21317 träffar på

Standard · ASTM ASTM F2076 Standard Practice for Communicating an EMS Patient Report to Receiving Medical Facilities 1.1 This practice establishes the EMS standard for communications entailing a patient radio (phone) report to a receiving medical facility.1.1.1 This report is based on receiving facility needs and... Språk Publicerad 2006-03-01

PDF · 468 SEK

Standard · ASTM ASTM C1522 Standard Test Method for Extensibility After Heat Aging of Cold Liquid-Applied Elastomeric Waterproofing Membranes 1.1 This test method describes a laboratory procedure for determining extensibility for one- or two-component cold liquid-applied elastomeric waterproofing membranes.1.2 The values stated in SI uni... Språk Publicerad 2005-05-01

PDF · 468 SEK

Standard · ASTM ASTM D2751 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings 1.1 This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. Included a... Språk Publicerad 2005-05-01

PDF · 533 SEK

Standard · ASTM ASTM D3149 Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation DESIG: D3149 06 ^TITLE: Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation ^SCOPE:1. Scope 1.1 This specification covers flexible and semirigid cros... Språk Publicerad 2006-04-01

PDF · 468 SEK

Standard · ASTM ASTM E2353 Standard Test Methods for Performance of Glass in Permanent Glass Railing Systems, Guards, and Balustrades 1.1 These test methods cover procedures to be followed in testing the performance of glass in permanent railing systems, guards and balustrades installed in and for assembly, commercial, educationa... Språk Publicerad 2006-06-01

PDF · 533 SEK

Standard · ASTM ASTM B929 Standard Specification for Copper-Nickel-Tin Spinodal Alloy Rod and Bar 1.1 This specification establishes the requirements for copper-nickel-tin alloy rod and bar. The following alloy is included:Copper Alloy UNS No. Nominal Composition, Weight %Cop This specification... Språk Publicerad 2005-06-01

PDF · 468 SEK

Standard · ASTM ASTM F1050 Standard Test Method for Determining Winding Torque and Tension of Typewriter Ribbons 1.1 This test method covers the determination of film ribbon cartridge wind tension and torque. The instruments described in this procedure may be used for specification acceptance, manufacturing c... Språk Publicerad 2005-06-01

PDF · 468 SEK

Standard · ASTM ASTM F2565 Standard Guide for Extensively Irradiation-Crosslinked Ultra-High Molecular Weight Polyethylene Fabricated Forms for Surgical Implant Applications 1.1 This guide covers extensively crosslinked ultra-high molecular weight polyethylene (UHMWPE) materials (fabricated forms) that are produced starting with virgin resin powders and consolidated fo... Språk Publicerad 2006-07-01

PDF · 468 SEK

Standard · ASTM ASTM E354 Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys 1.1 These test methods cover the chemical analysis of high-temperature, electrical, magnetic, and other similar iron, nickel, and cobalt alloys having chemical compositions within the following lim... Språk Publicerad 2006-06-01

PDF · 767 SEK

Standard · ASTM ASTM B352/B352M Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application 1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate.1.2 One unalloyed and three alloys for use in nuclear applications are described.1.3 The pro... Språk Publicerad 2002-06-10

PDF · 533 SEK

Standard · ASTM ASTM F1193 Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices 1.1 This practice establishes the minimum requirements for a quality assurance program and the manufacturing of amusement rides and devices (including major modifications). 1.2 This standard does n... Språk Publicerad 2006-03-01

PDF · 611 SEK

Standard · ASTM ASTM D5161 Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) 1.1 This guide is intended to aid the coating specification writer in selecting and specifying the appropriate inspection requirements. It indicates the inspection requirements that may be employed... Språk Publicerad 2004-08-01

PDF · 468 SEK

Standard · ASTM ASTM C694 Standard Test Method for Weight Loss (Mass Loss) of Sheet Steel During Immersion in Sulfuric Acid Solution 1.1 This test method covers the evaluation of the weight-loss (mass loss) characteristics of sheet steel in sulfuric acid solution. 1.2 This test method provides means of rating the effectiveness o... Språk Publicerad 2006-04-01

PDF · 533 SEK

Standard · ASTM ASTM F1584 Standard Practice for Marking Buildings During Disaster Search Operations 1.1 This practice covers the methodology for marking buildings that have been searched during disaster responses.1.2 This standard does not purport to address all of the safety concerns, if any, as... Språk Publicerad 2003-04-10

PDF · 468 SEK

Standard · ASTM ASTM G44 Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5% Sodium Chloride Solution 1.1 This practice covers procedures for making alternate immersion stress corrosion tests in 3.5 % sodium chloride (NaCl) (). It is primarily for tests of aluminum alloys (Test Method G 47) and fer... Språk Publicerad 2005-05-01

PDF · 533 SEK

Standard · ASTM ASTM D6530 Standard Test Method for Total Active Biomass in Cooling Tower Waters (Kool Kount Assay; KKA) 1.1 This test method covers the determination of viable active biomass in cooling tower water in the range from 102 to 108 cfu/mL (1). It is a semiquantitative test method.1.2 This test method was ... Språk Publicerad 2006-07-01

