graded lumber and other wood-base structural material. 1.2 These test methods appear in the following order:<...
2011-10-14
1.1 This specification covers bare round copper-clad steel wire for electronic application. 1.2 Four classes of copper-clad steel wire are covered as follows: 1.2.1 This specification covers bare r...
1.1 This test method covers the determination of the average molecular weight of a fatty quaternary ammonium chloride by converting to the acetate, titrating potentiometrically, and correcting for ...
1992-01-01
2007-03-20
1.1 This practice provides guidance for testing the physical properties, design considerations, construction practices, and leachate generation potential of processed or whole scrap tires in lieu o...
2008-09-01
1.1 This test method covers the determination of total sediment up to 0.40 % m/m for distillate fuel oils containing residual components and to 0.50 % m/m in residual fuel oils having a maximum v...
2009-04-15
1.1 Test Methods 1, 2, and 3—These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not
2005-06-01
1.1 This test method covers laboratory filter papers as passive sensors to evaluate the soil matric (matrix) and total potential (suction), a measure of the free energy of the pore-water or tension...
1.1 This test method covers the corrosiveness of hydraulic and lubricating fluids to a bimetallic galvanic couple. Note 1—This test method replicates Fed-Std No. 791, Meth
1.1 This test method covers a recommended procedure for examining odor and taste properties of polymeric film intended for use as flexible packaging materials. This test method can be used for sing...
1.1 This test method covers the determination of the colorfastness of colored leathers, with or without a surface coating. The leathers to be tested are of the type normally expected to withstand ...
2011-05-20