PDF · 468 SEK

Standard · ASTM ASTM D7227 Standard Practice for Rapid Drying of Compacted Asphalt Specimens Using Vacuum Drying Apparatus 1.1 This practice covers the process of drying compacted asphalt specimens using vacuum drying apparatus.1.2 The specimens dried by this practice remain at room temperature, which helps in maintain... Språk Publicerad 2006-02-15

PDF · 468 SEK

Standard · ASTM ASTM C448 Standard Test Methods for Abrasion Resistance of Porcelain Enamels 1.1 These test methods cover determination of the resistance of porcelain enamels to surface abrasion and subsurface abrasion.This standard does not purport to address all of the safety concerns, i... Språk Publicerad 2006-04-01

PDF · 533 SEK

Standard · ASTM ASTM B701/B701M Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD) 1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, steel-reinforced (ACSR/SD), and its component wires for use as overhead electrical conductors (Explanatory Not... Språk Publicerad 2006-03-01

PDF · 533 SEK

Standard · ASTM ASTM D4329 Standard Practice for Fluorescent UV Exposure of Plastics 1.1 This practice covers specific procedures and test conditions that are applicable for fluorescent UV exposure of plastics conducted in accordance with Practices G 151 and G 154. This practice al... Språk Publicerad 2005-07-15

PDF · 533 SEK

Standard · ASTM ASTM F1999 Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Fence Systems 1.1 This practice covers the minimum requirement for and methods of installation for rigid poly(vinyl chloride) (PVC) fencing systems and fence accessories in areas where the maximum frost penetrat... Språk Publicerad 2006-06-01

PDF · 468 SEK

Standard · ASTM ASTM D6995 Standard Test Method for Determining Field VMA based on the Maximum Specific Gravity of the Mix (Gmm) 1.1 This test method is intended to be used for a rapid field determination of voids in mineral aggregate (VMA) of hot mix asphalt (HMA). It provides equations for calculating the VMA based on the... Språk Publicerad 2005-09-15

PDF · 468 SEK

Standard · ASTM ASTM D3991 Standard Specifications for Fineness of Wool or Mohair and Assignment of Grade 1.1 These specifications cover the classification, by fineness grade, of wool or mohair that is in the grease, pulled, washed, or scoured state, or in the form of card sliver.1.2 These specificatio... Språk Publicerad 2007-02-07

PDF · 468 SEK

Standard · ASTM ASTM E659 Standard Test Method for Autoignition Temperature of Liquid Chemicals 1.1 This test method covers the determination of hot- and cool-flame autoignition temperatures of a liquid chemical in air at atmospheric pressure in a uniformly heated vessel. Note 1—Wit... Språk Publicerad 2005-09-15

PDF · 533 SEK

Standard · ASTM ASTM E633 Standard Guide for Use of Thermocouples in Creep and Stress-Rupture Testing to 1800°F (1000°C) in Air 1.1 This guide covers the use of ANSI thermocouple Types K, N, R, and S for creep and stress-rupture testing at temperatures up to 1800°F (1000°C) in air at one atmosphere of pres... Språk Publicerad 2005-05-01

PDF · 533 SEK

Standard · ASTM ASTM F2528 Standard Test Methods for Enteral Feeding Devices with a Retention Balloon 1.1 These test methods cover the establishment of performance requirements for the utilization of a single-use, enteral feeding device with a retention balloon, used by medical professionals for pr... Språk Publicerad 2006-06-01

PDF · 533 SEK

Standard · ASTM ASTM F771 Standard Specification for Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems 1.1 This specification covers polyethylene (PE) thermoplastic pipelines used to convey, at rated pressures of 80 to 200 psi, water that is to be used for irrigation purposes. This specification inc... Språk Publicerad 2005-08-01

PDF · 533 SEK

Standard · ASTM ASTM D1742 Standard Test Method for Oil Separation from Lubricating Grease During Storage 1.1 This test method covers the determination of the tendency of a lubricating grease to separate oil during storage in both normally filled and partially filled containers.1.2 This test method is ... Språk Publicerad 2006-05-01

PDF · 533 SEK

Standard · ASTM ASTM F1022 Standard Specification for Chemical Sanitizing Commercial Dishwashing Machines, Recirculated Wash, Fresh Water Rinse Type 1.1 This specification covers manually fed, spray-type, stationary rack, automatically controlled chemical sanitizing commercial dishwashing machines. Note 1—Several standards that apply ... Språk Publicerad 2006-04-01

PDF · 533 SEK

Standard · ASTM ASTM B947 Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate 1.1 This practice establishes the controls required for hot rolling mill solution heat treatment of the 6xxx series aluminum alloy plate in when ASTM material specifications allow use of this proc... Språk Publicerad 2006-07-01

PDF · 468 SEK

• < Föregående
• 198
• 199
• 200
• 201
• 202
• 203
• 204
• 205
• 206
• 207
• Nästa >